diff mbox series

[v3,2/2] iio: adc: ad7173: add AD7173 driver

Message ID 20231005105921.460657-2-mitrutzceclan@gmail.com
State New
Headers show
Series [v3,1/2] dt-bindings: adc: add AD7173 | expand

Commit Message

Dumitru Ceclan Oct. 5, 2023, 10:59 a.m. UTC
The AD7173 family offer a complete integrated Sigma-Delta ADC solution
which can be used in high precision, low noise single channel
applications or higher speed multiplexed applications. The Sigma-Delta
ADC is intended primarily for measurement of signals close to DC but also
delivers outstanding performance with input bandwidths out to ~10kHz.

Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>
---
V2 -> V3

 - change Kconfig GPIO_REGMAP and REGMAP_SPI to be conditioned by GPIOLIB
 - cast chip info to (kernel_ulong_t) to suppress warnings
 - adjust copyright year to reflect the out-of-tree history
 - remove unused sysfs and trigger header files
 - clean up defined macros by using FIELD_PREP( ) inline
 - use DECLARE_BITMAP( ) for defiining cfg_slots_status
 - use clear/set _bit instead of assign_bit
 - rename state field regmap to reg_gpiocon_regmap to better represent usage
 - replace container_of( ) usages to ad_sigma_delta_to_ad7173( )
 - improve readability of sampling frequency conversion in write_raw( )
				specifying conversion from Micro to Milli
 - use iio_device_claim_direct_mode( ) correctly in write_raw( )
 - flip logic in write_raw( ) to reduce line length
 - pass only state struct to gpio_init function
 - remove else branch at end of probe
 - remove comma after list terminator for of_match and id_table arrays
 - clarify write_raw( ) realbits 32 bit size check in a comment
 - change parsed fw property 'adi,bipolar' to 'bipolar' to matched referenced adc.yaml 
 - use reg_set_base for gpio regmap xlate 

 drivers/iio/adc/Kconfig  |  13 +
 drivers/iio/adc/Makefile |   1 +
 drivers/iio/adc/ad7173.c | 843 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 857 insertions(+)
 create mode 100644 drivers/iio/adc/ad7173.c

Comments

Dumitru Ceclan Oct. 6, 2023, 2:18 p.m. UTC | #1
On 10/5/23 20:01, Jonathan Cameron wrote:
> On Thu,  5 Oct 2023 13:59:22 +0300
> Dumitru Ceclan <mitrutzceclan@gmail.com> wrote:
> 
>> The AD7173 family offer a complete integrated Sigma-Delta ADC solution
>> which can be used in high precision, low noise single channel
>> applications or higher speed multiplexed applications. The Sigma-Delta
>> ADC is intended primarily for measurement of signals close to DC but also
>> delivers outstanding performance with input bandwidths out to ~10kHz.
>>

...

>> +	case IIO_CHAN_INFO_RAW:
>> +		ret = ad_sigma_delta_single_conversion(indio_dev, chan, val);
> 
> It's fairly usual for it to be safe to grab a single conversion when the
> buffered mode might be enabled.  Do you need an iio_device_claim_direct_mode()
> here?
> 
ad_sigma_delta_single_conversion() calls iio_device_claim_direct_mode()


>> +static int ad7173_update_scan_mode(struct iio_dev *indio_dev,
>> +				   const unsigned long *scan_mask)
>> +{
>> +	struct ad7173_state *st = iio_priv(indio_dev);
>> +	int i, ret = 0;
>> +
>> +	iio_device_claim_direct_mode(indio_dev);
> 
> This looks wrong.
> Firstly iio_device_claim_direct_mode() can fail so you always have
> to check the return value. If it does fail and you then call
> iio_release_direct_mode() it is unbalanced release of a mutex.
> 
> Secondly update_scan_mode is only called as part of buffer setup
> and there should be no races around that (and the mutex this
> tries to grab is already held.
> https://elixir.bootlin.com/linux/latest/source/drivers/iio/industrialio-buffer.c#L1265
> )
> 
> If you are protecting something device specific (rather than
> the mode) then a device specific lock should be taken.
> 

The use of a lock was inspired from ad7124, but from looking at it the only use it has
was to protect concurrent access of the device setup from write_raw (that now uses ...direct_mode())

I think it's best to drop this lock. 


>> +		chan[chan_index].differential = fwnode_property_read_bool(child, "bipolar");
> 
> bipolar doesn't normally == differential. 
> You can have unipolar differential (just that you can't get a negative answer)
> Perhaps just a terminology thing?
>

This device supports only differential channels. Here, the differential flag is used to show
if bipolar coding should be used.


>> +	st->info = device_get_match_data(dev);
>> +	if (!st->info)
>> +		return -ENODEV;
> This works for the cases of DT and ACPI but not for anyone just
> using the spi_device_id table. 
> There is spi_device_get_match_data() to cover all options.
> 
I could not find the spi_device_get_match_data() function in the repo.
It appears however as a suggestion from Andy Shevchenko in a thread:
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg2382960.html
 Is this it?
Michael Walle Oct. 9, 2023, 7:42 a.m. UTC | #2
> The AD7173 family offer a complete integrated Sigma-Delta ADC solution
> which can be used in high precision, low noise single channel
> applications or higher speed multiplexed applications. The Sigma-Delta
> ADC is intended primarily for measurement of signals close to DC but 
> also
> delivers outstanding performance with input bandwidths out to ~10kHz.
> 
> Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>

Reviewed-by: Michael Walle <michael@walle.cc> # for gpio-regmap

-michael
diff mbox series

Patch

diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 517b3db114b8..7da383301001 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -54,6 +54,19 @@  config AD7124
 	  To compile this driver as a module, choose M here: the module will be
 	  called ad7124.
 
+config AD7173
+	tristate "Analog Devices AD7173 driver"
+	depends on SPI_MASTER
+	select AD_SIGMA_DELTA
+	select GPIO_REGMAP if GPIOLIB
+	select REGMAP_SPI if GPIOLIB
+	help
+	  Say yes here to build support for Analog Devices AD7173 and similar ADC
+	  (currently supported: AD7172-2, AD7173-8, AD7175-2, AD7176-2).
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called ad7173.
+
 config AD7192
 	tristate "Analog Devices AD7190 AD7192 AD7193 AD7195 ADC driver"
 	depends on SPI
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 2facf979327d..8c70333ae967 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -9,6 +9,7 @@  obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o
 obj-$(CONFIG_AD4130) += ad4130.o
 obj-$(CONFIG_AD7091R5) += ad7091r5.o ad7091r-base.o
 obj-$(CONFIG_AD7124) += ad7124.o
+obj-$(CONFIG_AD7173) += ad7173.o
 obj-$(CONFIG_AD7192) += ad7192.o
 obj-$(CONFIG_AD7266) += ad7266.o
 obj-$(CONFIG_AD7280) += ad7280a.o
diff --git a/drivers/iio/adc/ad7173.c b/drivers/iio/adc/ad7173.c
new file mode 100644
index 000000000000..5f9ab6023b09
--- /dev/null
+++ b/drivers/iio/adc/ad7173.c
@@ -0,0 +1,843 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * AD7172-2/AD7173-8/AD7175-2/AD7176-2 SPI ADC driver
+ * Copyright (C) 2015-2023 Analog Devices, Inc.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitmap.h>
+#include <linux/bits.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/gpio/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/units.h>
+
+#include <linux/iio/buffer.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+
+#include <linux/iio/adc/ad_sigma_delta.h>
+
+#define AD7173_REG_COMMS		0x00
+#define AD7173_REG_ADC_MODE		0x01
+#define AD7173_REG_INTERFACE_MODE	0x02
+#define AD7173_REG_CRC			0x03
+#define AD7173_REG_DATA			0x04
+#define AD7173_REG_GPIO			0x06
+#define AD7173_REG_ID			0x07
+#define AD7173_REG_CH(x)		(0x10 + (x))
+#define AD7173_REG_SETUP(x)		(0x20 + (x))
+#define AD7173_REG_FILTER(x)		(0x28 + (x))
+#define AD7173_REG_OFFSET(x)		(0x30 + (x))
+#define AD7173_REG_GAIN(x)		(0x38 + (x))
+
+#define AD7173_RESET_LENGTH		BITS_TO_BYTES(64)
+
+#define AD7173_CH_ENABLE		BIT(15)
+#define AD7173_CH_SETUP_SEL_MASK	GENMASK(14, 12)
+#define AD7173_CH_SETUP_AINPOS_MASK	GENMASK(9, 5)
+
+#define AD7173_CH_ADDRESS(pos, neg) \
+	(FIELD_PREP(AD7173_CH_SETUP_AINPOS_MASK, pos) |\
+	 FIELD_PREP(AD7173_CH_SETUP_AINPOS_MASK, neg))
+#define AD7173_AIN_TEMP_POS	17
+#define AD7173_AIN_TEMP_NEG	18
+
+#define AD7172_ID			0x00d0
+#define AD7173_ID			0x30d0
+#define AD7175_ID			0x0cd0
+#define AD7176_ID			0x0c90
+#define AD7173_ID_MASK			GENMASK(15, 4)
+
+#define AD7173_ADC_MODE_REF_EN		BIT(15)
+#define AD7173_ADC_MODE_SING_CYC	BIT(13)
+#define AD7173_ADC_MODE_MODE_MASK	GENMASK(6, 4)
+#define AD7173_ADC_MODE_CLOCKSEL_MASK	GENMASK(3, 2)
+
+#define AD7173_GPIO_PDSW	BIT(14)
+#define AD7173_GPIO_OP_EN2_3	BIT(13)
+#define AD7173_GPIO_MUX_IO	BIT(12)
+#define AD7173_GPIO_SYNC_EN	BIT(11)
+#define AD7173_GPIO_ERR_EN	BIT(10)
+#define AD7173_GPIO_ERR_DAT	BIT(9)
+#define AD7173_GPIO_GP_DATA3	BIT(7)
+#define AD7173_GPIO_GP_DATA2	BIT(6)
+#define AD7173_GPIO_IP_EN1	BIT(5)
+#define AD7173_GPIO_IP_EN0	BIT(4)
+#define AD7173_GPIO_OP_EN1	BIT(3)
+#define AD7173_GPIO_OP_EN0	BIT(2)
+#define AD7173_GPIO_GP_DATA1	BIT(1)
+#define AD7173_GPIO_GP_DATA0	BIT(0)
+
+#define AD7173_GPO12_DATA(x)	BIT(x)
+#define AD7173_GPO23_DATA(x)	BIT(x + 4)
+#define AD7173_GPO_DATA(x)	(x < 2 ? AD7173_GPO12_DATA(x) : AD7173_GPO23_DATA(x))
+
+#define AD7173_INTERFACE_DATA_STAT	BIT(6)
+#define AD7173_INTERFACE_DATA_STAT_EN(x)\
+	FIELD_PREP(AD7173_INTERFACE_DATA_STAT, x)
+
+#define AD7173_SETUP_BIPOLAR		BIT(12)
+#define AD7173_SETUP_AREF_BUF_MASK	GENMASK(11, 10)
+#define AD7173_SETUP_AIN_BUF_MASK	GENMASK(9, 8)
+
+#define AD7173_SETUP_REF_SEL_MASK	GENMASK(5, 4)
+#define AD7173_SETUP_REF_SEL_AVDD1_AVSS	0x3
+#define AD7173_SETUP_REF_SEL_INT_REF	0x2
+#define AD7173_SETUP_REF_SEL_EXT_REF2	0x1
+#define AD7173_SETUP_REF_SEL_EXT_REF	0x0
+
+#define AD7173_FILTER_ODR0_MASK		GENMASK(5, 0)
+#define AD7173_MAX_CONFIGS		8
+
+enum ad7173_ids {
+	ID_AD7172_2,
+	ID_AD7173_8,
+	ID_AD7175_2,
+	ID_AD7176_2,
+};
+
+struct ad7173_device_info {
+	unsigned int id;
+	unsigned int num_inputs;
+	unsigned int num_configs;
+	unsigned int num_channels;
+	unsigned char num_gpios;
+	bool has_temp;
+	unsigned int clock;
+
+	const unsigned int *sinc5_data_rates;
+	unsigned int num_sinc5_data_rates;
+};
+
+struct ad7173_channel_config {
+	bool live;
+	unsigned char cfg_slot;
+	/* Following fields are used to compare equality. Bipolar must be first */
+	bool bipolar;
+	bool input_buf;
+	unsigned char odr;
+};
+
+struct ad7173_channel {
+	unsigned int chan_reg;
+	struct ad7173_channel_config cfg;
+	unsigned int ain;
+};
+
+struct ad7173_state {
+	const struct ad7173_device_info *info;
+	struct ad_sigma_delta sd;
+	struct ad7173_channel *channels;
+	struct regulator *reg;
+	unsigned int adc_mode;
+	unsigned int interface_mode;
+	unsigned int num_channels;
+	DECLARE_BITMAP(cfg_slots_status, AD7173_MAX_CONFIGS); /* slots usage status */
+	unsigned long long config_usage_counter;
+	unsigned long long *config_cnts;
+#if IS_ENABLED(CONFIG_GPIOLIB)
+	struct regmap *reg_gpiocon_regmap;
+	struct gpio_regmap *gpio_regmap;
+#endif
+};
+
+static const unsigned int ad7173_sinc5_data_rates[] = {
+	6211000, 6211000, 6211000, 6211000, 6211000, 6211000, 5181000, 4444000,
+	3115000, 2597000, 1007000, 503800,  381000,  200300,  100500,  59520,
+	49680,	 20010,	  16333,   10000,   5000,    2500,    1250,
+};
+
+static const unsigned int ad7175_sinc5_data_rates[] = {
+	50000000, 41667000, 31250000, 27778000, 20833000, 17857000, 12500000,
+	10000000, 5000000,  2500000,  1000000,	500000,	  397500,   200000,
+	100000,	  59920,    49960,    20000,	16666,	  10000,    5000,
+};
+
+static const struct ad7173_device_info ad7173_device_info[] = {
+	[ID_AD7172_2] = {
+		.id = AD7172_ID,
+		.num_inputs = 5,
+		.num_channels = 4,
+		.num_configs = 4,
+		.num_gpios = 2,
+		.has_temp = true,
+		.clock = 2 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7173_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+	},
+	[ID_AD7173_8] = {
+		.id = AD7173_ID,
+		.num_inputs = 17,
+		.num_channels = 16,
+		.num_configs = 8,
+		.num_gpios = 4,
+		.has_temp = true,
+		.clock = 2 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7173_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7173_sinc5_data_rates),
+	},
+	[ID_AD7175_2] = {
+		.id = AD7175_ID,
+		.num_inputs = 5,
+		.num_channels = 4,
+		.num_configs = 4,
+		.num_gpios = 2,
+		.has_temp = true,
+		.clock = 16 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7175_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7175_sinc5_data_rates),
+	},
+	[ID_AD7176_2] = {
+		.id = AD7176_ID,
+		.num_inputs = 5,
+		.num_channels = 4,
+		.num_configs = 4,
+		.num_gpios = 2,
+		.has_temp = false,
+		.clock = 16 * HZ_PER_MHZ,
+		.sinc5_data_rates = ad7175_sinc5_data_rates,
+		.num_sinc5_data_rates = ARRAY_SIZE(ad7175_sinc5_data_rates),
+	},
+};
+
+#if IS_ENABLED(CONFIG_GPIOLIB)
+
+static const struct regmap_range ad7173_range_gpio[] = {
+	regmap_reg_range(AD7173_REG_GPIO, AD7173_REG_GPIO),
+};
+
+static const struct regmap_access_table ad7173_access_table = {
+	.yes_ranges = ad7173_range_gpio,
+	.n_yes_ranges = ARRAY_SIZE(ad7173_range_gpio),
+};
+
+static const struct regmap_config ad7173_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 16,
+	.rd_table = &ad7173_access_table,
+	.wr_table = &ad7173_access_table,
+	.read_flag_mask = BIT(6),
+};
+
+static int ad7173_mask_xlate(struct gpio_regmap *gpio, unsigned int base,
+			     unsigned int offset, unsigned int *reg,
+			     unsigned int *mask)
+{
+	*mask = AD7173_GPO_DATA(offset);
+	*reg = base;
+	return 0;
+}
+
+static int ad7173_gpio_init(struct ad7173_state *st)
+{
+	struct gpio_regmap_config gpio_regmap = {};
+	struct device *dev = &st->sd.spi->dev;
+	unsigned int mask;
+
+	st->reg_gpiocon_regmap = devm_regmap_init_spi(st->sd.spi, &ad7173_regmap_config);
+	if (IS_ERR(st->reg_gpiocon_regmap)) {
+		return dev_err_probe(dev, PTR_ERR(st->reg_gpiocon_regmap),
+				     "Unable to init regmap\n");
+	}
+
+	mask = AD7173_GPIO_OP_EN0 | AD7173_GPIO_OP_EN1 | AD7173_GPIO_OP_EN2_3;
+	regmap_update_bits(st->reg_gpiocon_regmap, AD7173_REG_GPIO, mask, mask);
+
+	gpio_regmap.parent = dev;
+	gpio_regmap.regmap = st->reg_gpiocon_regmap;
+	gpio_regmap.ngpio = st->info->num_gpios;
+	gpio_regmap.reg_set_base = AD7173_REG_GPIO;
+	gpio_regmap.reg_mask_xlate = ad7173_mask_xlate;
+
+	st->gpio_regmap = devm_gpio_regmap_register(dev, &gpio_regmap);
+	if (IS_ERR(st->gpio_regmap)) {
+		return dev_err_probe(dev, PTR_ERR(st->gpio_regmap),
+				     "Unable to init gpio-regmap\n");
+	}
+
+	return 0;
+}
+
+#endif /* CONFIG_GPIOLIB */
+
+static struct ad7173_state *ad_sigma_delta_to_ad7173(struct ad_sigma_delta *sd)
+{
+	return container_of(sd, struct ad7173_state, sd);
+}
+
+static void ad7173_reset_usage_cnts(struct ad7173_state *st)
+{
+	memset64(st->config_cnts, 0, st->info->num_configs);
+	st->config_usage_counter = 0;
+}
+
+static struct ad7173_channel_config *ad7173_find_live_config
+	(struct ad7173_state *st, struct ad7173_channel_config *cfg)
+{
+	struct ad7173_channel_config *cfg_aux;
+	ptrdiff_t cmp_size, offset;
+	int i;
+
+	offset = offsetof(struct ad7173_channel_config, cfg_slot) +
+		 sizeof(cfg->cfg_slot);
+	cmp_size = sizeof(*cfg) - offset;
+
+	for (i = 0; i < st->num_channels; i++) {
+		cfg_aux = &st->channels[i].cfg;
+
+		if (cfg_aux->live && !memcmp(&cfg->bipolar, &cfg_aux->bipolar,
+					     cmp_size))
+			return cfg_aux;
+	}
+	return NULL;
+}
+
+static int ad7173_free_config_slot_lru(struct ad7173_state *st)
+{
+	int i, lru_position = 0;
+
+	for (i = 1; i < st->info->num_configs; i++)
+		if (st->config_cnts[i] < st->config_cnts[lru_position])
+			lru_position = i;
+
+	for (i = 0; i < st->num_channels; i++)
+		if (st->channels[i].cfg.cfg_slot == lru_position)
+			st->channels[i].cfg.live = false;
+
+	clear_bit(lru_position, st->cfg_slots_status);
+	return lru_position;
+}
+
+static int ad7173_load_config(struct ad7173_state *st,
+			      struct ad7173_channel_config *cfg)
+{
+	unsigned int config;
+	int free_cfg_slot, ret;
+
+	free_cfg_slot = find_first_zero_bit(st->cfg_slots_status,
+					    st->info->num_configs);
+	if (free_cfg_slot == st->info->num_configs)
+		free_cfg_slot = ad7173_free_config_slot_lru(st);
+
+	set_bit(free_cfg_slot, st->cfg_slots_status);
+	cfg->cfg_slot = free_cfg_slot;
+
+	config = FIELD_PREP(AD7173_SETUP_REF_SEL_MASK, AD7173_SETUP_REF_SEL_INT_REF);
+
+	if (cfg->bipolar)
+		config |= AD7173_SETUP_BIPOLAR;
+
+	if (cfg->input_buf)
+		config |= AD7173_SETUP_AIN_BUF_MASK;
+
+	ret = ad_sd_write_reg(&st->sd, AD7173_REG_SETUP(free_cfg_slot), 2, config);
+	if (ret)
+		return ret;
+
+	return ad_sd_write_reg(&st->sd, AD7173_REG_FILTER(free_cfg_slot), 2,
+			       AD7173_FILTER_ODR0_MASK & cfg->odr);
+}
+
+static int ad7173_config_channel(struct ad7173_state *st, int addr)
+{
+	struct ad7173_channel_config *cfg = &st->channels[addr].cfg;
+	struct ad7173_channel_config *live_cfg;
+	int ret;
+
+	if (!cfg->live) {
+		live_cfg = ad7173_find_live_config(st, cfg);
+		if (live_cfg) {
+			cfg->cfg_slot = live_cfg->cfg_slot;
+		} else {
+			ret = ad7173_load_config(st, cfg);
+			if (ret)
+				return ret;
+			cfg->live = true;
+		}
+	}
+
+	if (st->config_usage_counter == U64_MAX)
+		ad7173_reset_usage_cnts(st);
+
+	st->config_usage_counter++;
+	st->config_cnts[cfg->cfg_slot] = st->config_usage_counter;
+
+	return 0;
+}
+
+static int ad7173_set_channel(struct ad_sigma_delta *sd, unsigned int channel)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+	unsigned int val;
+	int ret;
+
+	ret = ad7173_config_channel(st, channel);
+	if (ret)
+		return ret;
+
+	val = AD7173_CH_ENABLE |
+	      FIELD_PREP(AD7173_CH_SETUP_SEL_MASK, st->channels[channel].cfg.cfg_slot) |
+	      st->channels[channel].ain;
+
+	return ad_sd_write_reg(&st->sd, AD7173_REG_CH(channel), 2, val);
+}
+
+static int ad7173_set_mode(struct ad_sigma_delta *sd,
+			   enum ad_sigma_delta_mode mode)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+
+	st->adc_mode &= ~AD7173_ADC_MODE_MODE_MASK;
+	st->adc_mode |= FIELD_PREP(AD7173_ADC_MODE_MODE_MASK, mode);
+
+	return ad_sd_write_reg(&st->sd, AD7173_REG_ADC_MODE, 2, st->adc_mode);
+}
+
+static int ad7173_append_status(struct ad_sigma_delta *sd, bool append)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+	unsigned int interface_mode = st->interface_mode;
+	int ret;
+
+	interface_mode |= AD7173_INTERFACE_DATA_STAT_EN(append);
+	ret = ad_sd_write_reg(&st->sd, AD7173_REG_INTERFACE_MODE, 2, interface_mode);
+	if (ret)
+		return ret;
+
+	st->interface_mode = interface_mode;
+
+	return 0;
+}
+
+static int ad7173_disable_all(struct ad_sigma_delta *sd)
+{
+	struct ad7173_state *st = ad_sigma_delta_to_ad7173(sd);
+	int ret;
+	int i;
+
+	for (i = 0; i < st->num_channels; i++) {
+		ret = ad_sd_write_reg(sd, AD7173_REG_CH(i), 2, 0);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static struct ad_sigma_delta_info ad7173_sigma_delta_info = {
+	.set_channel = ad7173_set_channel,
+	.append_status = ad7173_append_status,
+	.disable_all = ad7173_disable_all,
+	.set_mode = ad7173_set_mode,
+	.has_registers = true,
+	.addr_shift = 0,
+	.read_mask = BIT(6),
+	.status_ch_mask = GENMASK(3, 0),
+	.data_reg = AD7173_REG_DATA,
+	.irq_flags = IRQF_TRIGGER_FALLING,
+};
+
+static int ad7173_setup(struct iio_dev *indio_dev)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	unsigned int id;
+	u8 buf[AD7173_RESET_LENGTH];
+	int ret;
+
+	/* reset the serial interface */
+	memset(buf, 0xff, AD7173_RESET_LENGTH);
+	ret = spi_write_then_read(st->sd.spi, buf, sizeof(buf), NULL, 0);
+	if (ret < 0)
+		return ret;
+
+	/* datasheet recommends a delay of at least 500us after reset */
+	fsleep(500);
+
+	ret = ad_sd_read_reg(&st->sd, AD7173_REG_ID, 2, &id);
+	if (ret)
+		return ret;
+
+	id &= AD7173_ID_MASK;
+	if (id != st->info->id)
+		dev_warn(&st->sd.spi->dev,
+			 "Unexpected device id: %x, expected: %x\n",
+			 id, st->info->id);
+
+	st->adc_mode |= AD7173_ADC_MODE_REF_EN | AD7173_ADC_MODE_SING_CYC;
+	st->interface_mode = 0x0;
+
+	st->config_usage_counter = 0;
+	st->config_cnts = devm_kcalloc(indio_dev->dev.parent,
+				       st->info->num_configs, sizeof(u64),
+				       GFP_KERNEL);
+	if (!st->config_cnts)
+		return -ENOMEM;
+
+	/* All channels are enabled by default after a reset */
+	return ad7173_disable_all(&st->sd);
+}
+
+static int ad7173_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long info)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	unsigned int reg;
+	int ret;
+
+	switch (info) {
+	case IIO_CHAN_INFO_RAW:
+		ret = ad_sigma_delta_single_conversion(indio_dev, chan, val);
+		if (ret < 0)
+			return ret;
+
+		/* disable channel after single conversion */
+		ret = ad_sd_write_reg(&st->sd, AD7173_REG_CH(chan->address), 2, 0);
+		if (ret < 0)
+			return ret;
+
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		if (chan->type == IIO_TEMP) {
+			*val = 250000000;
+			*val2 = 800273203; /* (2^24 * 477) / 10 */
+			return IIO_VAL_FRACTIONAL;
+		} else {
+			*val = 2500;
+			if (chan->differential)
+				*val2 = 23;
+			else
+				*val2 = 24;
+			return IIO_VAL_FRACTIONAL_LOG2;
+		}
+	case IIO_CHAN_INFO_OFFSET:
+		if (chan->type == IIO_TEMP) {
+			*val = -874379;
+		} else {
+			if (chan->differential)
+				/* (1<<31) is UB for a 32bit channel*/
+				*val = (chan->scan_type.realbits == 32) ?
+					-(1 << (chan->scan_type.realbits - 1)) :
+					INT_MIN;
+			else
+				*val = 0;
+		}
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		reg = st->channels[chan->address].cfg.odr;
+
+		*val = st->info->sinc5_data_rates[reg] / (MICRO/MILLI);
+		*val2 = (st->info->sinc5_data_rates[reg] % MILLI) * (MICRO/MILLI);
+
+		return IIO_VAL_INT_PLUS_MICRO;
+	}
+	return -EINVAL;
+}
+
+static int ad7173_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long info)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	struct ad7173_channel_config *cfg;
+	unsigned int freq, i, reg;
+	int ret;
+
+	ret = iio_device_claim_direct_mode(indio_dev);
+	if (ret)
+		return ret;
+
+	switch (info) {
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		freq = val * MILLI + val2 / MILLI;
+
+		for (i = 0; i < st->info->num_sinc5_data_rates - 1; i++) {
+			if (freq >= st->info->sinc5_data_rates[i])
+				break;
+		}
+
+		cfg = &st->channels[chan->address].cfg;
+		cfg->odr = i;
+
+		if (!cfg->live)
+			break;
+
+		ret = ad_sd_read_reg(&st->sd, AD7173_REG_FILTER(cfg->cfg_slot), 2, &reg);
+		if (ret)
+			break;
+		reg &= ~AD7173_FILTER_ODR0_MASK;
+		reg |= FIELD_PREP(AD7173_FILTER_ODR0_MASK, i);
+		ret = ad_sd_write_reg(&st->sd, AD7173_REG_FILTER(cfg->cfg_slot), 2, reg);
+		break;
+
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	iio_device_release_direct_mode(indio_dev);
+	return ret;
+}
+
+static int ad7173_update_scan_mode(struct iio_dev *indio_dev,
+				   const unsigned long *scan_mask)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	int i, ret = 0;
+
+	iio_device_claim_direct_mode(indio_dev);
+	for (i = 0; i < indio_dev->num_channels; i++) {
+		if (test_bit(i, scan_mask))
+			ret = ad7173_set_channel(&st->sd, i);
+		else
+			ret = ad_sd_write_reg(&st->sd, AD7173_REG_CH(i), 2, 0);
+
+		if (ret < 0)
+			goto out;
+	}
+
+out:
+	iio_device_release_direct_mode(indio_dev);
+	return ret;
+}
+
+static int ad7173_debug(struct iio_dev *indio_dev, unsigned int reg,
+			unsigned int writeval, unsigned int *readval)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	u8 reg_size;
+
+	if (reg == 0)
+		reg_size = 1;
+	else if (reg == AD7173_REG_CRC || reg == AD7173_REG_DATA ||
+		 reg >= AD7173_REG_OFFSET(0))
+		reg_size = 3;
+	else
+		reg_size = 2;
+
+	if (readval)
+		return ad_sd_read_reg(&st->sd, reg, reg_size, readval);
+
+	return ad_sd_write_reg(&st->sd, reg, reg_size, writeval);
+}
+
+static const struct iio_info ad7173_info = {
+	.read_raw = &ad7173_read_raw,
+	.write_raw = &ad7173_write_raw,
+	.debugfs_reg_access = &ad7173_debug,
+	.validate_trigger = ad_sd_validate_trigger,
+	.update_scan_mode = ad7173_update_scan_mode,
+};
+
+static const struct iio_chan_spec ad7173_channel_template = {
+	.type = IIO_VOLTAGE,
+	.indexed = 1,
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+		BIT(IIO_CHAN_INFO_SCALE),
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	.scan_type = {
+		.sign = 'u',
+		.realbits = 24,
+		.storagebits = 32,
+		.endianness = IIO_BE,
+	},
+};
+
+static const struct iio_chan_spec ad7173_temp_iio_channel_template = {
+	.type = IIO_TEMP,
+	.indexed = 1,
+	.channel = AD7173_AIN_TEMP_POS,
+	.channel2 = AD7173_AIN_TEMP_NEG,
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_OFFSET),
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+	.scan_type = {
+		.sign = 'u',
+		.realbits = 24,
+		.storagebits = 32,
+		.endianness = IIO_BE,
+	},
+};
+
+static int ad7173_fw_parse_channel_config(struct iio_dev *indio_dev)
+{
+	struct ad7173_state *st = iio_priv(indio_dev);
+	struct ad7173_channel *channels_st_priv;
+	struct fwnode_handle *child;
+	struct device *dev = indio_dev->dev.parent;
+	struct iio_chan_spec *chan;
+	unsigned int num_channels;
+	unsigned int ain[2], chan_index = 0;
+	int ret;
+
+	num_channels = device_get_child_node_count(dev);
+
+	if (st->info->has_temp)
+		num_channels++;
+
+	if (num_channels == 0)
+		return 0;
+	st->num_channels = num_channels;
+
+	chan = devm_kcalloc(dev, sizeof(*chan), num_channels,
+			    GFP_KERNEL);
+	if (!chan)
+		return -ENOMEM;
+
+	channels_st_priv = devm_kcalloc(dev, num_channels,
+					sizeof(*channels_st_priv), GFP_KERNEL);
+	if (!channels_st_priv)
+		return -ENOMEM;
+
+	indio_dev->channels = chan;
+	indio_dev->num_channels = num_channels;
+	st->channels = channels_st_priv;
+
+	if (st->info->has_temp) {
+		chan[chan_index] = ad7173_temp_iio_channel_template;
+		channels_st_priv[chan_index].ain =
+			AD7173_CH_ADDRESS(chan[chan_index].channel, chan[chan_index].channel2);
+		channels_st_priv[chan_index].cfg.bipolar = false;
+		channels_st_priv[chan_index].cfg.input_buf = true;
+		chan_index++;
+	}
+
+	device_for_each_child_node(dev, child) {
+		ret = fwnode_property_read_u32_array(child, "diff-channels",
+						     ain, ARRAY_SIZE(ain));
+		if (ret) {
+			fwnode_handle_put(child);
+			return ret;
+		}
+
+		if (ain[0] >= st->info->num_inputs ||
+		    ain[1] >= st->info->num_inputs) {
+			fwnode_handle_put(child);
+			return dev_err_probe(dev, -EINVAL,
+				"Input pin number out of range for pair (%d %d).", ain[0], ain[1]);
+		}
+
+		chan[chan_index] = ad7173_channel_template;
+		chan[chan_index].address = chan_index;
+		chan[chan_index].scan_index = chan_index;
+		chan[chan_index].channel = ain[0];
+		chan[chan_index].channel2 = ain[1];
+
+		channels_st_priv[chan_index].ain = AD7173_CH_ADDRESS(ain[0], ain[1]);
+		channels_st_priv[chan_index].chan_reg = chan_index;
+		channels_st_priv[chan_index].cfg.input_buf = true;
+		channels_st_priv[chan_index].cfg.odr = 0;
+
+		chan[chan_index].differential = fwnode_property_read_bool(child, "bipolar");
+		if (chan[chan_index].differential) {
+			chan[chan_index].info_mask_separate |= BIT(IIO_CHAN_INFO_OFFSET);
+			channels_st_priv[chan_index].cfg.bipolar = true;
+		}
+
+		chan_index++;
+	}
+
+	return 0;
+}
+
+static int ad7173_probe(struct spi_device *spi)
+{
+	struct ad7173_state *st;
+	struct iio_dev *indio_dev;
+	struct device *dev = &spi->dev;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*st));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	st = iio_priv(indio_dev);
+	st->info = device_get_match_data(dev);
+	if (!st->info)
+		return -ENODEV;
+
+	indio_dev->name = spi_get_device_id(spi)->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &ad7173_info;
+
+	spi->mode = SPI_MODE_3;
+
+	ad7173_sigma_delta_info.num_slots = st->info->num_configs;
+	ret = ad_sd_init(&st->sd, indio_dev, spi, &ad7173_sigma_delta_info);
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, indio_dev);
+
+	ret = ad7173_fw_parse_channel_config(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = devm_ad_sd_setup_buffer_and_trigger(dev, indio_dev);
+	if (ret)
+		return ret;
+
+	ret = ad7173_setup(indio_dev);
+	if (ret)
+		return ret;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret)
+		return ret;
+
+	if (IS_ENABLED(CONFIG_GPIOLIB))
+		return ad7173_gpio_init(st);
+
+	return 0;
+}
+
+static const struct of_device_id ad7173_of_match[] = {
+	{ .compatible = "adi,ad7172-2",
+	  .data = &ad7173_device_info[ID_AD7172_2], },
+	{ .compatible = "adi,ad7173-8",
+	  .data = &ad7173_device_info[ID_AD7173_8], },
+	{ .compatible = "adi,ad7175-2",
+	  .data = &ad7173_device_info[ID_AD7175_2], },
+	{ .compatible = "adi,ad7176-2",
+	  .data = &ad7173_device_info[ID_AD7176_2], },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ad7173_of_match);
+
+static const struct spi_device_id ad7173_id_table[] = {
+	{ "ad7172-2", (kernel_ulong_t)&ad7173_device_info[ID_AD7172_2], },
+	{ "ad7173-8", (kernel_ulong_t)&ad7173_device_info[ID_AD7173_8], },
+	{ "ad7175-2", (kernel_ulong_t)&ad7173_device_info[ID_AD7175_2], },
+	{ "ad7176-2", (kernel_ulong_t)&ad7173_device_info[ID_AD7176_2], },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ad7173_id_table);
+
+static struct spi_driver ad7173_driver = {
+	.driver = {
+		.name	= "ad7173",
+		.of_match_table = ad7173_of_match,
+	},
+	.probe		= ad7173_probe,
+	.id_table	= ad7173_id_table,
+};
+module_spi_driver(ad7173_driver);
+
+MODULE_AUTHOR("Lars-Peter Clausen <lars@metafo.de>");
+MODULE_AUTHOR("Dumitru Ceclan <dumitru.ceclan@analog.com>");
+MODULE_DESCRIPTION("Analog Devices AD7172/AD7173/AD7175/AD7176 ADC driver");
+MODULE_LICENSE("GPL");