[3/4] ARM: dts: motorola-mapphone: Move handset devices to a common file

Message ID	20231125094248.43537-3-tony@atomide.com
State	New
Headers	show Authentication-Results: smtp.subspace.kernel.org; dkim=pass (2048-bit key) header.d=atomide.com header.i=@atomide.com header.b="TLPhZAJg" From: Tony Lindgren <tony@atomide.com> To: linux-omap@vger.kernel.org Cc: =?utf-8?q?Beno=C3=AEt_Cousson?= <bcousson@baylibre.com>, Carl Philipp Klemm <philipp@uvos.xyz>, Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>, Merlijn Wajer <merlijn@wizzup.org>, Pavel Machek <pavel@ucw.cz>, Sebastian Reichel <sre@kernel.org>, devicetree@vger.kernel.org Subject: [PATCH 3/4] ARM: dts: motorola-mapphone: Move handset devices to a common file Date: Sat, 25 Nov 2023 11:42:47 +0200 Message-ID: <20231125094248.43537-3-tony@atomide.com> In-Reply-To: <20231125094248.43537-1-tony@atomide.com> References: <20231125094248.43537-1-tony@atomide.com> Precedence: bulk MIME-Version: 1.0 Content-Transfer-Encoding: 8bit
Series	[1/4] dt-bindings: omap: Add Motorola mapphone mz609 and mz617 tablets \| expand [1/4] dt-bindings: omap: Add Motorola mapphone mz609 and mz617 tablets [2/4] ARM: dts: motorola-mapphone: Move LCD to common file for xt875 and xt894 [3/4] ARM: dts: motorola-mapphone: Move handset devices to a common file [4/4] ARM: dts: motorola-mapphone: Add basic support for mz609 and mz617

diff --git a/arch/arm/boot/dts/ti/omap/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/ti/omap/motorola-mapphone-common.dtsi --- a/arch/arm/boot/dts/ti/omap/motorola-mapphone-common.dtsi +++ b/arch/arm/boot/dts/ti/omap/motorola-mapphone-common.dtsi @@ -54,35 +54,6 @@ hdmi_regulator: regulator-hdmi { regulator-always-on; }; - /* FS USB Host PHY on port 1 for mdm6600 */ - fsusb1_phy: usb-phy@1 { - compatible = "motorola,mapphone-mdm6600"; - pinctrl-0 = <&usb_mdm6600_pins>; - pinctrl-1 = <&usb_mdm6600_sleep_pins>; - pinctrl-names = "default", "sleep"; - enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; /* gpio_95 */ - power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54 */ - reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; /* gpio_49 */ - /* mode: gpio_148 gpio_149 */ - motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>, - <&gpio5 21 GPIO_ACTIVE_HIGH>; - /* cmd: gpio_103 gpio_104 gpio_142 */ - motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>, - <&gpio4 8 GPIO_ACTIVE_HIGH>, - <&gpio5 14 GPIO_ACTIVE_HIGH>; - /* status: gpio_52 gpio_53 gpio_55 */ - motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>, - <&gpio2 21 GPIO_ACTIVE_HIGH>, - <&gpio2 23 GPIO_ACTIVE_HIGH>; - #phy-cells = <0>; - }; - - /* HS USB host TLL nop-phy on port 2 for w3glte */ - hsusb2_phy: usb-phy@2 { - compatible = "usb-nop-xceiv"; - #phy-cells = <0>; - }; - /* This is probably coming straight from the battery.. */ wl12xx_vmmc: regulator-wl12xx { compatible = "regulator-fixed"; @@ -113,33 +84,6 @@ soundcard { dais = <&mcbsp2_port>, <&mcbsp3_port>; }; - - pwm8: pwm-8 { - pinctrl-names = "default"; - pinctrl-0 = <&vibrator_direction_pin>; - - compatible = "ti,omap-dmtimer-pwm"; - #pwm-cells = <3>; - ti,timers = <&timer8>; - ti,clock-source = <0x01>; - }; - - pwm9: pwm-9 { - pinctrl-names = "default"; - pinctrl-0 = <&vibrator_enable_pin>; - - compatible = "ti,omap-dmtimer-pwm"; - #pwm-cells = <3>; - ti,timers = <&timer9>; - ti,clock-source = <0x01>; - }; - - vibrator { - compatible = "pwm-vibrator"; - pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>; - pwm-names = "enable", "direction"; - direction-duty-cycle-ns = <10000000>; - }; }; &cpu_thermal { @@ -183,13 +127,6 @@ hdmi_out: endpoint { }; }; -/* Battery NVRAM on 1-wire handled by w1_ds250x driver */ -&hdqw1w { - pinctrl-0 = <&hdq_pins>; - pinctrl-names = "default"; - ti,mode = "1w"; -}; - &i2c1 { tmp105@48 { compatible = "ti,tmp105"; @@ -243,34 +180,6 @@ wlcore: wlcore@2 { }; }; -&i2c2 { - touchscreen@4a { - compatible = "atmel,maxtouch"; - reg = <0x4a>; - pinctrl-names = "default"; - pinctrl-0 = <&touchscreen_pins>; - - reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */ - - /* gpio_183 with sys_nirq2 pad as wakeup */ - interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>, - <&omap4_pmx_core 0x160>; - interrupt-names = "irq", "wakeup"; - wakeup-source; - }; - - isl29030@44 { - compatible = "isil,isl29030"; - reg = <0x44>; - - pinctrl-names = "default"; - pinctrl-0 = <&als_proximity_pins>; - - interrupt-parent = <&gpio6>; - interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */ - }; -}; - &omap4_pmx_core { /* hdmi_hpd.gpio_63 */ @@ -280,13 +189,6 @@ OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3) >; }; - hdq_pins: hdq-pins { - pinctrl-single,pins = < - /* 0x4a100120 hdq_sio.hdq_sio aa27 */ - OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0) - >; - }; - /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */ dss_hdmi_pins: dss-hdmi-pins { pinctrl-single,pins = < @@ -348,73 +250,6 @@ OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) >; }; - touchscreen_pins: touchscreen-pins { - pinctrl-single,pins = < - OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3) - OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3) - >; - }; - - als_proximity_pins: als-proximity-pins { - pinctrl-single,pins = < - OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3) - >; - }; - - usb_mdm6600_pins: usb-mdm6600-pins { - pinctrl-single,pins = < - /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */ - OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3) - - /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */ - OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) - - /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */ - OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3) - - /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */ - OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3) - - /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */ - OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3) - - /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */ - OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3) - - /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */ - OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) - - /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */ - OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) - - /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */ - OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3) - - /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */ - OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3) - - /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */ - OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3) - >; - }; - - /* Modem sleep pins to keep gpio_49 high with internal pull */ - usb_mdm6600_sleep_pins: usb-mdm6600-sleep-pins { - pinctrl-single,pins = < - OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3) - OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) - OMAP4_IOPAD(0x072, PIN_INPUT_PULLUP | MUX_MODE7) /* Keep gpio_49 reset high */ - OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3) - OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3) - OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3) - OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) - OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) - OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3) - OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3) - OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3) - >; - }; - usb_ulpi_pins: usb-ulpi-pins { pinctrl-single,pins = < OMAP4_IOPAD(0x196, MUX_MODE7) @@ -522,18 +357,6 @@ OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_clkx */ OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_fsx */ >; }; - - vibrator_direction_pin: vibrator-direction-pins { - pinctrl-single,pins = < - OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */ - >; - }; - - vibrator_enable_pin: vibrator-enable-pins { - pinctrl-single,pins = < - OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */ - >; - }; }; &omap4_pmx_wkup { @@ -550,17 +373,6 @@ &rng_target { status = "disabled"; }; -/* Configure pwm clock source for timers 8 & 9 */ -&timer8 { - assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>; - assigned-clock-parents = <&sys_32k_ck>; -}; - -&timer9 { - assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>; - assigned-clock-parents = <&sys_32k_ck>; -}; - /* * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149 * for wake-up events for both the USB PHY and the UART. We can use gpio_149 @@ -593,20 +405,6 @@ bluetooth { }; }; -&usbhsohci { - phys = <&fsusb1_phy>; - phy-names = "usb"; -}; - -&usbhsehci { - phys = <&hsusb2_phy>; -}; - -&usbhshost { - port1-mode = "ohci-phy-4pin-dpdm"; - port2-mode = "ehci-tll"; -}; - /* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */ &usb_otg_hs { interface-type = <1>; @@ -619,23 +417,6 @@ &usb_otg_hs { power = <150>; }; -&i2c4 { - ak8975: magnetometer@c { - compatible = "asahi-kasei,ak8975"; - reg = <0x0c>; - - vdd-supply = <&vhvio>; - - interrupt-parent = <&gpio6>; - interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */ - - rotation-matrix = "-1", "0", "0", - "0", "1", "0", - "0", "0", "-1"; - - }; -}; - &mcbsp2 { #sound-dai-cells = <0>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/ti/omap/motorola-mapphone-handset.dtsi b/arch/arm/boot/dts/ti/omap/motorola-mapphone-handset.dtsi new file mode 100644 --- /dev/null +++ b/arch/arm/boot/dts/ti/omap/motorola-mapphone-handset.dtsi @@ -0,0 +1,234 @@ +// SPDX-License-Identifier: GPL-2.0-only +/dts-v1/; + +#include "motorola-mapphone-common.dtsi" + +/ { + /* FS USB Host PHY on port 1 for mdm6600 */ + fsusb1_phy: usb-phy@1 { + compatible = "motorola,mapphone-mdm6600"; + pinctrl-0 = <&usb_mdm6600_pins>; + pinctrl-1 = <&usb_mdm6600_sleep_pins>; + pinctrl-names = "default", "sleep"; + enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; /* gpio_95 */ + power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54 */ + reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; /* gpio_49 */ + /* mode: gpio_148 gpio_149 */ + motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>, + <&gpio5 21 GPIO_ACTIVE_HIGH>; + /* cmd: gpio_103 gpio_104 gpio_142 */ + motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>, + <&gpio4 8 GPIO_ACTIVE_HIGH>, + <&gpio5 14 GPIO_ACTIVE_HIGH>; + /* status: gpio_52 gpio_53 gpio_55 */ + motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>, + <&gpio2 21 GPIO_ACTIVE_HIGH>, + <&gpio2 23 GPIO_ACTIVE_HIGH>; + #phy-cells = <0>; + }; + + /* HS USB host TLL nop-phy on port 2 for w3glte */ + hsusb2_phy: usb-phy@2 { + compatible = "usb-nop-xceiv"; + #phy-cells = <0>; + }; + + pwm8: pwm-8 { + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_direction_pin>; + + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&timer8>; + ti,clock-source = <0x01>; + }; + + pwm9: pwm-9 { + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_enable_pin>; + + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&timer9>; + ti,clock-source = <0x01>; + }; + + vibrator { + compatible = "pwm-vibrator"; + pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>; + pwm-names = "enable", "direction"; + direction-duty-cycle-ns = <10000000>; + }; +}; + +/* Battery NVRAM on 1-wire handled by w1_ds250x driver */ +&hdqw1w { + pinctrl-0 = <&hdq_pins>; + pinctrl-names = "default"; + ti,mode = "1w"; +}; + +&i2c2 { + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + pinctrl-names = "default"; + pinctrl-0 = <&touchscreen_pins>; + + reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */ + + /* gpio_183 with sys_nirq2 pad as wakeup */ + interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>, + <&omap4_pmx_core 0x160>; + interrupt-names = "irq", "wakeup"; + wakeup-source; + }; + + isl29030@44 { + compatible = "isil,isl29030"; + reg = <0x44>; + + pinctrl-names = "default"; + pinctrl-0 = <&als_proximity_pins>; + + interrupt-parent = <&gpio6>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */ + }; +}; + +&omap4_pmx_core { + hdq_pins: hdq-pins { + pinctrl-single,pins = < + /* 0x4a100120 hdq_sio.hdq_sio aa27 */ + OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0) + >; + }; + + /* kpd_row0.gpio_178 */ + tmp105_irq: tmp105-irq-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3) + >; + }; + + touchscreen_pins: touchscreen-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3) + OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3) + >; + }; + + usb_mdm6600_pins: usb-mdm6600-pins { + pinctrl-single,pins = < + /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */ + OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3) + + /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */ + OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) + + /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */ + OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3) + + /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */ + OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3) + + /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */ + OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3) + + /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */ + OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3) + + /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */ + OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) + + /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */ + OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) + + /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */ + OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3) + + /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */ + OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3) + + /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */ + OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3) + >; + }; + + /* Modem sleep pins to keep gpio_49 high with internal pull */ + usb_mdm6600_sleep_pins: usb-mdm6600-sleep-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3) + OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) + OMAP4_IOPAD(0x072, PIN_INPUT_PULLUP | MUX_MODE7) /* Keep gpio_49 reset high */ + OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3) + OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3) + OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3) + OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) + OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) + OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3) + OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3) + OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3) + >; + }; + + als_proximity_pins: als-proximity-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3) + >; + }; + + vibrator_direction_pin: vibrator-direction-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */ + >; + }; + + vibrator_enable_pin: vibrator-enable-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */ + >; + }; +}; + +/* Configure pwm clock source for timers 8 & 9 */ +&timer8 { + assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>; + assigned-clock-parents = <&sys_32k_ck>; +}; + +&timer9 { + assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>; + assigned-clock-parents = <&sys_32k_ck>; +}; + +&usbhsohci { + phys = <&fsusb1_phy>; + phy-names = "usb"; +}; + +&usbhsehci { + phys = <&hsusb2_phy>; +}; + +&usbhshost { + port1-mode = "ohci-phy-4pin-dpdm"; + port2-mode = "ehci-tll"; +}; + +&i2c4 { + ak8975: magnetometer@c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + + vdd-supply = <&vhvio>; + + interrupt-parent = <&gpio6>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */ + + rotation-matrix = "-1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; + + }; +}; diff --git a/arch/arm/boot/dts/ti/omap/motorola-mapphone-xt8xx.dtsi b/arch/arm/boot/dts/ti/omap/motorola-mapphone-xt8xx.dtsi --- a/arch/arm/boot/dts/ti/omap/motorola-mapphone-xt8xx.dtsi +++ b/arch/arm/boot/dts/ti/omap/motorola-mapphone-xt8xx.dtsi @@ -1,7 +1,7 @@ // SPDX-License-Identifier: GPL-2.0-only /dts-v1/; -#include "motorola-mapphone-common.dtsi" +#include "motorola-mapphone-handset.dtsi" / { backlight: backlight {

[3/4] ARM: dts: motorola-mapphone: Move handset devices to a common file

Commit Message

Patch