@@ -647,23 +647,6 @@ static int at803x_parse_dt(struct phy_device *phydev)
priv->clk_25m_reg |= FIELD_PREP(AT803X_CLK_OUT_MASK, sel);
priv->clk_25m_mask |= AT803X_CLK_OUT_MASK;
-
- /* Fixup for the AR8030/AR8035. This chip has another mask and
- * doesn't support the DSP reference. Eg. the lowest bit of the
- * mask. The upper two bits select the same frequencies. Mask
- * the lowest bit here.
- *
- * Warning:
- * There was no datasheet for the AR8030 available so this is
- * just a guess. But the AR8035 is listed as pin compatible
- * to the AR8030 so there might be a good chance it works on
- * the AR8030 too.
- */
- if (phydev->drv->phy_id == ATH8030_PHY_ID ||
- phydev->drv->phy_id == ATH8035_PHY_ID) {
- priv->clk_25m_reg &= AT8035_CLK_OUT_MASK;
- priv->clk_25m_mask &= AT8035_CLK_OUT_MASK;
- }
}
ret = of_property_read_u32(node, "qca,clk-out-strength", &strength);
@@ -1681,6 +1664,47 @@ static int at8031_set_wol(struct phy_device *phydev,
return at803x_set_wol(phydev, wol);
}
+static int at8035_parse_dt(struct phy_device *phydev)
+{
+ struct device_node *node = phydev->mdio.dev.of_node;
+ struct at803x_priv *priv = phydev->priv;
+ u32 freq;
+ int ret;
+
+ if (!IS_ENABLED(CONFIG_OF_MDIO))
+ return 0;
+
+ ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq);
+ if (!ret) {
+ /* Fixup for the AR8030/AR8035. This chip has another mask and
+ * doesn't support the DSP reference. Eg. the lowest bit of the
+ * mask. The upper two bits select the same frequencies. Mask
+ * the lowest bit here.
+ *
+ * Warning:
+ * There was no datasheet for the AR8030 available so this is
+ * just a guess. But the AR8035 is listed as pin compatible
+ * to the AR8030 so there might be a good chance it works on
+ * the AR8030 too.
+ */
+ priv->clk_25m_reg &= AT8035_CLK_OUT_MASK;
+ priv->clk_25m_mask &= AT8035_CLK_OUT_MASK;
+ }
+
+ return 0;
+}
+
+static int at8035_probe(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = at803x_probe(phydev);
+ if (ret)
+ return ret;
+
+ return at8035_parse_dt(phydev);
+}
+
static int qca83xx_probe(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
@@ -2167,7 +2191,7 @@ static struct phy_driver at803x_driver[] = {
PHY_ID_MATCH_EXACT(ATH8035_PHY_ID),
.name = "Qualcomm Atheros AR8035",
.flags = PHY_POLL_CABLE_TEST,
- .probe = at803x_probe,
+ .probe = at8035_probe,
.config_aneg = at803x_config_aneg,
.config_init = at803x_config_init,
.soft_reset = genphy_soft_reset,
@@ -2188,7 +2212,7 @@ static struct phy_driver at803x_driver[] = {
.phy_id = ATH8030_PHY_ID,
.name = "Qualcomm Atheros AR8030",
.phy_id_mask = AT8030_PHY_ID_MASK,
- .probe = at803x_probe,
+ .probe = at8035_probe,
.config_init = at803x_config_init,
.link_change_notify = at803x_link_change_notify,
.set_wol = at803x_set_wol,
Move at8035 specific DT parse for clock out frequency to dedicated probe to make at803x probe function more generic. This is to tidy code and no behaviour change are intended. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> --- drivers/net/phy/at803x.c | 62 ++++++++++++++++++++++++++++------------ 1 file changed, 43 insertions(+), 19 deletions(-)