diff mbox series

[v2,1/4] arm64: dts: qcom: sm8450: move Soundwire pinctrl to its nodes

Message ID 20231213162856.188566-2-krzysztof.kozlowski@linaro.org
State New
Headers show
Series [v2,1/4] arm64: dts: qcom: sm8450: move Soundwire pinctrl to its nodes | expand

Commit Message

Krzysztof Kozlowski Dec. 13, 2023, 4:28 p.m. UTC
Pin configuration for Soundwire bus should be set in Soundwire
controller nodes, not in the associated macro codec node.  This
placement change should not have big impact in general, because macro
codec is a clock provider for Soundwire controller, thus its devices is
probed first.  However it will have impact for disabled Soundwire buses,
e.g. WSA2, because after this change the pins will be left in default
state.

We also follow similar approach in newer SoCs, like Qualcomm SM8650.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---

Not tested on HW.
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 12e55a0c7417..3b6ea9653d2a 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2160,8 +2160,6 @@  wsa2macro: codec@31e0000 {
 
 			#clock-cells = <0>;
 			clock-output-names = "wsa2-mclk";
-			pinctrl-names = "default";
-			pinctrl-0 = <&wsa2_swr_active>;
 			#sound-dai-cells = <1>;
 		};
 
@@ -2173,6 +2171,9 @@  swr4: soundwire-controller@31f0000 {
 			clock-names = "iface";
 			label = "WSA2";
 
+			pinctrl-0 = <&wsa2_swr_active>;
+			pinctrl-names = "default";
+
 			qcom,din-ports = <2>;
 			qcom,dout-ports = <6>;
 
@@ -2208,8 +2209,6 @@  rxmacro: codec@3200000 {
 
 			#clock-cells = <0>;
 			clock-output-names = "mclk";
-			pinctrl-names = "default";
-			pinctrl-0 = <&rx_swr_active>;
 			#sound-dai-cells = <1>;
 		};
 
@@ -2223,6 +2222,9 @@  swr1: soundwire-controller@3210000 {
 			qcom,din-ports = <0>;
 			qcom,dout-ports = <5>;
 
+			pinctrl-0 = <&rx_swr_active>;
+			pinctrl-names = "default";
+
 			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
 			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x00>;
 			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
@@ -2254,8 +2256,6 @@  txmacro: codec@3220000 {
 
 			#clock-cells = <0>;
 			clock-output-names = "mclk";
-			pinctrl-names = "default";
-			pinctrl-0 = <&tx_swr_active>;
 			#sound-dai-cells = <1>;
 		};
 
@@ -2275,8 +2275,6 @@  wsamacro: codec@3240000 {
 
 			#clock-cells = <0>;
 			clock-output-names = "mclk";
-			pinctrl-names = "default";
-			pinctrl-0 = <&wsa_swr_active>;
 			#sound-dai-cells = <1>;
 		};
 
@@ -2288,6 +2286,9 @@  swr0: soundwire-controller@3250000 {
 			clock-names = "iface";
 			label = "WSA";
 
+			pinctrl-0 = <&wsa_swr_active>;
+			pinctrl-names = "default";
+
 			qcom,din-ports = <2>;
 			qcom,dout-ports = <6>;
 
@@ -2318,6 +2319,9 @@  swr2: soundwire-controller@33b0000 {
 			clock-names = "iface";
 			label = "TX";
 
+			pinctrl-0 = <&tx_swr_active>;
+			pinctrl-names = "default";
+
 			qcom,din-ports = <4>;
 			qcom,dout-ports = <0>;
 			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x01 0x03 0x03>;