[v2] dt-bindings: regulator: Convert ti,tps65132 to YAML

diff --git a/Documentation/devicetree/bindings/regulator/ti,tps65132.yaml b/Documentation/devicetree/bindings/regulator/ti,tps65132.yaml
new file mode 100644
index 000000000000..6a6d1a3d6fa7
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/ti,tps65132.yaml
@@ -0,0 +1,84 @@ 
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/ti,tps65132.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI TPS65132 Dual Output Power Regulators
+
+maintainers:
+  - devicetree@vger.kernel.org
+
+description: |
+  The TPS65132 is designed to supply positive/negative driven applications.
+
+  Datasheet is available at:
+  https://www.ti.com/lit/gpn/tps65132
+
+properties:
+  compatible:
+    enum:
+      - ti,tps65132
+
+  reg:
+    maxItems: 1
+
+patternProperties:
+  "^out[pn]$":
+    type: object
+    $ref: regulator.yaml#
+    unevaluatedProperties: false
+    description:
+      Properties for single regulator.
+
+    properties:
+      enable-gpios:
+        maxItems: 1
+        description:
+          GPIO specifier to enable the GPIO control (on/off) for regulator.
+
+      active-discharge-gpios:
+        maxItems: 1
+        description:
+          GPIO specifier to actively discharge the delay mechanism.
+
+      ti,active-discharge-time-us:
+        description: Regulator active discharge time in microseconds.
+
+    dependencies:
+      active-discharge-gpios: [ 'ti,active-discharge-time-us' ]
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        regulator@3e {
+            compatible = "ti,tps65132";
+            reg = <0x3e>;
+
+            outp {
+                regulator-name = "outp";
+                regulator-boot-on;
+                regulator-always-on;
+                enable-gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+            };
+
+            outn {
+                regulator-name = "outn";
+                regulator-boot-on;
+                regulator-always-on;
+                regulator-active-discharge = <0>;
+                enable-gpios = <&gpio 40 GPIO_ACTIVE_HIGH>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/regulator/tps65132-regulator.txt b/Documentation/devicetree/bindings/regulator/tps65132-regulator.txt
deleted file mode 100644
index 3a3505520c69..000000000000
--- a/Documentation/devicetree/bindings/regulator/tps65132-regulator.txt
+++ /dev/null
@@ -1,46 +0,0 @@ 
-TPS65132 regulators
-
-Required properties:
-- compatible: "ti,tps65132"
-- reg: I2C slave address
-
-Optional Subnode:
-Device supports two regulators OUTP and OUTN. A sub node within the
-   device node describe the properties of these regulators. The sub-node
-   names must be as follows:
-	-For regulator outp, the sub node name should be "outp".
-	-For regulator outn, the sub node name should be "outn".
-
--enable-gpios:(active high, output) Regulators are controlled by the input pins.
-   If it is connected to GPIO through host system then provide the
-   gpio number as per gpio.txt.
--active-discharge-gpios: (active high, output) Some configurations use delay mechanisms
-  on the enable pin, to keep the regulator enabled for some time after
-  the enable signal goes low. This GPIO is used to actively discharge
-  the delay mechanism. Requires specification of ti,active-discharge-time-us
--ti,active-discharge-time-us: how long the active discharge gpio should be
-  asserted for during active discharge, in microseconds.
-
-Each regulator is defined using the standard binding for regulators.
-
-Example:
-
-	tps65132@3e {
-		compatible = "ti,tps65132";
-		reg = <0x3e>;
-
-		outp {
-			regulator-name = "outp";
-			regulator-boot-on;
-			regulator-always-on;
-			enable-gpios = <&gpio 23 0>;
-		};
-
-		outn {
-			regulator-name = "outn";
-			regulator-boot-on;
-			regulator-always-on;
-			regulator-active-discharge = <0>;
-			enable-gpios = <&gpio 40 0>;
-		};
-	};