diff mbox

[edk2,v3,10/10] PL180: update for indentifying SD

Message ID 1474470147-23156-11-git-send-email-haojian.zhuang@linaro.org
State Superseded
Headers show

Commit Message

Haojian Zhuang Sept. 21, 2016, 3:02 p.m. UTC 
When CMD6 & ACMD51 are added into indentifying SD process, PL180
should also support CMD6 & ACMD51. Otherwise, it'll hang when
system tries to read expected data.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

---
 ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

-- 
2.7.4

_______________________________________________
edk2-devel mailing list
edk2-devel@lists.01.org
https://lists.01.org/mailman/listinfo/edk2-devel
diff mbox

Patch

diff --git a/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c b/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c
index 5526aac..7647608 100644
--- a/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c
+++ b/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c
@@ -126,6 +126,15 @@  MciSendCommand (
     MciPrepareDataPath (MCI_DATACTL_CARD_TO_CONT);
   } else if ((MmcCmd == MMC_CMD24) || (MmcCmd == MMC_CMD20)) {
     MciPrepareDataPath (MCI_DATACTL_CONT_TO_CARD);
+  } else if (MmcCmd == MMC_CMD6) {
+    MmioWrite32 (MCI_DATA_TIMER_REG, 0xFFFFFFF);
+    MmioWrite32 (MCI_DATA_LENGTH_REG, 64);
+    MmioWrite32 (MCI_DATA_CTL_REG, MCI_DATACTL_ENABLE | MCI_DATACTL_CARD_TO_CONT | MCI_DATACTL_STREAM_TRANS);
+  } else if (MmcCmd == MMC_ACMD51) {
+    MmioWrite32 (MCI_DATA_TIMER_REG, 0xFFFFFFF);
+    /* SCR register is 8 bytes long. */
+    MmioWrite32 (MCI_DATA_LENGTH_REG, 8);
+    MmioWrite32 (MCI_DATA_CTL_REG, MCI_DATACTL_ENABLE | MCI_DATACTL_CARD_TO_CONT | MCI_DATACTL_STREAM_TRANS);
   }
 
   // Create Command for PL180
@@ -223,7 +232,11 @@  MciReadBlockData (
 
   // Read data from the RX FIFO
   Loop   = 0;
-  Finish = MMCI0_BLOCKLEN / 4;
+  if (Length < MMCI0_BLOCKLEN) {
+    Finish = Length / 4;
+  } else {
+    Finish = MMCI0_BLOCKLEN / 4;
+  }
 
   // Raise the TPL at the highest level to disable Interrupts.
   Tpl = gBS->RaiseTPL (TPL_HIGH_LEVEL);