@@ -24,65 +24,11 @@
#include "qcom.h"
-#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10
-#define AT803X_SFC_ASSERT_CRS BIT(11)
-#define AT803X_SFC_FORCE_LINK BIT(10)
-#define AT803X_SFC_MDI_CROSSOVER_MODE_M GENMASK(6, 5)
-#define AT803X_SFC_AUTOMATIC_CROSSOVER 0x3
-#define AT803X_SFC_MANUAL_MDIX 0x1
-#define AT803X_SFC_MANUAL_MDI 0x0
-#define AT803X_SFC_SQE_TEST BIT(2)
-#define AT803X_SFC_POLARITY_REVERSAL BIT(1)
-#define AT803X_SFC_DISABLE_JABBER BIT(0)
-
-#define AT803X_SPECIFIC_STATUS 0x11
-#define AT803X_SS_SPEED_MASK GENMASK(15, 14)
-#define AT803X_SS_SPEED_1000 2
-#define AT803X_SS_SPEED_100 1
-#define AT803X_SS_SPEED_10 0
-#define AT803X_SS_DUPLEX BIT(13)
-#define AT803X_SS_SPEED_DUPLEX_RESOLVED BIT(11)
-#define AT803X_SS_MDIX BIT(6)
-
-#define QCA808X_SS_SPEED_MASK GENMASK(9, 7)
-#define QCA808X_SS_SPEED_2500 4
-
-#define AT803X_INTR_ENABLE 0x12
-#define AT803X_INTR_ENABLE_AUTONEG_ERR BIT(15)
-#define AT803X_INTR_ENABLE_SPEED_CHANGED BIT(14)
-#define AT803X_INTR_ENABLE_DUPLEX_CHANGED BIT(13)
-#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
-#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
-#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
-#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
-#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
-#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
-#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
-#define AT803X_INTR_ENABLE_WOL BIT(0)
-
-#define AT803X_INTR_STATUS 0x13
-
-#define AT803X_SMART_SPEED 0x14
-#define AT803X_SMART_SPEED_ENABLE BIT(5)
-#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK GENMASK(4, 2)
-#define AT803X_SMART_SPEED_BYPASS_TIMER BIT(1)
-#define AT803X_CDT 0x16
-#define AT803X_CDT_MDI_PAIR_MASK GENMASK(9, 8)
-#define AT803X_CDT_ENABLE_TEST BIT(0)
-#define AT803X_CDT_STATUS 0x1c
-#define AT803X_CDT_STATUS_STAT_NORMAL 0
-#define AT803X_CDT_STATUS_STAT_SHORT 1
-#define AT803X_CDT_STATUS_STAT_OPEN 2
-#define AT803X_CDT_STATUS_STAT_FAIL 3
-#define AT803X_CDT_STATUS_STAT_MASK GENMASK(9, 8)
-#define AT803X_CDT_STATUS_DELTA_TIME_MASK GENMASK(7, 0)
#define AT803X_LED_CONTROL 0x18
#define AT803X_PHY_MMD3_WOL_CTRL 0x8012
#define AT803X_WOL_EN BIT(5)
-#define AT803X_LOC_MAC_ADDR_0_15_OFFSET 0x804C
-#define AT803X_LOC_MAC_ADDR_16_31_OFFSET 0x804B
-#define AT803X_LOC_MAC_ADDR_32_47_OFFSET 0x804A
+
#define AT803X_REG_CHIP_CONFIG 0x1f
#define AT803X_BT_BX_REG_SEL 0x8000
@@ -138,10 +84,6 @@
#define AT803X_CLK_OUT_STRENGTH_HALF 1
#define AT803X_CLK_OUT_STRENGTH_QUARTER 2
-#define AT803X_DEFAULT_DOWNSHIFT 5
-#define AT803X_MIN_DOWNSHIFT 2
-#define AT803X_MAX_DOWNSHIFT 9
-
#define AT803X_MMD3_SMARTEEE_CTL1 0x805b
#define AT803X_MMD3_SMARTEEE_CTL2 0x805c
#define AT803X_MMD3_SMARTEEE_CTL3 0x805d
@@ -158,6 +100,8 @@
#define QCA9561_PHY_ID 0x004dd042
+#define AT803X_SS_SPEED_MASK GENMASK(15, 14)
+
#define AT803X_PAGE_FIBER 0
#define AT803X_PAGE_COPPER 1
@@ -366,11 +310,6 @@ MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
MODULE_AUTHOR("Matus Ujhelyi");
MODULE_LICENSE("GPL");
-struct at803x_ss_mask {
- u16 speed_mask;
- u8 speed_shift;
-};
-
struct at803x_priv {
int flags;
u16 clk_25m_reg;
@@ -470,80 +409,6 @@ static void at803x_context_restore(struct phy_device *phydev,
phy_write(phydev, AT803X_LED_CONTROL, context->led_control);
}
-static int at803x_set_wol(struct phy_device *phydev,
- struct ethtool_wolinfo *wol)
-{
- int ret, irq_enabled;
-
- if (wol->wolopts & WAKE_MAGIC) {
- struct net_device *ndev = phydev->attached_dev;
- const u8 *mac;
- unsigned int i;
- static const unsigned int offsets[] = {
- AT803X_LOC_MAC_ADDR_32_47_OFFSET,
- AT803X_LOC_MAC_ADDR_16_31_OFFSET,
- AT803X_LOC_MAC_ADDR_0_15_OFFSET,
- };
-
- if (!ndev)
- return -ENODEV;
-
- mac = (const u8 *)ndev->dev_addr;
-
- if (!is_valid_ether_addr(mac))
- return -EINVAL;
-
- for (i = 0; i < 3; i++)
- phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
- mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
-
- /* Enable WOL interrupt */
- ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
- if (ret)
- return ret;
- } else {
- /* Disable WOL interrupt */
- ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
- if (ret)
- return ret;
- }
-
- /* Clear WOL status */
- ret = phy_read(phydev, AT803X_INTR_STATUS);
- if (ret < 0)
- return ret;
-
- /* Check if there are other interrupts except for WOL triggered when PHY is
- * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can
- * be passed up to the interrupt PIN.
- */
- irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
- if (irq_enabled < 0)
- return irq_enabled;
-
- irq_enabled &= ~AT803X_INTR_ENABLE_WOL;
- if (ret & irq_enabled && !phy_polling_mode(phydev))
- phy_trigger_machine(phydev);
-
- return 0;
-}
-
-static void at803x_get_wol(struct phy_device *phydev,
- struct ethtool_wolinfo *wol)
-{
- int value;
-
- wol->supported = WAKE_MAGIC;
- wol->wolopts = 0;
-
- value = phy_read(phydev, AT803X_INTR_ENABLE);
- if (value < 0)
- return;
-
- if (value & AT803X_INTR_ENABLE_WOL)
- wol->wolopts |= WAKE_MAGIC;
-}
-
static int at803x_suspend(struct phy_device *phydev)
{
int value;
@@ -816,73 +681,6 @@ static int at803x_config_init(struct phy_device *phydev)
return phy_modify(phydev, MII_ADVERTISE, MDIO_AN_CTRL1_XNP, 0);
}
-static int at803x_ack_interrupt(struct phy_device *phydev)
-{
- int err;
-
- err = phy_read(phydev, AT803X_INTR_STATUS);
-
- return (err < 0) ? err : 0;
-}
-
-static int at803x_config_intr(struct phy_device *phydev)
-{
- int err;
- int value;
-
- value = phy_read(phydev, AT803X_INTR_ENABLE);
-
- if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
- /* Clear any pending interrupts */
- err = at803x_ack_interrupt(phydev);
- if (err)
- return err;
-
- value |= AT803X_INTR_ENABLE_AUTONEG_ERR;
- value |= AT803X_INTR_ENABLE_SPEED_CHANGED;
- value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
- value |= AT803X_INTR_ENABLE_LINK_FAIL;
- value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
-
- err = phy_write(phydev, AT803X_INTR_ENABLE, value);
- } else {
- err = phy_write(phydev, AT803X_INTR_ENABLE, 0);
- if (err)
- return err;
-
- /* Clear any pending interrupts */
- err = at803x_ack_interrupt(phydev);
- }
-
- return err;
-}
-
-static irqreturn_t at803x_handle_interrupt(struct phy_device *phydev)
-{
- int irq_status, int_enabled;
-
- irq_status = phy_read(phydev, AT803X_INTR_STATUS);
- if (irq_status < 0) {
- phy_error(phydev);
- return IRQ_NONE;
- }
-
- /* Read the current enabled interrupts */
- int_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
- if (int_enabled < 0) {
- phy_error(phydev);
- return IRQ_NONE;
- }
-
- /* See if this was one of our enabled interrupts */
- if (!(irq_status & int_enabled))
- return IRQ_NONE;
-
- phy_trigger_machine(phydev);
-
- return IRQ_HANDLED;
-}
-
static void at803x_link_change_notify(struct phy_device *phydev)
{
/*
@@ -908,69 +706,6 @@ static void at803x_link_change_notify(struct phy_device *phydev)
}
}
-static int at803x_read_specific_status(struct phy_device *phydev,
- struct at803x_ss_mask ss_mask)
-{
- int ss;
-
- /* Read the AT8035 PHY-Specific Status register, which indicates the
- * speed and duplex that the PHY is actually using, irrespective of
- * whether we are in autoneg mode or not.
- */
- ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
- if (ss < 0)
- return ss;
-
- if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
- int sfc, speed;
-
- sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL);
- if (sfc < 0)
- return sfc;
-
- speed = ss & ss_mask.speed_mask;
- speed >>= ss_mask.speed_shift;
-
- switch (speed) {
- case AT803X_SS_SPEED_10:
- phydev->speed = SPEED_10;
- break;
- case AT803X_SS_SPEED_100:
- phydev->speed = SPEED_100;
- break;
- case AT803X_SS_SPEED_1000:
- phydev->speed = SPEED_1000;
- break;
- case QCA808X_SS_SPEED_2500:
- phydev->speed = SPEED_2500;
- break;
- }
- if (ss & AT803X_SS_DUPLEX)
- phydev->duplex = DUPLEX_FULL;
- else
- phydev->duplex = DUPLEX_HALF;
-
- if (ss & AT803X_SS_MDIX)
- phydev->mdix = ETH_TP_MDI_X;
- else
- phydev->mdix = ETH_TP_MDI;
-
- switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) {
- case AT803X_SFC_MANUAL_MDI:
- phydev->mdix_ctrl = ETH_TP_MDI;
- break;
- case AT803X_SFC_MANUAL_MDIX:
- phydev->mdix_ctrl = ETH_TP_MDI_X;
- break;
- case AT803X_SFC_AUTOMATIC_CROSSOVER:
- phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
- break;
- }
- }
-
- return 0;
-}
-
static int at803x_read_status(struct phy_device *phydev)
{
struct at803x_ss_mask ss_mask = { 0 };
@@ -1006,50 +741,6 @@ static int at803x_read_status(struct phy_device *phydev)
return 0;
}
-static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
-{
- u16 val;
-
- switch (ctrl) {
- case ETH_TP_MDI:
- val = AT803X_SFC_MANUAL_MDI;
- break;
- case ETH_TP_MDI_X:
- val = AT803X_SFC_MANUAL_MDIX;
- break;
- case ETH_TP_MDI_AUTO:
- val = AT803X_SFC_AUTOMATIC_CROSSOVER;
- break;
- default:
- return 0;
- }
-
- return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL,
- AT803X_SFC_MDI_CROSSOVER_MODE_M,
- FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val));
-}
-
-static int at803x_prepare_config_aneg(struct phy_device *phydev)
-{
- int ret;
-
- ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
- if (ret < 0)
- return ret;
-
- /* Changes of the midx bits are disruptive to the normal operation;
- * therefore any changes to these registers must be followed by a
- * software reset to take effect.
- */
- if (ret == 1) {
- ret = genphy_soft_reset(phydev);
- if (ret < 0)
- return ret;
- }
-
- return 0;
-}
-
static int at803x_config_aneg(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
@@ -1065,80 +756,6 @@ static int at803x_config_aneg(struct phy_device *phydev)
return genphy_config_aneg(phydev);
}
-static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
-{
- int val;
-
- val = phy_read(phydev, AT803X_SMART_SPEED);
- if (val < 0)
- return val;
-
- if (val & AT803X_SMART_SPEED_ENABLE)
- *d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2;
- else
- *d = DOWNSHIFT_DEV_DISABLE;
-
- return 0;
-}
-
-static int at803x_set_downshift(struct phy_device *phydev, u8 cnt)
-{
- u16 mask, set;
- int ret;
-
- switch (cnt) {
- case DOWNSHIFT_DEV_DEFAULT_COUNT:
- cnt = AT803X_DEFAULT_DOWNSHIFT;
- fallthrough;
- case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT:
- set = AT803X_SMART_SPEED_ENABLE |
- AT803X_SMART_SPEED_BYPASS_TIMER |
- FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2);
- mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK;
- break;
- case DOWNSHIFT_DEV_DISABLE:
- set = 0;
- mask = AT803X_SMART_SPEED_ENABLE |
- AT803X_SMART_SPEED_BYPASS_TIMER;
- break;
- default:
- return -EINVAL;
- }
-
- ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set);
-
- /* After changing the smart speed settings, we need to perform a
- * software reset, use phy_init_hw() to make sure we set the
- * reapply any values which might got lost during software reset.
- */
- if (ret == 1)
- ret = phy_init_hw(phydev);
-
- return ret;
-}
-
-static int at803x_get_tunable(struct phy_device *phydev,
- struct ethtool_tunable *tuna, void *data)
-{
- switch (tuna->id) {
- case ETHTOOL_PHY_DOWNSHIFT:
- return at803x_get_downshift(phydev, data);
- default:
- return -EOPNOTSUPP;
- }
-}
-
-static int at803x_set_tunable(struct phy_device *phydev,
- struct ethtool_tunable *tuna, const void *data)
-{
- switch (tuna->id) {
- case ETHTOOL_PHY_DOWNSHIFT:
- return at803x_set_downshift(phydev, *(const u8 *)data);
- default:
- return -EOPNOTSUPP;
- }
-}
-
static int at803x_cable_test_result_trans(u16 status)
{
switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) {
@@ -1170,45 +787,6 @@ static bool at803x_cdt_fault_length_valid(u16 status)
return false;
}
-static int at803x_cdt_fault_length(int dt)
-{
- /* According to the datasheet the distance to the fault is
- * DELTA_TIME * 0.824 meters.
- *
- * The author suspect the correct formula is:
- *
- * fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2
- *
- * where c is the speed of light, VF is the velocity factor of
- * the twisted pair cable, 125MHz the counter frequency and
- * we need to divide by 2 because the hardware will measure the
- * round trip time to the fault and back to the PHY.
- *
- * With a VF of 0.69 we get the factor 0.824 mentioned in the
- * datasheet.
- */
- return (dt * 824) / 10;
-}
-
-static int at803x_cdt_start(struct phy_device *phydev,
- u32 cdt_start)
-{
- return phy_write(phydev, AT803X_CDT, cdt_start);
-}
-
-static int at803x_cdt_wait_for_completion(struct phy_device *phydev,
- u32 cdt_en)
-{
- int val, ret;
-
- /* One test run takes about 25ms */
- ret = phy_read_poll_timeout(phydev, AT803X_CDT, val,
- !(val & cdt_en),
- 30000, 100000, true);
-
- return ret < 0 ? ret : 0;
-}
-
static int at803x_cable_test_one_pair(struct phy_device *phydev, int pair)
{
static const int ethtool_pair[] = {
@@ -3,6 +3,9 @@
#include <linux/phy.h>
#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+
#include "qcom.h"
MODULE_DESCRIPTION("Qualcomm PHY driver Common Functions");
@@ -51,3 +54,376 @@ int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data)
return phy_write(phydev, AT803X_DEBUG_DATA, data);
}
EXPORT_SYMBOL_GPL(at803x_debug_reg_write);
+
+int at803x_set_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol)
+{
+ int ret, irq_enabled;
+
+ if (wol->wolopts & WAKE_MAGIC) {
+ struct net_device *ndev = phydev->attached_dev;
+ const u8 *mac;
+ unsigned int i;
+ static const unsigned int offsets[] = {
+ AT803X_LOC_MAC_ADDR_32_47_OFFSET,
+ AT803X_LOC_MAC_ADDR_16_31_OFFSET,
+ AT803X_LOC_MAC_ADDR_0_15_OFFSET,
+ };
+
+ if (!ndev)
+ return -ENODEV;
+
+ mac = (const u8 *)ndev->dev_addr;
+
+ if (!is_valid_ether_addr(mac))
+ return -EINVAL;
+
+ for (i = 0; i < 3; i++)
+ phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
+ mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
+
+ /* Enable WOL interrupt */
+ ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
+ if (ret)
+ return ret;
+ } else {
+ /* Disable WOL interrupt */
+ ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
+ if (ret)
+ return ret;
+ }
+
+ /* Clear WOL status */
+ ret = phy_read(phydev, AT803X_INTR_STATUS);
+ if (ret < 0)
+ return ret;
+
+ /* Check if there are other interrupts except for WOL triggered when PHY is
+ * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can
+ * be passed up to the interrupt PIN.
+ */
+ irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+ if (irq_enabled < 0)
+ return irq_enabled;
+
+ irq_enabled &= ~AT803X_INTR_ENABLE_WOL;
+ if (ret & irq_enabled && !phy_polling_mode(phydev))
+ phy_trigger_machine(phydev);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_set_wol);
+
+void at803x_get_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol)
+{
+ int value;
+
+ wol->supported = WAKE_MAGIC;
+ wol->wolopts = 0;
+
+ value = phy_read(phydev, AT803X_INTR_ENABLE);
+ if (value < 0)
+ return;
+
+ if (value & AT803X_INTR_ENABLE_WOL)
+ wol->wolopts |= WAKE_MAGIC;
+}
+EXPORT_SYMBOL_GPL(at803x_get_wol);
+
+int at803x_ack_interrupt(struct phy_device *phydev)
+{
+ int err;
+
+ err = phy_read(phydev, AT803X_INTR_STATUS);
+
+ return (err < 0) ? err : 0;
+}
+EXPORT_SYMBOL_GPL(at803x_ack_interrupt);
+
+int at803x_config_intr(struct phy_device *phydev)
+{
+ int err;
+ int value;
+
+ value = phy_read(phydev, AT803X_INTR_ENABLE);
+
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+ /* Clear any pending interrupts */
+ err = at803x_ack_interrupt(phydev);
+ if (err)
+ return err;
+
+ value |= AT803X_INTR_ENABLE_AUTONEG_ERR;
+ value |= AT803X_INTR_ENABLE_SPEED_CHANGED;
+ value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
+ value |= AT803X_INTR_ENABLE_LINK_FAIL;
+ value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+
+ err = phy_write(phydev, AT803X_INTR_ENABLE, value);
+ } else {
+ err = phy_write(phydev, AT803X_INTR_ENABLE, 0);
+ if (err)
+ return err;
+
+ /* Clear any pending interrupts */
+ err = at803x_ack_interrupt(phydev);
+ }
+
+ return err;
+}
+EXPORT_SYMBOL_GPL(at803x_config_intr);
+
+irqreturn_t at803x_handle_interrupt(struct phy_device *phydev)
+{
+ int irq_status, int_enabled;
+
+ irq_status = phy_read(phydev, AT803X_INTR_STATUS);
+ if (irq_status < 0) {
+ phy_error(phydev);
+ return IRQ_NONE;
+ }
+
+ /* Read the current enabled interrupts */
+ int_enabled = phy_read(phydev, AT803X_INTR_ENABLE);
+ if (int_enabled < 0) {
+ phy_error(phydev);
+ return IRQ_NONE;
+ }
+
+ /* See if this was one of our enabled interrupts */
+ if (!(irq_status & int_enabled))
+ return IRQ_NONE;
+
+ phy_trigger_machine(phydev);
+
+ return IRQ_HANDLED;
+}
+EXPORT_SYMBOL_GPL(at803x_handle_interrupt);
+
+int at803x_read_specific_status(struct phy_device *phydev,
+ struct at803x_ss_mask ss_mask)
+{
+ int ss;
+
+ /* Read the AT8035 PHY-Specific Status register, which indicates the
+ * speed and duplex that the PHY is actually using, irrespective of
+ * whether we are in autoneg mode or not.
+ */
+ ss = phy_read(phydev, AT803X_SPECIFIC_STATUS);
+ if (ss < 0)
+ return ss;
+
+ if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) {
+ int sfc, speed;
+
+ sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL);
+ if (sfc < 0)
+ return sfc;
+
+ speed = ss & ss_mask.speed_mask;
+ speed >>= ss_mask.speed_shift;
+
+ switch (speed) {
+ case AT803X_SS_SPEED_10:
+ phydev->speed = SPEED_10;
+ break;
+ case AT803X_SS_SPEED_100:
+ phydev->speed = SPEED_100;
+ break;
+ case AT803X_SS_SPEED_1000:
+ phydev->speed = SPEED_1000;
+ break;
+ case QCA808X_SS_SPEED_2500:
+ phydev->speed = SPEED_2500;
+ break;
+ }
+ if (ss & AT803X_SS_DUPLEX)
+ phydev->duplex = DUPLEX_FULL;
+ else
+ phydev->duplex = DUPLEX_HALF;
+
+ if (ss & AT803X_SS_MDIX)
+ phydev->mdix = ETH_TP_MDI_X;
+ else
+ phydev->mdix = ETH_TP_MDI;
+
+ switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) {
+ case AT803X_SFC_MANUAL_MDI:
+ phydev->mdix_ctrl = ETH_TP_MDI;
+ break;
+ case AT803X_SFC_MANUAL_MDIX:
+ phydev->mdix_ctrl = ETH_TP_MDI_X;
+ break;
+ case AT803X_SFC_AUTOMATIC_CROSSOVER:
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+ break;
+ }
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_read_specific_status);
+
+int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+ u16 val;
+
+ switch (ctrl) {
+ case ETH_TP_MDI:
+ val = AT803X_SFC_MANUAL_MDI;
+ break;
+ case ETH_TP_MDI_X:
+ val = AT803X_SFC_MANUAL_MDIX;
+ break;
+ case ETH_TP_MDI_AUTO:
+ val = AT803X_SFC_AUTOMATIC_CROSSOVER;
+ break;
+ default:
+ return 0;
+ }
+
+ return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL,
+ AT803X_SFC_MDI_CROSSOVER_MODE_M,
+ FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val));
+}
+EXPORT_SYMBOL_GPL(at803x_config_mdix);
+
+int at803x_prepare_config_aneg(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
+ if (ret < 0)
+ return ret;
+
+ /* Changes of the midx bits are disruptive to the normal operation;
+ * therefore any changes to these registers must be followed by a
+ * software reset to take effect.
+ */
+ if (ret == 1) {
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(at803x_prepare_config_aneg);
+
+static int at803x_get_downshift(struct phy_device *phydev, u8 *d)
+{
+ int val;
+
+ val = phy_read(phydev, AT803X_SMART_SPEED);
+ if (val < 0)
+ return val;
+
+ if (val & AT803X_SMART_SPEED_ENABLE)
+ *d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2;
+ else
+ *d = DOWNSHIFT_DEV_DISABLE;
+
+ return 0;
+}
+
+static int at803x_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+ u16 mask, set;
+ int ret;
+
+ switch (cnt) {
+ case DOWNSHIFT_DEV_DEFAULT_COUNT:
+ cnt = AT803X_DEFAULT_DOWNSHIFT;
+ fallthrough;
+ case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT:
+ set = AT803X_SMART_SPEED_ENABLE |
+ AT803X_SMART_SPEED_BYPASS_TIMER |
+ FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2);
+ mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK;
+ break;
+ case DOWNSHIFT_DEV_DISABLE:
+ set = 0;
+ mask = AT803X_SMART_SPEED_ENABLE |
+ AT803X_SMART_SPEED_BYPASS_TIMER;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set);
+
+ /* After changing the smart speed settings, we need to perform a
+ * software reset, use phy_init_hw() to make sure we set the
+ * reapply any values which might got lost during software reset.
+ */
+ if (ret == 1)
+ ret = phy_init_hw(phydev);
+
+ return ret;
+}
+
+int at803x_get_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, void *data)
+{
+ switch (tuna->id) {
+ case ETHTOOL_PHY_DOWNSHIFT:
+ return at803x_get_downshift(phydev, data);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+EXPORT_SYMBOL_GPL(at803x_get_tunable);
+
+int at803x_set_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, const void *data)
+{
+ switch (tuna->id) {
+ case ETHTOOL_PHY_DOWNSHIFT:
+ return at803x_set_downshift(phydev, *(const u8 *)data);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+EXPORT_SYMBOL_GPL(at803x_set_tunable);
+
+int at803x_cdt_fault_length(int dt)
+{
+ /* According to the datasheet the distance to the fault is
+ * DELTA_TIME * 0.824 meters.
+ *
+ * The author suspect the correct formula is:
+ *
+ * fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2
+ *
+ * where c is the speed of light, VF is the velocity factor of
+ * the twisted pair cable, 125MHz the counter frequency and
+ * we need to divide by 2 because the hardware will measure the
+ * round trip time to the fault and back to the PHY.
+ *
+ * With a VF of 0.69 we get the factor 0.824 mentioned in the
+ * datasheet.
+ */
+ return (dt * 824) / 10;
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_fault_length);
+
+int at803x_cdt_start(struct phy_device *phydev, u32 cdt_start)
+{
+ return phy_write(phydev, AT803X_CDT, cdt_start);
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_start);
+
+int at803x_cdt_wait_for_completion(struct phy_device *phydev,
+ u32 cdt_en)
+{
+ int val, ret;
+
+ /* One test run takes about 25ms */
+ ret = phy_read_poll_timeout(phydev, AT803X_CDT, val,
+ !(val & cdt_en),
+ 30000, 100000, true);
+
+ return ret < 0 ? ret : 0;
+}
+EXPORT_SYMBOL_GPL(at803x_cdt_wait_for_completion);
@@ -1,5 +1,61 @@
/* SPDX-License-Identifier: GPL-2.0 */
+#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10
+#define AT803X_SFC_ASSERT_CRS BIT(11)
+#define AT803X_SFC_FORCE_LINK BIT(10)
+#define AT803X_SFC_MDI_CROSSOVER_MODE_M GENMASK(6, 5)
+#define AT803X_SFC_AUTOMATIC_CROSSOVER 0x3
+#define AT803X_SFC_MANUAL_MDIX 0x1
+#define AT803X_SFC_MANUAL_MDI 0x0
+#define AT803X_SFC_SQE_TEST BIT(2)
+#define AT803X_SFC_POLARITY_REVERSAL BIT(1)
+#define AT803X_SFC_DISABLE_JABBER BIT(0)
+
+#define AT803X_SPECIFIC_STATUS 0x11
+#define AT803X_SS_SPEED_1000 2
+#define AT803X_SS_SPEED_100 1
+#define AT803X_SS_SPEED_10 0
+#define AT803X_SS_DUPLEX BIT(13)
+#define AT803X_SS_SPEED_DUPLEX_RESOLVED BIT(11)
+#define AT803X_SS_MDIX BIT(6)
+
+#define QCA808X_SS_SPEED_2500 4
+
+#define AT803X_INTR_ENABLE 0x12
+#define AT803X_INTR_ENABLE_AUTONEG_ERR BIT(15)
+#define AT803X_INTR_ENABLE_SPEED_CHANGED BIT(14)
+#define AT803X_INTR_ENABLE_DUPLEX_CHANGED BIT(13)
+#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
+#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
+#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
+#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
+#define AT803X_INTR_ENABLE_WOL BIT(0)
+
+#define AT803X_INTR_STATUS 0x13
+
+#define AT803X_SMART_SPEED 0x14
+#define AT803X_SMART_SPEED_ENABLE BIT(5)
+#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK GENMASK(4, 2)
+#define AT803X_SMART_SPEED_BYPASS_TIMER BIT(1)
+
+#define AT803X_CDT 0x16
+#define AT803X_CDT_MDI_PAIR_MASK GENMASK(9, 8)
+#define AT803X_CDT_ENABLE_TEST BIT(0)
+#define AT803X_CDT_STATUS 0x1c
+#define AT803X_CDT_STATUS_STAT_NORMAL 0
+#define AT803X_CDT_STATUS_STAT_SHORT 1
+#define AT803X_CDT_STATUS_STAT_OPEN 2
+#define AT803X_CDT_STATUS_STAT_FAIL 3
+#define AT803X_CDT_STATUS_STAT_MASK GENMASK(9, 8)
+#define AT803X_CDT_STATUS_DELTA_TIME_MASK GENMASK(7, 0)
+
+#define AT803X_LOC_MAC_ADDR_0_15_OFFSET 0x804C
+#define AT803X_LOC_MAC_ADDR_16_31_OFFSET 0x804B
+#define AT803X_LOC_MAC_ADDR_32_47_OFFSET 0x804A
+
#define AT803X_DEBUG_ADDR 0x1D
#define AT803X_DEBUG_DATA 0x1E
@@ -16,6 +72,10 @@
#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13)
#define AT803X_DEBUG_HIB_CTRL_PS_HIB_EN BIT(15)
+#define AT803X_DEFAULT_DOWNSHIFT 5
+#define AT803X_MIN_DOWNSHIFT 2
+#define AT803X_MAX_DOWNSHIFT 9
+
enum stat_access_type {
PHY,
MMD
@@ -28,7 +88,31 @@ struct at803x_hw_stat {
enum stat_access_type access_type;
};
+struct at803x_ss_mask {
+ u16 speed_mask;
+ u8 speed_shift;
+};
+
int at803x_debug_reg_read(struct phy_device *phydev, u16 reg);
int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg,
u16 clear, u16 set);
int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data);
+int at803x_set_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol);
+void at803x_get_wol(struct phy_device *phydev,
+ struct ethtool_wolinfo *wol);
+int at803x_ack_interrupt(struct phy_device *phydev);
+int at803x_config_intr(struct phy_device *phydev);
+irqreturn_t at803x_handle_interrupt(struct phy_device *phydev);
+int at803x_read_specific_status(struct phy_device *phydev,
+ struct at803x_ss_mask ss_mask);
+int at803x_config_mdix(struct phy_device *phydev, u8 ctrl);
+int at803x_prepare_config_aneg(struct phy_device *phydev);
+int at803x_get_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, void *data);
+int at803x_set_tunable(struct phy_device *phydev,
+ struct ethtool_tunable *tuna, const void *data);
+int at803x_cdt_fault_length(int dt);
+int at803x_cdt_start(struct phy_device *phydev, u32 cdt_start);
+int at803x_cdt_wait_for_completion(struct phy_device *phydev,
+ u32 cdt_en);
Move additional functions to shared library in preparation for qca808x PHY Family to be detached from at803x driver. Only the shared defines are moved to the shared qcom.h header. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> --- drivers/net/phy/qcom/at803x.c | 428 +--------------------------- drivers/net/phy/qcom/qcom-phy-lib.c | 376 ++++++++++++++++++++++++ drivers/net/phy/qcom/qcom.h | 84 ++++++ 3 files changed, 463 insertions(+), 425 deletions(-)