| Message ID | 20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com |
|---|---|
| State | New |
| Headers | show |
| Series | [v2] wifi: wilc1000: revert reset line logic flip | expand |
Alexis Lothoré <alexis.lothore@bootlin.com> wrote: > This reverts commit fcf690b0b47494df51d214db5c5a714a400b0257. > > When using a wilc1000 chip over a spi bus, users can optionally define a > reset gpio and a chip enable gpio. The reset line of wilc1000 is active > low, so to hold the chip in reset, a low (physical) value must be applied. > > The corresponding device tree binding documentation was introduced by > commit f31ee3c0a555 ("wilc1000: Document enable-gpios and reset-gpios > properties") and correctly indicates that the reset line is an active-low > signal. The corresponding driver part, brought by commit ec031ac4792c > ("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the > correct logic. But commit fcf690b0b474 ("wifi: wilc1000: use correct > sequence of RESET for chip Power-UP/Down") eventually flipped this logic > and started misusing the gpiod APIs, applying an inverted logic when > powering up/down the chip (for example, setting the reset line to a logic > "1" during power up, which in fact asserts the reset line when device tree > describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any > platform currently using the driver in SPI mode must use a faulty reset > line description in device tree, or else chip will be maintained in reset > and will not even allow to bring up the chip. > > Fix reset line usage by inverting back the gpiod APIs usage, setting the > reset line to the logic value "0" when powering the chip, and the logic > value "1" when powering off the chip. > > Fixes: fcf690b0b474 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down") > Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> > Acked-by: Conor Dooley <conor.dooley@microchip.com> > Acked-by: Ajay Singh <ajay.kathat@microchip.com> Patch applied to wireless-next.git, thanks. f3ec64394763 wifi: wilc1000: revert reset line logic flip
diff --git a/drivers/net/wireless/microchip/wilc1000/spi.c b/drivers/net/wireless/microchip/wilc1000/spi.c index 3c4451535c8a..61c3572ce321 100644 --- a/drivers/net/wireless/microchip/wilc1000/spi.c +++ b/drivers/net/wireless/microchip/wilc1000/spi.c @@ -194,11 +194,11 @@ static void wilc_wlan_power(struct wilc *wilc, bool on) /* assert ENABLE: */ gpiod_set_value(gpios->enable, 1); mdelay(5); - /* assert RESET: */ - gpiod_set_value(gpios->reset, 1); - } else { /* deassert RESET: */ gpiod_set_value(gpios->reset, 0); + } else { + /* assert RESET: */ + gpiod_set_value(gpios->reset, 1); /* deassert ENABLE: */ gpiod_set_value(gpios->enable, 0); }
This reverts commit fcf690b0b47494df51d214db5c5a714a400b0257. When using a wilc1000 chip over a spi bus, users can optionally define a reset gpio and a chip enable gpio. The reset line of wilc1000 is active low, so to hold the chip in reset, a low (physical) value must be applied. The corresponding device tree binding documentation was introduced by commit f31ee3c0a555 ("wilc1000: Document enable-gpios and reset-gpios properties") and correctly indicates that the reset line is an active-low signal. The corresponding driver part, brought by commit ec031ac4792c ("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the correct logic. But commit fcf690b0b474 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down") eventually flipped this logic and started misusing the gpiod APIs, applying an inverted logic when powering up/down the chip (for example, setting the reset line to a logic "1" during power up, which in fact asserts the reset line when device tree describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any platform currently using the driver in SPI mode must use a faulty reset line description in device tree, or else chip will be maintained in reset and will not even allow to bring up the chip. Fix reset line usage by inverting back the gpiod APIs usage, setting the reset line to the logic value "0" when powering the chip, and the logic value "1" when powering off the chip. Fixes: fcf690b0b474 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down") Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Acked-by: Conor Dooley <conor.dooley@microchip.com> Acked-by: Ajay Singh <ajay.kathat@microchip.com> --- This issue was detected because I struggled a bit to setup a WILC-over-SPI setup, and eventually realized that it was due to chip being hold in reset. This patch may break any downstream user having a working wilc-over-spi setup (which then relies on a faulty device tree description). Discussions about this possible breakage (see v1 in link below) led to a consensus in favor of this patch. --- Changes in v2: - Link to v1: https://lore.kernel.org/r/20240213-wilc_1000_reset_line-v1-1-e01da2b23fed@bootlin.com - Fix description by mentioning the real commit at the origin of the issue - Make Fixes tag point to relevant commit - Gather Acked-By from C. Dooley and A. Singh --- drivers/net/wireless/microchip/wilc1000/spi.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) --- base-commit: 071235a89d35092c59574bf7aae3234649c97d12 change-id: 20240119-wilc_1000_reset_line-393270fc474e Best regards,