@@ -5,6 +5,7 @@
/dts-v1/;
+#include <dt-bindings/usb/pd.h>
#include "imx93.dtsi"
/ {
@@ -104,6 +105,80 @@ &mu2 {
status = "okay";
};
+&lpi2c3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <400000>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pinctrl_lpi2c3>;
+ pinctrl-1 = <&pinctrl_lpi2c3>;
+ status = "okay";
+
+ ptn5110: tcpc@50 {
+ compatible = "nxp,ptn5110";
+ reg = <0x50>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+
+ typec1_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ data-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(5000, 20000, 3000)>;
+ op-sink-microwatt = <15000000>;
+ self-powered;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ typec1_dr_sw: endpoint {
+ remote-endpoint = <&usb1_drd_sw>;
+ };
+ };
+ };
+ };
+ };
+
+ ptn5110_2: tcpc@51 {
+ compatible = "nxp,ptn5110";
+ reg = <0x51>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+
+ typec2_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ power-role = "dual";
+ data-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_VAR(5000, 20000, 3000)>;
+ op-sink-microwatt = <15000000>;
+ self-powered;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ typec2_dr_sw: endpoint {
+ remote-endpoint = <&usb2_drd_sw>;
+ };
+ };
+ };
+ };
+ };
+};
+
&eqos {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_eqos>;
@@ -156,6 +231,42 @@ &lpuart5 {
status = "okay";
};
+&usbotg1 {
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ usb-role-switch;
+ disable-over-current;
+ samsung,picophy-pre-emp-curr-control = <3>;
+ samsung,picophy-dc-vol-level-adjust = <7>;
+ status = "okay";
+
+ port {
+ usb1_drd_sw: endpoint {
+ remote-endpoint = <&typec1_dr_sw>;
+ };
+ };
+};
+
+&usbotg2 {
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ usb-role-switch;
+ disable-over-current;
+ samsung,picophy-pre-emp-curr-control = <3>;
+ samsung,picophy-dc-vol-level-adjust = <7>;
+ status = "okay";
+
+ port {
+ usb2_drd_sw: endpoint {
+ remote-endpoint = <&typec2_dr_sw>;
+ };
+ };
+};
+
&usdhc1 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc1>;
@@ -222,6 +333,13 @@ MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL 0x57e
>;
};
+ pinctrl_lpi2c3: lpi2c3grp {
+ fsl,pins = <
+ MX93_PAD_GPIO_IO28__LPI2C3_SDA 0x40000b9e
+ MX93_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e
+ >;
+ };
+
pinctrl_uart1: uart1grp {
fsl,pins = <
MX93_PAD_UART1_RXD__LPUART1_RX 0x31e
There are 2 Type-C ports and 2 USB controllers on i.MX93. Enable them. Signed-off-by: Xu Yang <xu.yang_2@nxp.com> --- Changes in v2: - remove status property in ptn5110 nodes - fix dt-schema warnings Changes in v3: - no changes Changes in v4: - no changes Changes in v5: - no changes Changes in v6: - no changes --- .../boot/dts/freescale/imx93-11x11-evk.dts | 118 ++++++++++++++++++ 1 file changed, 118 insertions(+)