diff mbox series

[v4] arm64: dts: qcom: qcm6490-idp: enable PMIC Volume and Power buttons

Message ID 20240304-gpio-keys-v4-1-03604d778c86@quicinc.com
State Superseded
Headers show
Series [v4] arm64: dts: qcom: qcm6490-idp: enable PMIC Volume and Power buttons | expand

Commit Message

Hui Liu via B4 Relay March 4, 2024, 7:09 a.m. UTC
From: Hui Liu <quic_huliu@quicinc.com>

The Volume Down & Power buttons are controlled by the PMIC via
the PON hardware, and the Volume Up is connected to a PMIC gpio.

Enable the necessary hardware and setup the GPIO state for the
Volume Up gpio key.

Signed-off-by: Hui Liu <quic_huliu@quicinc.com>
---
Changes in v4:
- Switch the order of "pinctrl-0" and "pinctrl-names".
- Update "volume_up" to "Volume_up".
- Remove "linux,input-type", because the default value is 1(EV_KEY).
- Link to v3: https://lore.kernel.org/r/20240301-gpio-keys-v3-1-ca664de8775c@quicinc.com

Changes in v3:
- Update the commit more concise and explicit.
- remove "power-source" property and update the numeric value to defined
name for "qcom,drive-strength".
- Link to v2: https://lore.kernel.org/r/20240223-gpio-keys-v2-1-19f48b3d8762@quicinc.com

Changes in v2:
- Update the commit description.
- Link to v1: https://lore.kernel.org/r/20240206-gpio-keys-v1-1-7683799daf8d@quicinc.com
---
 arch/arm64/boot/dts/qcom/qcm6490-idp.dts | 41 ++++++++++++++++++++++++++++++++
 1 file changed, 41 insertions(+)


---
base-commit: 23e11d0318521e8693459b0e4d23aec614b3b68b
change-id: 20240206-gpio-keys-138bbd850298

Best regards,

Comments

hui liu March 11, 2024, 10:03 a.m. UTC | #1
On 3/6/2024 3:56 PM, Dmitry Baryshkov wrote:
> On Wed, 6 Mar 2024 at 05:02, hui liu <quic_huliu@quicinc.com> wrote:
>>
>>
>>
>> On 3/6/2024 5:20 AM, Konrad Dybcio wrote:
>>>
>>>
>>> On 3/4/24 08:09, Hui Liu via B4 Relay wrote:
>>>> From: Hui Liu <quic_huliu@quicinc.com>
>>>>
>>>> The Volume Down & Power buttons are controlled by the PMIC via
>>>> the PON hardware, and the Volume Up is connected to a PMIC gpio.
>>>>
>>>> Enable the necessary hardware and setup the GPIO state for the
>>>> Volume Up gpio key.
>>>>
>>>> Signed-off-by: Hui Liu <quic_huliu@quicinc.com>
>>>> ---
>>>
>>> [...]
>>>
>>>
>>>> +&pmk8350_pon {
>>>> +    status = "okay";
>>>> +};
>>>
>>> This device is already enabled
>> Hi Konrad,
>>
>> The status is not set in pmk8350.dtsi, so I thought we should set it for
>> "okay" manually. Do you think so?
> 
> What is the default device status if there is no status property?
The default status is okay.
OK, I will update it, remove the status configuration.

Thanks,
Hui
> 
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
index acf145d1d97c..12e162613ed0 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
@@ -9,7 +9,9 @@ 
 #define PM7250B_SID 8
 #define PM7250B_SID1 9
 
+#include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sc7280.dtsi"
 #include "pm7250b.dtsi"
@@ -39,6 +41,22 @@  chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&key_vol_up_default>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume_up";
+			gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+	};
+
 	reserved-memory {
 		xbl_mem: xbl@80700000 {
 			reg = <0x0 0x80700000 0x0 0x100000>;
@@ -421,6 +439,16 @@  vreg_bob_3p296: bob {
 	};
 };
 
+&pm7325_gpios {
+	key_vol_up_default: key-vol-up-state {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
 &pm8350c_pwm {
 	status = "okay";
 
@@ -448,6 +476,19 @@  led@3 {
 	};
 };
 
+&pmk8350_pon {
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };