diff mbox series

[08/10] arm64: dts: qcom: sc8180x: Add USB MP controller and phys

Message ID 20240525-sc8180x-usb-mp-v1-8-60a904392438@quicinc.com
State New
Headers show
Series arm64: dts: qcom: sc8180x: Enable the USB multiport controller | expand

Commit Message

Bjorn Andersson May 25, 2024, 6:04 p.m. UTC
From: Bjorn Andersson <quic_bjorande@quicinc.com>

The SC8180X platform comes with a multiport DWC3 controller with two
ports, each connected to a pair of HighSpeed and QMP SuperSpeed PHYs.

Describe these blocks.

Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
---
 arch/arm64/boot/dts/qcom/sc8180x.dtsi | 146 ++++++++++++++++++++++++++++++++++
 1 file changed, 146 insertions(+)

Comments

Dmitry Baryshkov May 25, 2024, 8:16 p.m. UTC | #1
On Sat, May 25, 2024 at 11:04:01AM -0700, Bjorn Andersson wrote:
> From: Bjorn Andersson <quic_bjorande@quicinc.com>
> 
> The SC8180X platform comes with a multiport DWC3 controller with two
> ports, each connected to a pair of HighSpeed and QMP SuperSpeed PHYs.
> 
> Describe these blocks.
> 
> Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/sc8180x.dtsi | 146 ++++++++++++++++++++++++++++++++++
>  1 file changed, 146 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Konrad Dybcio May 28, 2024, 12:53 p.m. UTC | #2
On 5/25/24 20:04, Bjorn Andersson wrote:
> From: Bjorn Andersson <quic_bjorande@quicinc.com>
> 
> The SC8180X platform comes with a multiport DWC3 controller with two
> ports, each connected to a pair of HighSpeed and QMP SuperSpeed PHYs.
> 
> Describe these blocks.
> 
> Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
> ---
>   arch/arm64/boot/dts/qcom/sc8180x.dtsi | 146 ++++++++++++++++++++++++++++++++++
>   1 file changed, 146 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
> index 9ef3fa40e1d8..0950dc7adb20 100644
> --- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
> @@ -2511,6 +2511,34 @@ usb_sec_hsphy: phy@88e3000 {
>   			status = "disabled";
>   		};
>   
> +		usb_mp0_hsphy: phy@88e4000 {

Even though the register names are MPn, I think this is a bit confusing..

There's only one MP controller, so perhaps usb_mp_hsphy0?

[...]

> +			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
> +				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> +				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
> +				 <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>;

PIPE_1_CLK

> +			clock-names = "aux", "ref", "com_aux", "pipe";

This could be a vertical list

> +
> +			resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>,
> +				 <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>;
> +			reset-names = "phy", "phy_phy";
> +
> +			power-domains = <&gcc USB30_MP_GDSC>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "usb2_phy1_pipe_clk";
> +
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
>   		usb_sec_qmpphy: phy@88ee000 {
>   			compatible = "qcom,sc8180x-qmp-usb3-dp-phy";
>   			reg = <0 0x088ee000 0 0x18c>,
> @@ -2662,6 +2738,76 @@ gem_noc: interconnect@9680000 {
>   			qcom,bcm-voters = <&apps_bcm_voter>;
>   		};
>   
> +		usb_mp: usb@a4f8800 {
> +			compatible = "qcom,sc8180x-dwc3-mp", "qcom,dwc3";
> +			reg = <0 0x0a4f8800 0 0x400>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +			dma-ranges;
> +
> +			clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
> +				 <&gcc GCC_USB30_MP_MASTER_CLK>,
> +				 <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
> +				 <&gcc GCC_USB30_MP_SLEEP_CLK>,
> +				 <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
> +				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;

This is used by the secondary DWC3 (non-MP). Are you sure?

Actually, are we sure that these clocks are really supplying the DWC3s?

> +			clock-names = "cfg_noc",
> +				      "core",
> +				      "iface",
> +				      "sleep",
> +				      "mock_utmi",
> +				      "xo";
> +
> +			interconnects = <&aggre1_noc MASTER_USB3_2 0 &mc_virt SLAVE_EBI_CH0 0>,
> +					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3_2 0>;
> +			interconnect-names = "usb-ddr", "apps-usb";
> +
> +			assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
> +					  <&gcc GCC_USB30_MP_MASTER_CLK>;
> +			assigned-clock-rates = <19200000>, <200000000>;
> +
> +			interrupts-extended = <&intc GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&intc GIC_SPI 655 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&intc GIC_SPI 658 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&intc GIC_SPI 657 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&pdc 59 IRQ_TYPE_EDGE_BOTH>,
> +					      <&pdc 46 IRQ_TYPE_EDGE_BOTH>,
> +					      <&pdc 71 IRQ_TYPE_EDGE_BOTH>,
> +					      <&pdc 68 IRQ_TYPE_EDGE_BOTH>,
> +					      <&pdc 7 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&pdc 30 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "pwr_event_1", "pwr_event_2",
> +					  "hs_phy_1",	 "hs_phy_2",
> +					  "dp_hs_phy_1", "dm_hs_phy_1",
> +					  "dp_hs_phy_2", "dm_hs_phy_2",
> +					  "ss_phy_1",	 "ss_phy_2";
> +
> +			power-domains = <&gcc USB30_MP_GDSC>;
> +
> +			resets = <&gcc GCC_USB30_MP_BCR>;
> +
> +			status = "disabled";
> +
> +			usb_mp_dwc3: usb@a400000 {
> +				compatible = "snps,dwc3";
> +				reg = <0 0x0a400000 0 0xcd00>;
> +				interrupts = <GIC_SPI 654 IRQ_TYPE_LEVEL_HIGH>;
> +				iommus = <&apps_smmu 0x60 0>;
> +				snps,dis_u2_susphy_quirk;
> +				snps,dis_enblslpm_quirk;

sa8195-usb.dtsi lists a bunch more fluff:

snps,has-lpm-erratum;
snps,hird-threshold = /bits/ 8 <0x0>;
snps,is-utmi-l1-suspend;
snps,ssp-u3-u0-quirk;
snps,dis-u1-entry-quirk;
snps,dis-u2-entry-quirk;
snps,dis_u3_susphy_quirk;
snps,force-gen1;
maximum-speed = "super-speed";

the irq numbers look good

Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sc8180x.dtsi b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
index 9ef3fa40e1d8..0950dc7adb20 100644
--- a/arch/arm64/boot/dts/qcom/sc8180x.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc8180x.dtsi
@@ -2511,6 +2511,34 @@  usb_sec_hsphy: phy@88e3000 {
 			status = "disabled";
 		};
 
+		usb_mp0_hsphy: phy@88e4000 {
+			compatible = "qcom,sc8180x-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0 0x088e4000 0 0x400>;
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_MP0_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_mp1_hsphy: phy@88e5000 {
+			compatible = "qcom,sc8180x-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0 0x088e5000 0 0x400>;
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_MP1_BCR>;
+
+			status = "disabled";
+		};
+
 		usb_prim_qmpphy: phy@88e9000 {
 			compatible = "qcom,sc8180x-qmp-usb3-dp-phy";
 			reg = <0 0x088e9000 0 0x18c>,
@@ -2577,6 +2605,54 @@  usb_prim_dpphy: dp-phy@88ea200 {
 			};
 		};
 
+		usb_mp0_qmpphy: phy@88eb000 {
+			compatible = "qcom,sc8180x-qmp-usb3-uni-phy";
+			reg = <0 0x088eb000 0 0x1000>;
+
+			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>;
+			clock-names = "aux", "ref", "com_aux", "pipe";
+
+			resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>,
+				 <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>;
+			reset-names = "phy", "phy_phy";
+
+			power-domains = <&gcc USB30_MP_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "usb2_phy0_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_mp1_qmpphy: phy@88ec000 {
+			compatible = "qcom,sc8180x-qmp-usb3-uni-phy";
+			reg = <0 0x088ec000 0 0x1000>;
+
+			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>;
+			clock-names = "aux", "ref", "com_aux", "pipe";
+
+			resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>,
+				 <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>;
+			reset-names = "phy", "phy_phy";
+
+			power-domains = <&gcc USB30_MP_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "usb2_phy1_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		usb_sec_qmpphy: phy@88ee000 {
 			compatible = "qcom,sc8180x-qmp-usb3-dp-phy";
 			reg = <0 0x088ee000 0 0x18c>,
@@ -2662,6 +2738,76 @@  gem_noc: interconnect@9680000 {
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		usb_mp: usb@a4f8800 {
+			compatible = "qcom,sc8180x-dwc3-mp", "qcom,dwc3";
+			reg = <0 0x0a4f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			dma-ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
+				 <&gcc GCC_USB30_MP_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
+				 <&gcc GCC_USB30_MP_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
+
+			interconnects = <&aggre1_noc MASTER_USB3_2 0 &mc_virt SLAVE_EBI_CH0 0>,
+					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3_2 0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
+			assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MP_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 655 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 658 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 657 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 59 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 46 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 71 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 68 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 7 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event_1", "pwr_event_2",
+					  "hs_phy_1",	 "hs_phy_2",
+					  "dp_hs_phy_1", "dm_hs_phy_1",
+					  "dp_hs_phy_2", "dm_hs_phy_2",
+					  "ss_phy_1",	 "ss_phy_2";
+
+			power-domains = <&gcc USB30_MP_GDSC>;
+
+			resets = <&gcc GCC_USB30_MP_BCR>;
+
+			status = "disabled";
+
+			usb_mp_dwc3: usb@a400000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a400000 0 0xcd00>;
+				interrupts = <GIC_SPI 654 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x60 0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_mp0_hsphy>,
+				       <&usb_mp0_qmpphy>,
+				       <&usb_mp1_hsphy>,
+				       <&usb_mp1_qmpphy>;
+				phy-names = "usb2-0",
+					    "usb3-0",
+					    "usb2-1",
+					    "usb3-1";
+				dr_mode = "host";
+			};
+		};
+
 		usb_prim: usb@a6f8800 {
 			compatible = "qcom,sc8180x-dwc3", "qcom,dwc3";
 			reg = <0 0x0a6f8800 0 0x400>;