| Message ID | 20240613-aspeed-udc-v2-1-29501ce9cb7a@codeconstruct.com.au |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v2] usb: gadget: aspeed_udc: fix device address configuration | expand |
diff --git a/drivers/usb/gadget/udc/aspeed_udc.c b/drivers/usb/gadget/udc/aspeed_udc.c index 3916c8e2ba01..821a6ab5da56 100644 --- a/drivers/usb/gadget/udc/aspeed_udc.c +++ b/drivers/usb/gadget/udc/aspeed_udc.c @@ -66,8 +66,8 @@ #define USB_UPSTREAM_EN BIT(0) /* Main config reg */ -#define UDC_CFG_SET_ADDR(x) ((x) & 0x3f) -#define UDC_CFG_ADDR_MASK (0x3f) +#define UDC_CFG_SET_ADDR(x) ((x) & UDC_CFG_ADDR_MASK) +#define UDC_CFG_ADDR_MASK GENMASK(6, 0) /* Interrupt ctrl & status reg */ #define UDC_IRQ_EP_POOL_NAK BIT(17)
In the aspeed UDC setup, we configure the UDC hardware with the assigned USB device address. However, we have an off-by-one in the bitmask, so we're only setting the lower 6 bits of the address (USB addresses being 7 bits, and the hardware bitmask being bits 0:6). This means that device enumeration fails if the assigned address is greater than 64: [ 344.607255] usb 1-1: new high-speed USB device number 63 using ehci-platform [ 344.808459] usb 1-1: New USB device found, idVendor=cc00, idProduct=cc00, bcdDevice= 6.10 [ 344.817684] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 344.825671] usb 1-1: Product: Test device [ 344.831075] usb 1-1: Manufacturer: Test vendor [ 344.836335] usb 1-1: SerialNumber: 00 [ 349.917181] usb 1-1: USB disconnect, device number 63 [ 352.036775] usb 1-1: new high-speed USB device number 64 using ehci-platform [ 352.249432] usb 1-1: device descriptor read/all, error -71 [ 352.696740] usb 1-1: new high-speed USB device number 65 using ehci-platform [ 352.909431] usb 1-1: device descriptor read/all, error -71 Use the correct mask of 0x7f (rather than 0x3f), and generate this through the GENMASK macro, so we have numbers that correspond exactly to the hardware register definition. Fixes: 055276c13205 ("usb: gadget: add Aspeed ast2600 udc driver") Cc: stable@vger.kernel.org Reviewed-by: Neal Liu <neal_liu@aspeedtech.com> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> --- v2: - Add Cc: stable@ tag - v1: https://lore.kernel.org/r/20240612-aspeed-udc-v1-1-d277b553aecf@codeconstruct.com.au --- drivers/usb/gadget/udc/aspeed_udc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) --- base-commit: 32f88d65f01bf6f45476d7edbe675e44fb9e1d58 change-id: 20240611-aspeed-udc-07dcde062ccf Best regards,