| Message ID | 20240620104444.5862-22-victorshihgli@gmail.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add support UHS-II for GL9755 and GL9767 | expand |
Hi Victor, On Thu, Jun 20, 2024 at 6:46 PM Victor Shih <victorshihgli@gmail.com> wrote: > > From: Victor Shih <victor.shih@genesyslogic.com.tw> > > Changes are: > * Disable GL9755 overcurrent interrupt when power on/off on UHS-II. > * Enable the internal clock when do reset on UHS-II mode. > * Increase timeout value before detecting UHS-II interface. > * Add vendor settings fro UHS-II mode. > > Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> > Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> > Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw> > --- > > Updates in V17: > - Rname gl9755_overcurrent_event_enable() to > sdhci_gli_overcurrent_event_enable(). > > Updates in V15: > - Adjust gl9755_vendor_init() to the correct function. > > Updates in V13: > - Ues uhs2_sd_tran to stead MMC_UHS2_SD_TRAN. > > Updates in V9: > - Rename gl9755_pre_detect_init() to sdhci_gli_pre_detect_init(). > - Rename gl9755_uhs2_reset_sd_tran() to sdhci_gli_uhs2_reset_sd_tran(). > > Updates in V8: > - Use sdhci_get_vdd_value() to simplify code in gl9755_set_power(). > - Use read_poll_timeout_atomic() to simplify code in > sdhci_wait_clock_stable(). > - Use read_poll_timeout_atomic() to simplify code in sdhci_gl9755_reset(). > > Updates in V7: > - Drop using gl9755_post_attach_sd(). > > --- > > drivers/mmc/host/sdhci-pci-gli.c | 232 ++++++++++++++++++++++++++++++- > 1 file changed, 231 insertions(+), 1 deletion(-) > > diff --git a/drivers/mmc/host/sdhci-pci-gli.c b/drivers/mmc/host/sdhci-pci-gli.c > index 0f81586a19df..a4164948de81 100644 > --- a/drivers/mmc/host/sdhci-pci-gli.c > +++ b/drivers/mmc/host/sdhci-pci-gli.c > @@ -18,6 +18,7 @@ > #include "sdhci-cqhci.h" > #include "sdhci-pci.h" > #include "cqhci.h" > +#include "sdhci-uhs2.h" > > /* Genesys Logic extra registers */ > #define SDHCI_GLI_9750_WT 0x800 > @@ -139,9 +140,36 @@ > > #define PCI_GLI_9755_PLLSSC 0x68 > #define PCI_GLI_9755_PLLSSC_PPM GENMASK(15, 0) > +#define PCI_GLI_9755_PLLSSC_RTL BIT(24) > +#define GLI_9755_PLLSSC_RTL_VALUE 0x1 > +#define PCI_GLI_9755_PLLSSC_TRANS_PASS BIT(27) > +#define GLI_9755_PLLSSC_TRANS_PASS_VALUE 0x1 > +#define PCI_GLI_9755_PLLSSC_RECV GENMASK(29, 28) > +#define GLI_9755_PLLSSC_RECV_VALUE 0x0 > +#define PCI_GLI_9755_PLLSSC_TRAN GENMASK(31, 30) > +#define GLI_9755_PLLSSC_TRAN_VALUE 0x3 > + > +#define PCI_GLI_9755_UHS2_PLL 0x6C > +#define PCI_GLI_9755_UHS2_PLL_SSC GENMASK(9, 8) > +#define GLI_9755_UHS2_PLL_SSC_VALUE 0x0 > +#define PCI_GLI_9755_UHS2_PLL_DELAY BIT(18) > +#define GLI_9755_UHS2_PLL_DELAY_VALUE 0x1 > +#define PCI_GLI_9755_UHS2_PLL_PDRST BIT(27) > +#define GLI_9755_UHS2_PLL_PDRST_VALUE 0x1 > > #define PCI_GLI_9755_SerDes 0x70 > +#define PCI_GLI_9755_UHS2_SERDES_INTR GENMASK(2, 0) > +#define GLI_9755_UHS2_SERDES_INTR_VALUE 0x3 > +#define PCI_GLI_9755_UHS2_SERDES_ZC1 BIT(3) > +#define GLI_9755_UHS2_SERDES_ZC1_VALUE 0x0 > +#define PCI_GLI_9755_UHS2_SERDES_ZC2 GENMASK(7, 4) > +#define GLI_9755_UHS2_SERDES_ZC2_DEFAULT 0xB > +#define GLI_9755_UHS2_SERDES_ZC2_SANDISK 0x0 > #define PCI_GLI_9755_SCP_DIS BIT(19) > +#define PCI_GLI_9755_UHS2_SERDES_TRAN GENMASK(27, 24) > +#define GLI_9755_UHS2_SERDES_TRAN_VALUE 0xC > +#define PCI_GLI_9755_UHS2_SERDES_RECV GENMASK(31, 28) > +#define GLI_9755_UHS2_SERDES_RECV_VALUE 0xF > > #define PCI_GLI_9755_MISC 0x78 > #define PCI_GLI_9755_MISC_SSC_OFF BIT(26) > @@ -779,6 +807,200 @@ static void gl9755_hw_setting(struct sdhci_pci_slot *slot) > gl9755_wt_off(pdev); > } > > +static void gl9755_vendor_init(struct sdhci_host *host) > +{ > + struct sdhci_pci_slot *slot = sdhci_priv(host); > + struct pci_dev *pdev = slot->chip->pdev; > + u32 serdes; > + u32 pllssc; > + u32 uhs2_pll; > + > + gl9755_wt_on(pdev); > + > + pci_read_config_dword(pdev, PCI_GLI_9755_SerDes, &serdes); > + serdes &= ~PCI_GLI_9755_UHS2_SERDES_TRAN; > + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_TRAN, > + GLI_9755_UHS2_SERDES_TRAN_VALUE); > + serdes &= ~PCI_GLI_9755_UHS2_SERDES_RECV; > + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_RECV, > + GLI_9755_UHS2_SERDES_RECV_VALUE); > + serdes &= ~PCI_GLI_9755_UHS2_SERDES_INTR; > + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_INTR, > + GLI_9755_UHS2_SERDES_INTR_VALUE); > + serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC1; > + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC1, > + GLI_9755_UHS2_SERDES_ZC1_VALUE); > + serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC2; > + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC2, > + GLI_9755_UHS2_SERDES_ZC2_DEFAULT); > + pci_write_config_dword(pdev, PCI_GLI_9755_SerDes, serdes); > + > + pci_read_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, &uhs2_pll); > + uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_SSC; > + uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_SSC, > + GLI_9755_UHS2_PLL_SSC_VALUE); > + uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_DELAY; > + uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_DELAY, > + GLI_9755_UHS2_PLL_DELAY_VALUE); > + uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_PDRST; > + uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_PDRST, > + GLI_9755_UHS2_PLL_PDRST_VALUE); > + pci_write_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, uhs2_pll); > + > + pci_read_config_dword(pdev, PCI_GLI_9755_PLLSSC, &pllssc); > + pllssc &= ~PCI_GLI_9755_PLLSSC_RTL; > + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RTL, > + GLI_9755_PLLSSC_RTL_VALUE); > + pllssc &= ~PCI_GLI_9755_PLLSSC_TRANS_PASS; > + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRANS_PASS, > + GLI_9755_PLLSSC_TRANS_PASS_VALUE); > + pllssc &= ~PCI_GLI_9755_PLLSSC_RECV; > + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RECV, > + GLI_9755_PLLSSC_RECV_VALUE); > + pllssc &= ~PCI_GLI_9755_PLLSSC_TRAN; > + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRAN, > + GLI_9755_PLLSSC_TRAN_VALUE); > + pci_write_config_dword(pdev, PCI_GLI_9755_PLLSSC, pllssc); > + > + gl9755_wt_off(pdev); > +} > + > +static void sdhci_gli_pre_detect_init(struct sdhci_host *host) > +{ > + /* Need more time on UHS2 detect flow */ > + sdhci_writeb(host, 0xA7, SDHCI_UHS2_TIMER_CTRL); > +} > + > +static void sdhci_gli_overcurrent_event_enable(struct sdhci_host *host, bool enable) > +{ > + u32 mask; > + > + mask = sdhci_readl(host, SDHCI_SIGNAL_ENABLE); > + if (enable) > + mask |= SDHCI_INT_BUS_POWER; > + else > + mask &= ~SDHCI_INT_BUS_POWER; > + > + sdhci_writel(host, mask, SDHCI_SIGNAL_ENABLE); > + > + mask = sdhci_readl(host, SDHCI_INT_ENABLE); > + if (enable) > + mask |= SDHCI_INT_BUS_POWER; > + else > + mask &= ~SDHCI_INT_BUS_POWER; > + > + sdhci_writel(host, mask, SDHCI_INT_ENABLE); > +} > + > +static void gl9755_set_power(struct sdhci_host *host, unsigned char mode, > + unsigned short vdd) > +{ > + u8 pwr = 0; > + > + if (mode != MMC_POWER_OFF) { > + pwr = sdhci_get_vdd_value(vdd); > + if (!pwr) > + WARN(1, "%s: Invalid vdd %#x\n", mmc_hostname(host->mmc), vdd); > + pwr |= SDHCI_VDD2_POWER_180; > + } > + > + if (host->pwr == pwr) > + return; > + > + host->pwr = pwr; > + > + if (pwr == 0) { > + sdhci_gli_overcurrent_event_enable(host, false); > + sdhci_writeb(host, 0, SDHCI_POWER_CONTROL); > + } else { > + sdhci_gli_overcurrent_event_enable(host, false); > + sdhci_writeb(host, 0, SDHCI_POWER_CONTROL); > + > + pwr |= (SDHCI_POWER_ON | SDHCI_VDD2_POWER_ON); > + > + sdhci_writeb(host, pwr & 0xf, SDHCI_POWER_CONTROL); > + /* wait stable */ > + mdelay(5); > + sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL); > + /* wait stable */ > + mdelay(5); > + sdhci_gli_overcurrent_event_enable(host, true); > + } > +} > + > +static bool sdhci_wait_clock_stable(struct sdhci_host *host) > +{ > + u16 clk = 0; > + > + if (read_poll_timeout_atomic(sdhci_readw, clk, (clk & SDHCI_CLOCK_INT_STABLE), > + 10, 20000, false, host, SDHCI_CLOCK_CONTROL)) { > + pr_err("%s: Internal clock never stabilised.\n", mmc_hostname(host->mmc)); > + sdhci_dumpregs(host); > + return false; > + } > + return true; > +} > + > +static void sdhci_gli_uhs2_reset_sd_tran(struct sdhci_host *host) > +{ > + /* do this on UHS2 mode */ > + if (host->mmc->uhs2_sd_tran) { > + sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_SD); > + sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); > + sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); > + sdhci_uhs2_clear_set_irqs(host, > + SDHCI_INT_ALL_MASK, > + SDHCI_UHS2_INT_ERROR_MASK); > + } > +} > + > +static void sdhci_gl9755_reset(struct sdhci_host *host, u8 mask) > +{ > + u16 clk_ctrl; > + u16 ctrl2; > + u8 rst; > + > + /* need internal clock */ > + if (mask & SDHCI_RESET_ALL) { > + ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); > + clk_ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL); > + > + if ((ctrl2 & SDHCI_CTRL_V4_MODE) && > + (ctrl2 & SDHCI_CTRL_UHS2_ENABLE)) { > + sdhci_writew(host, > + SDHCI_CLOCK_INT_EN, > + SDHCI_CLOCK_CONTROL); > + } else { > + sdhci_writew(host, > + SDHCI_CLOCK_INT_EN, > + SDHCI_CLOCK_CONTROL); > + sdhci_wait_clock_stable(host); > + sdhci_writew(host, > + SDHCI_CTRL_V4_MODE, > + SDHCI_HOST_CONTROL2); > + } > + } > + > + sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET); > + > + /* reset sd-tran on UHS2 mode if need to reset cmd/data */ > + if ((mask & SDHCI_RESET_CMD) | (mask & SDHCI_RESET_DATA)) This may be -> if ((mask & SDHCI_RESET_CMD) || (mask & SDHCI_RESET_DATA)) Best regards, Ben Chuang > + sdhci_gli_uhs2_reset_sd_tran(host); > + > + if (mask & SDHCI_RESET_ALL) > + host->clock = 0; > + > + /* hw clears the bit when it's done */ > + if (read_poll_timeout_atomic(sdhci_readb, rst, !(rst & mask), > + 10, 100000, false, host, SDHCI_SOFTWARE_RESET)) { > + pr_err("%s: Reset 0x%x never completed.\n", mmc_hostname(host->mmc), (int)mask); > + sdhci_dumpregs(host); > + /* manual clear */ > + sdhci_writeb(host, 0, SDHCI_SOFTWARE_RESET); > + return; > + } > +} > + > static inline void gl9767_vhs_read(struct pci_dev *pdev) > { > u32 vhs_enable; > @@ -1086,6 +1308,7 @@ static int gli_probe_slot_gl9755(struct sdhci_pci_slot *slot) > gli_pcie_enable_msi(slot); > slot->host->mmc->caps2 |= MMC_CAP2_NO_SDIO; > sdhci_enable_v4_mode(host); > + gl9755_vendor_init(host); > > return 0; > } > @@ -1524,17 +1747,24 @@ static const struct sdhci_ops sdhci_gl9755_ops = { > .read_w = sdhci_gli_readw, > .read_b = sdhci_gli_readb, > .set_clock = sdhci_gl9755_set_clock, > + .set_power = gl9755_set_power, > .enable_dma = sdhci_pci_enable_dma, > .set_bus_width = sdhci_set_bus_width, > - .reset = sdhci_reset, > + .reset = sdhci_gl9755_reset, > .set_uhs_signaling = sdhci_set_uhs_signaling, > .voltage_switch = sdhci_gli_voltage_switch, > + .dump_uhs2_regs = sdhci_uhs2_dump_regs, > + .set_timeout = sdhci_uhs2_set_timeout, > + .irq = sdhci_uhs2_irq, > + .uhs2_pre_detect_init = sdhci_gli_pre_detect_init, > }; > > const struct sdhci_pci_fixes sdhci_gl9755 = { > .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC, > .quirks2 = SDHCI_QUIRK2_BROKEN_DDR50, > .probe_slot = gli_probe_slot_gl9755, > + .add_host = sdhci_pci_uhs2_add_host, > + .remove_host = sdhci_pci_uhs2_remove_host, > .ops = &sdhci_gl9755_ops, > #ifdef CONFIG_PM_SLEEP > .resume = sdhci_pci_gli_resume, > -- > 2.25.1 >
diff --git a/drivers/mmc/host/sdhci-pci-gli.c b/drivers/mmc/host/sdhci-pci-gli.c index 0f81586a19df..a4164948de81 100644 --- a/drivers/mmc/host/sdhci-pci-gli.c +++ b/drivers/mmc/host/sdhci-pci-gli.c @@ -18,6 +18,7 @@ #include "sdhci-cqhci.h" #include "sdhci-pci.h" #include "cqhci.h" +#include "sdhci-uhs2.h" /* Genesys Logic extra registers */ #define SDHCI_GLI_9750_WT 0x800 @@ -139,9 +140,36 @@ #define PCI_GLI_9755_PLLSSC 0x68 #define PCI_GLI_9755_PLLSSC_PPM GENMASK(15, 0) +#define PCI_GLI_9755_PLLSSC_RTL BIT(24) +#define GLI_9755_PLLSSC_RTL_VALUE 0x1 +#define PCI_GLI_9755_PLLSSC_TRANS_PASS BIT(27) +#define GLI_9755_PLLSSC_TRANS_PASS_VALUE 0x1 +#define PCI_GLI_9755_PLLSSC_RECV GENMASK(29, 28) +#define GLI_9755_PLLSSC_RECV_VALUE 0x0 +#define PCI_GLI_9755_PLLSSC_TRAN GENMASK(31, 30) +#define GLI_9755_PLLSSC_TRAN_VALUE 0x3 + +#define PCI_GLI_9755_UHS2_PLL 0x6C +#define PCI_GLI_9755_UHS2_PLL_SSC GENMASK(9, 8) +#define GLI_9755_UHS2_PLL_SSC_VALUE 0x0 +#define PCI_GLI_9755_UHS2_PLL_DELAY BIT(18) +#define GLI_9755_UHS2_PLL_DELAY_VALUE 0x1 +#define PCI_GLI_9755_UHS2_PLL_PDRST BIT(27) +#define GLI_9755_UHS2_PLL_PDRST_VALUE 0x1 #define PCI_GLI_9755_SerDes 0x70 +#define PCI_GLI_9755_UHS2_SERDES_INTR GENMASK(2, 0) +#define GLI_9755_UHS2_SERDES_INTR_VALUE 0x3 +#define PCI_GLI_9755_UHS2_SERDES_ZC1 BIT(3) +#define GLI_9755_UHS2_SERDES_ZC1_VALUE 0x0 +#define PCI_GLI_9755_UHS2_SERDES_ZC2 GENMASK(7, 4) +#define GLI_9755_UHS2_SERDES_ZC2_DEFAULT 0xB +#define GLI_9755_UHS2_SERDES_ZC2_SANDISK 0x0 #define PCI_GLI_9755_SCP_DIS BIT(19) +#define PCI_GLI_9755_UHS2_SERDES_TRAN GENMASK(27, 24) +#define GLI_9755_UHS2_SERDES_TRAN_VALUE 0xC +#define PCI_GLI_9755_UHS2_SERDES_RECV GENMASK(31, 28) +#define GLI_9755_UHS2_SERDES_RECV_VALUE 0xF #define PCI_GLI_9755_MISC 0x78 #define PCI_GLI_9755_MISC_SSC_OFF BIT(26) @@ -779,6 +807,200 @@ static void gl9755_hw_setting(struct sdhci_pci_slot *slot) gl9755_wt_off(pdev); } +static void gl9755_vendor_init(struct sdhci_host *host) +{ + struct sdhci_pci_slot *slot = sdhci_priv(host); + struct pci_dev *pdev = slot->chip->pdev; + u32 serdes; + u32 pllssc; + u32 uhs2_pll; + + gl9755_wt_on(pdev); + + pci_read_config_dword(pdev, PCI_GLI_9755_SerDes, &serdes); + serdes &= ~PCI_GLI_9755_UHS2_SERDES_TRAN; + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_TRAN, + GLI_9755_UHS2_SERDES_TRAN_VALUE); + serdes &= ~PCI_GLI_9755_UHS2_SERDES_RECV; + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_RECV, + GLI_9755_UHS2_SERDES_RECV_VALUE); + serdes &= ~PCI_GLI_9755_UHS2_SERDES_INTR; + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_INTR, + GLI_9755_UHS2_SERDES_INTR_VALUE); + serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC1; + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC1, + GLI_9755_UHS2_SERDES_ZC1_VALUE); + serdes &= ~PCI_GLI_9755_UHS2_SERDES_ZC2; + serdes |= FIELD_PREP(PCI_GLI_9755_UHS2_SERDES_ZC2, + GLI_9755_UHS2_SERDES_ZC2_DEFAULT); + pci_write_config_dword(pdev, PCI_GLI_9755_SerDes, serdes); + + pci_read_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, &uhs2_pll); + uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_SSC; + uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_SSC, + GLI_9755_UHS2_PLL_SSC_VALUE); + uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_DELAY; + uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_DELAY, + GLI_9755_UHS2_PLL_DELAY_VALUE); + uhs2_pll &= ~PCI_GLI_9755_UHS2_PLL_PDRST; + uhs2_pll |= FIELD_PREP(PCI_GLI_9755_UHS2_PLL_PDRST, + GLI_9755_UHS2_PLL_PDRST_VALUE); + pci_write_config_dword(pdev, PCI_GLI_9755_UHS2_PLL, uhs2_pll); + + pci_read_config_dword(pdev, PCI_GLI_9755_PLLSSC, &pllssc); + pllssc &= ~PCI_GLI_9755_PLLSSC_RTL; + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RTL, + GLI_9755_PLLSSC_RTL_VALUE); + pllssc &= ~PCI_GLI_9755_PLLSSC_TRANS_PASS; + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRANS_PASS, + GLI_9755_PLLSSC_TRANS_PASS_VALUE); + pllssc &= ~PCI_GLI_9755_PLLSSC_RECV; + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_RECV, + GLI_9755_PLLSSC_RECV_VALUE); + pllssc &= ~PCI_GLI_9755_PLLSSC_TRAN; + pllssc |= FIELD_PREP(PCI_GLI_9755_PLLSSC_TRAN, + GLI_9755_PLLSSC_TRAN_VALUE); + pci_write_config_dword(pdev, PCI_GLI_9755_PLLSSC, pllssc); + + gl9755_wt_off(pdev); +} + +static void sdhci_gli_pre_detect_init(struct sdhci_host *host) +{ + /* Need more time on UHS2 detect flow */ + sdhci_writeb(host, 0xA7, SDHCI_UHS2_TIMER_CTRL); +} + +static void sdhci_gli_overcurrent_event_enable(struct sdhci_host *host, bool enable) +{ + u32 mask; + + mask = sdhci_readl(host, SDHCI_SIGNAL_ENABLE); + if (enable) + mask |= SDHCI_INT_BUS_POWER; + else + mask &= ~SDHCI_INT_BUS_POWER; + + sdhci_writel(host, mask, SDHCI_SIGNAL_ENABLE); + + mask = sdhci_readl(host, SDHCI_INT_ENABLE); + if (enable) + mask |= SDHCI_INT_BUS_POWER; + else + mask &= ~SDHCI_INT_BUS_POWER; + + sdhci_writel(host, mask, SDHCI_INT_ENABLE); +} + +static void gl9755_set_power(struct sdhci_host *host, unsigned char mode, + unsigned short vdd) +{ + u8 pwr = 0; + + if (mode != MMC_POWER_OFF) { + pwr = sdhci_get_vdd_value(vdd); + if (!pwr) + WARN(1, "%s: Invalid vdd %#x\n", mmc_hostname(host->mmc), vdd); + pwr |= SDHCI_VDD2_POWER_180; + } + + if (host->pwr == pwr) + return; + + host->pwr = pwr; + + if (pwr == 0) { + sdhci_gli_overcurrent_event_enable(host, false); + sdhci_writeb(host, 0, SDHCI_POWER_CONTROL); + } else { + sdhci_gli_overcurrent_event_enable(host, false); + sdhci_writeb(host, 0, SDHCI_POWER_CONTROL); + + pwr |= (SDHCI_POWER_ON | SDHCI_VDD2_POWER_ON); + + sdhci_writeb(host, pwr & 0xf, SDHCI_POWER_CONTROL); + /* wait stable */ + mdelay(5); + sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL); + /* wait stable */ + mdelay(5); + sdhci_gli_overcurrent_event_enable(host, true); + } +} + +static bool sdhci_wait_clock_stable(struct sdhci_host *host) +{ + u16 clk = 0; + + if (read_poll_timeout_atomic(sdhci_readw, clk, (clk & SDHCI_CLOCK_INT_STABLE), + 10, 20000, false, host, SDHCI_CLOCK_CONTROL)) { + pr_err("%s: Internal clock never stabilised.\n", mmc_hostname(host->mmc)); + sdhci_dumpregs(host); + return false; + } + return true; +} + +static void sdhci_gli_uhs2_reset_sd_tran(struct sdhci_host *host) +{ + /* do this on UHS2 mode */ + if (host->mmc->uhs2_sd_tran) { + sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_SD); + sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); + sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); + sdhci_uhs2_clear_set_irqs(host, + SDHCI_INT_ALL_MASK, + SDHCI_UHS2_INT_ERROR_MASK); + } +} + +static void sdhci_gl9755_reset(struct sdhci_host *host, u8 mask) +{ + u16 clk_ctrl; + u16 ctrl2; + u8 rst; + + /* need internal clock */ + if (mask & SDHCI_RESET_ALL) { + ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); + clk_ctrl = sdhci_readw(host, SDHCI_CLOCK_CONTROL); + + if ((ctrl2 & SDHCI_CTRL_V4_MODE) && + (ctrl2 & SDHCI_CTRL_UHS2_ENABLE)) { + sdhci_writew(host, + SDHCI_CLOCK_INT_EN, + SDHCI_CLOCK_CONTROL); + } else { + sdhci_writew(host, + SDHCI_CLOCK_INT_EN, + SDHCI_CLOCK_CONTROL); + sdhci_wait_clock_stable(host); + sdhci_writew(host, + SDHCI_CTRL_V4_MODE, + SDHCI_HOST_CONTROL2); + } + } + + sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET); + + /* reset sd-tran on UHS2 mode if need to reset cmd/data */ + if ((mask & SDHCI_RESET_CMD) | (mask & SDHCI_RESET_DATA)) + sdhci_gli_uhs2_reset_sd_tran(host); + + if (mask & SDHCI_RESET_ALL) + host->clock = 0; + + /* hw clears the bit when it's done */ + if (read_poll_timeout_atomic(sdhci_readb, rst, !(rst & mask), + 10, 100000, false, host, SDHCI_SOFTWARE_RESET)) { + pr_err("%s: Reset 0x%x never completed.\n", mmc_hostname(host->mmc), (int)mask); + sdhci_dumpregs(host); + /* manual clear */ + sdhci_writeb(host, 0, SDHCI_SOFTWARE_RESET); + return; + } +} + static inline void gl9767_vhs_read(struct pci_dev *pdev) { u32 vhs_enable; @@ -1086,6 +1308,7 @@ static int gli_probe_slot_gl9755(struct sdhci_pci_slot *slot) gli_pcie_enable_msi(slot); slot->host->mmc->caps2 |= MMC_CAP2_NO_SDIO; sdhci_enable_v4_mode(host); + gl9755_vendor_init(host); return 0; } @@ -1524,17 +1747,24 @@ static const struct sdhci_ops sdhci_gl9755_ops = { .read_w = sdhci_gli_readw, .read_b = sdhci_gli_readb, .set_clock = sdhci_gl9755_set_clock, + .set_power = gl9755_set_power, .enable_dma = sdhci_pci_enable_dma, .set_bus_width = sdhci_set_bus_width, - .reset = sdhci_reset, + .reset = sdhci_gl9755_reset, .set_uhs_signaling = sdhci_set_uhs_signaling, .voltage_switch = sdhci_gli_voltage_switch, + .dump_uhs2_regs = sdhci_uhs2_dump_regs, + .set_timeout = sdhci_uhs2_set_timeout, + .irq = sdhci_uhs2_irq, + .uhs2_pre_detect_init = sdhci_gli_pre_detect_init, }; const struct sdhci_pci_fixes sdhci_gl9755 = { .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC, .quirks2 = SDHCI_QUIRK2_BROKEN_DDR50, .probe_slot = gli_probe_slot_gl9755, + .add_host = sdhci_pci_uhs2_add_host, + .remove_host = sdhci_pci_uhs2_remove_host, .ops = &sdhci_gl9755_ops, #ifdef CONFIG_PM_SLEEP .resume = sdhci_pci_gli_resume,