diff mbox

[edk2,v4,11/11] PL180: set variable length for CMD6 and ACMD51

Message ID 1478618476-12608-12-git-send-email-haojian.zhuang@linaro.org
State New
Headers show

Commit Message

Haojian Zhuang Nov. 8, 2016, 3:21 p.m. UTC 
Since CMD6 & ACMD51 needs to read data size less than 512, proper
variable length should be set.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Tested-by: Ryan Harkin <ryan.harkin@linaro.org>

---
 ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c | 14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)

-- 
2.7.4

_______________________________________________
edk2-devel mailing list
edk2-devel@lists.01.org
https://lists.01.org/mailman/listinfo/edk2-devel
diff mbox

Patch

diff --git a/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c b/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c
index 4d839e7..b2ba4c0 100644
--- a/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c
+++ b/ArmPlatformPkg/Drivers/PL180MciDxe/PL180Mci.c
@@ -63,11 +63,6 @@  MciIsReadOnly (
   return (MmioRead32 (FixedPcdGet32 (PcdPL180SysMciRegAddress)) & SYS_MCI_WPROT);
 }
 
-#if 0
-//Note: This function has been commented out because it is not used yet.
-//      This function could be used to remove the hardcoded BlockLen used
-//      in MciPrepareDataPath
-
 // Convert block size to 2^n
 STATIC
 UINT32
@@ -87,7 +82,6 @@  GetPow2BlockLen (
 
   return Pow2BlockLen;
 }
-#endif
 
 VOID
 MciPrepareDataPath (
@@ -129,12 +123,20 @@  MciSendCommand (
   } else if (MmcCmd == MMC_CMD6) {
     MmioWrite32 (MCI_DATA_TIMER_REG, 0xFFFFFFF);
     MmioWrite32 (MCI_DATA_LENGTH_REG, 64);
+#ifndef USE_STREAM
+    MmioWrite32 (MCI_DATA_CTL_REG, MCI_DATACTL_ENABLE | MCI_DATACTL_CARD_TO_CONT | GetPow2BlockLen (64));
+#else
     MmioWrite32 (MCI_DATA_CTL_REG, MCI_DATACTL_ENABLE | MCI_DATACTL_CARD_TO_CONT | MCI_DATACTL_STREAM_TRANS);
+#endif
   } else if (MmcCmd == MMC_ACMD51) {
     MmioWrite32 (MCI_DATA_TIMER_REG, 0xFFFFFFF);
     /* SCR register is 8 bytes long. */
     MmioWrite32 (MCI_DATA_LENGTH_REG, 8);
+#ifndef USE_STREAM
+    MmioWrite32 (MCI_DATA_CTL_REG, MCI_DATACTL_ENABLE | MCI_DATACTL_CARD_TO_CONT | GetPow2BlockLen (8));
+#else
     MmioWrite32 (MCI_DATA_CTL_REG, MCI_DATACTL_ENABLE | MCI_DATACTL_CARD_TO_CONT | MCI_DATACTL_STREAM_TRANS);
+#endif
   }
 
   // Create Command for PL180