| Message ID | 20161122054824.16974-2-f.fainelli@gmail.com |
|---|---|
| State | New |
| Headers | show |
On Monday, November 21, 2016 9:48:20 PM CET Florian Fainelli wrote: > This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10, > please pull the following: > > - Rafal adds support for the Netgear R8500 routers, adds basic support > for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex > A7). He also enables the UART on the Netgear R8000 and restructures the > include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes > which enables USB 3.0 on BCM5301X devices that support it. Finally he adds > support for the TP-LINK Archer C9 V1 router. > > - Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates > the bcm958625k reference board to have it enabled > > - Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using > a BCM47094) > > - Scott fixes the pinctrl names in the Cygnus DTS files > > - Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc > SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds > the node for the OTP controller found on Cygnus SoCs > > - Dhananjay enables the GPIO B controller on Norstarh Plus SoCs > > - Eric defines standard pinctrl groups in the BCM2835 GPIO node > > - Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes > to use their appropriate pinctrl functions > > - Linus adds names for the Raspberry Pi GPIO lines based on the datasheet > > - Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block > > - Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and > Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally > adds names for the Raspberry Zero GPIO lines > Pulled into next/dt, thanks! Arnd _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On Monday, November 21, 2016 9:48:20 PM CET Florian Fainelli wrote:
> 34 files changed, 1440 insertions(+), 29 deletions(-)
One follow-up: as this was a relatively big branch, it would have
been nice to get parts of it a little earlier. I see that the
raspberry-pi changes make up about half of it and came fairly
late, but the rest apparently was ready much earlier.
If you have the choice between waiting a little longer to
send all the changes at once, and sending off a good chunk
a little earlier, better send multiple sets of pull requests.
Arnd
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
On 11/30/2016 01:27 PM, Arnd Bergmann wrote: > On Monday, November 21, 2016 9:48:20 PM CET Florian Fainelli wrote: >> 34 files changed, 1440 insertions(+), 29 deletions(-) > > One follow-up: as this was a relatively big branch, it would have > been nice to get parts of it a little earlier. I see that the > raspberry-pi changes make up about half of it and came fairly > late, but the rest apparently was ready much earlier. > > If you have the choice between waiting a little longer to > send all the changes at once, and sending off a good chunk > a little earlier, better send multiple sets of pull requests. I was trying to minimize the number of pull requests for you to pull, but what you are saying makes perfect sense and helps on many aspects. Thanks a lot for your feedback! -- Florian _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The following changes since commit 1001354ca34179f3db924eb66672442a173147dc: Linux 4.9-rc1 (2016-10-15 12:17:50 -0700) are available in the git repository at: http://github.com/Broadcom/stblinux.git tags/arm-soc/for-4.10/devicetree for you to fetch changes up to 509f8342993be7ce2938edacec05b6e8d780c83e: Merge tag 'bcm2835-dt-next-2016-11-18' into devicetree/next (2016-11-21 21:03:18 -0800) ---------------------------------------------------------------- This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10, please pull the following: - Rafal adds support for the Netgear R8500 routers, adds basic support for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex A7). He also enables the UART on the Netgear R8000 and restructures the include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes which enables USB 3.0 on BCM5301X devices that support it. Finally he adds support for the TP-LINK Archer C9 V1 router. - Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates the bcm958625k reference board to have it enabled - Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using a BCM47094) - Scott fixes the pinctrl names in the Cygnus DTS files - Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds the node for the OTP controller found on Cygnus SoCs - Dhananjay enables the GPIO B controller on Norstarh Plus SoCs - Eric defines standard pinctrl groups in the BCM2835 GPIO node - Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes to use their appropriate pinctrl functions - Linus adds names for the Raspberry Pi GPIO lines based on the datasheet - Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block - Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally adds names for the Raspberry Zero GPIO lines ---------------------------------------------------------------- Dan Haab (2): ARM: BCM5301X: Add DT for Luxul XAP-1510 ARM: BCM5301X: Add DT for Luxul XWR-3100 Eric Anholt (1): ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node. Florian Fainelli (1): Merge tag 'bcm2835-dt-next-2016-11-18' into devicetree/next Gerd Hoffmann (6): pinctrl: bcm2835: add pull defines to dt bindings ARM: dts: bcm283x: add pinctrl group to &pwm, drop pins from &gpio ARM: dts: bcm283x: add pinctrl group to &i2c0, drop pins from &gpio ARM: dts: bcm283x: add pinctrl group to &i2c1, drop pins from &gpio ARM: dts: bcm283x: add pinctrl group to &sdhci, drop pins from &gpio ARM: dts: bcm283x: drop alt3 from &gpio Jonathan Richardson (3): ARM: dts: Enable Broadcom iProc mailbox controller ARM: dts: Enable interrupt support for cygnus crmu gpio driver ARM: dts: Add node for Broadcom OTP controller driver Kamal Dasu (1): ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes Linus Walleij (1): ARM: bcm2835: Add names for the Raspberry Pi GPIO lines Martin Sperl (2): dt: bindings: add thermal device driver for bcm2835 ARM: bcm2835: dts: add thermal node to device-tree of bcm283x Rafał Miłecki (7): ARM: BCM5301X: Add DT for Netgear R8500 ARM: BCM5301X: Add basic dts for BCM53573 based Tenda AC9 ARM: BCM5301X: Add separated DTS include file for BCM47094 ARM: BCM5301X: Enable UART on Netgear R8000 ARM: BCM5301X: Specify USB 3.0 PHY in DT ARM: BCM53573: Specify PMU and its ILP clock in the DT ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1 Scott Branden (1): ARM: dts: cygnus: fix naming of pinctrl node Stefan Wahren (4): DT: binding: bcm2835-mbox: fix address typo in example ARM: dts: bcm283x: fix typo in mailbox address ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines ARM: bcm2835: Add names for the RPi Zero GPIO lines Yendapally Reddy Dhananjaya Reddy (1): ARM: dts: enable GPIO-b for Broadcom NSP .../bindings/mailbox/brcm,bcm2835-mbox.txt | 2 +- .../bindings/thermal/brcm,bcm2835-thermal.txt | 17 ++ arch/arm/boot/dts/Makefile | 6 + arch/arm/boot/dts/bcm-cygnus.dtsi | 21 +- arch/arm/boot/dts/bcm-nsp.dtsi | 41 +++- arch/arm/boot/dts/bcm2835-rpi-a-plus.dts | 67 ++++++- arch/arm/boot/dts/bcm2835-rpi-a.dts | 69 ++++++- arch/arm/boot/dts/bcm2835-rpi-b-plus.dts | 68 ++++++- arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 68 ++++++- arch/arm/boot/dts/bcm2835-rpi-b.dts | 69 ++++++- arch/arm/boot/dts/bcm2835-rpi-zero.dts | 67 ++++++- arch/arm/boot/dts/bcm2835-rpi.dtsi | 15 +- arch/arm/boot/dts/bcm2835.dtsi | 6 + arch/arm/boot/dts/bcm2836-rpi-2-b.dts | 2 +- arch/arm/boot/dts/bcm2836.dtsi | 6 + arch/arm/boot/dts/bcm283x.dtsi | 212 ++++++++++++++++++++- arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts | 64 +++++++ arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts | 2 +- arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts | 2 +- arch/arm/boot/dts/bcm4709-netgear-r7000.dts | 2 +- arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 6 +- arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts | 114 +++++++++++ arch/arm/boot/dts/bcm4709.dtsi | 11 ++ arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 3 +- arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts | 111 +++++++++++ arch/arm/boot/dts/bcm47094-netgear-r8500.dts | 103 ++++++++++ arch/arm/boot/dts/bcm47094.dtsi | 17 ++ arch/arm/boot/dts/bcm47189-tenda-ac9.dts | 74 +++++++ arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi | 13 ++ arch/arm/boot/dts/bcm5301x.dtsi | 7 + arch/arm/boot/dts/bcm53573.dtsi | 159 ++++++++++++++++ arch/arm/boot/dts/bcm958625k.dts | 34 ++++ drivers/pinctrl/bcm/pinctrl-bcm2835.c | 6 - include/dt-bindings/pinctrl/bcm2835.h | 5 + 34 files changed, 1440 insertions(+), 29 deletions(-) create mode 100644 Documentation/devicetree/bindings/thermal/brcm,bcm2835-thermal.txt create mode 100644 arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts create mode 100644 arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts create mode 100644 arch/arm/boot/dts/bcm4709.dtsi create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts create mode 100644 arch/arm/boot/dts/bcm47094-netgear-r8500.dts create mode 100644 arch/arm/boot/dts/bcm47094.dtsi create mode 100644 arch/arm/boot/dts/bcm47189-tenda-ac9.dts create mode 100644 arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi create mode 100644 arch/arm/boot/dts/bcm53573.dtsi