diff mbox series

[v3] arm64: dts: qcom: sa8775p: Populate additional UART DT nodes

Message ID 20241007091407.13798-1-quic_vdadhani@quicinc.com
State Accepted
Commit 34a407316b7d37e5697c906b15bfdcafa3f6383c
Headers show
Series [v3] arm64: dts: qcom: sa8775p: Populate additional UART DT nodes | expand

Commit Message

Viken Dadhaniya Oct. 7, 2024, 9:14 a.m. UTC 
Currently, UART configuration is populated for only a few SEs
(Serial Engines) in the sa8775p DTSI file. Since every SE can
support the UART protocol, usecase or client should have the flexibility
to enable required SE for UART depending on the specific board version.

Hence, populate UART configurations for the remaining SEs in the
sa8775p SoC.

Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
---
v2 -> v3:

- Modifed commit log as requested by Dmitry.

v2 Link: https://lore.kernel.org/lkml/20240911151447.27544-1-quic_vdadhani@quicinc.com/

v1 -> v2:

- Modifed commit log as requested by Krzysztof.
- Added co-developed-by tag.

v1 Link: https://lore.kernel.org/linux-arm-msm/98e7dc28-4413-4247-bad1-98b529f6d62d@kernel.org/T/
---
---
 arch/arm64/boot/dts/qcom/sa8775p.dtsi | 231 ++++++++++++++++++++++++++
 1 file changed, 231 insertions(+)

Comments

Bjorn Andersson Oct. 16, 2024, 3:32 p.m. UTC | #1 
On Mon, 07 Oct 2024 14:44:07 +0530, Viken Dadhaniya wrote:
> Currently, UART configuration is populated for only a few SEs
> (Serial Engines) in the sa8775p DTSI file. Since every SE can
> support the UART protocol, usecase or client should have the flexibility
> to enable required SE for UART depending on the specific board version.
> 
> Hence, populate UART configurations for the remaining SEs in the
> sa8775p SoC.
> 
> [...]

Applied, thanks!

[1/1] arm64: dts: qcom: sa8775p: Populate additional UART DT nodes
      commit: 34a407316b7d37e5697c906b15bfdcafa3f6383c

Best regards,
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index e8dbc8d820a6..0c95a23aecec 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -1,6 +1,7 @@ 
 // SPDX-License-Identifier: BSD-3-Clause
 /*
  * Copyright (c) 2023, Linaro Limited
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #include <dt-bindings/interconnect/qcom,icc.h>
@@ -905,6 +906,21 @@ 
 				status = "disabled";
 			};
 
+			uart14: serial@880000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00880000 0x0 0x4000>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c15: i2c@884000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x884000 0x0 0x4000>;
@@ -947,6 +963,21 @@ 
 				status = "disabled";
 			};
 
+			uart15: serial@884000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00884000 0x0 0x4000>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c16: i2c@888000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x888000 0x0 0x4000>;
@@ -989,6 +1020,21 @@ 
 				status = "disabled";
 			};
 
+			uart16: serial@888000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00888000 0x0 0x4000>;
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c17: i2c@88c000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x88c000 0x0 0x4000>;
@@ -1088,6 +1134,21 @@ 
 				status = "disabled";
 			};
 
+			uart18: serial@890000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00890000 0x0 0x4000>;
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c19: i2c@894000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x894000 0x0 0x4000>;
@@ -1130,6 +1191,21 @@ 
 				status = "disabled";
 			};
 
+			uart19: serial@894000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00894000 0x0 0x4000>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c20: i2c@898000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x898000 0x0 0x4000>;
@@ -1171,6 +1247,22 @@ 
 				power-domains = <&rpmhpd SA8775P_CX>;
 				status = "disabled";
 			};
+
+			uart20: serial@898000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00898000 0x0 0x4000>;
+				interrupts = <GIC_SPI 834 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 		};
 
 		qupv3_id_0: geniqup@9c0000 {
@@ -1227,6 +1319,21 @@ 
 				status = "disabled";
 			};
 
+			uart0: serial@980000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x980000 0x0 0x4000>;
+				interrupts = <GIC_SPI 550 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c1: i2c@984000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x984000 0x0 0x4000>;
@@ -1269,6 +1376,21 @@ 
 				status = "disabled";
 			};
 
+			uart1: serial@984000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x984000 0x0 0x4000>;
+				interrupts = <GIC_SPI 551 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c2: i2c@988000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x988000 0x0 0x4000>;
@@ -1311,6 +1433,21 @@ 
 				status = "disabled";
 			};
 
+			uart2: serial@988000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x988000 0x0 0x4000>;
+				interrupts = <GIC_SPI 529 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c3: i2c@98c000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x98c000 0x0 0x4000>;
@@ -1353,6 +1490,21 @@ 
 				status = "disabled";
 			};
 
+			uart3: serial@98c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x98c000 0x0 0x4000>;
+				interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c4: i2c@990000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x990000 0x0 0x4000>;
@@ -1395,6 +1547,21 @@ 
 				status = "disabled";
 			};
 
+			uart4: serial@990000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x990000 0x0 0x4000>;
+				interrupts = <GIC_SPI 531 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_0 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c5: i2c@994000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x994000 0x0 0x4000>;
@@ -1507,6 +1674,22 @@ 
 				status = "disabled";
 			};
 
+			uart7: serial@a80000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00a80000 0x0 0x4000>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				interconnect-names = "qup-core", "qup-config";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
+				power-domains = <&rpmhpd SA8775P_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				status = "disabled";
+			};
+
 			i2c8: i2c@a84000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0xa84000 0x0 0x4000>;
@@ -1549,6 +1732,22 @@ 
 				status = "disabled";
 			};
 
+			uart8: serial@a84000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				interconnect-names = "qup-core", "qup-config";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
+				power-domains = <&rpmhpd SA8775P_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				status = "disabled";
+			};
+
 			i2c9: i2c@a88000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0xa88000 0x0 0x4000>;
@@ -1706,6 +1905,22 @@ 
 				status = "disabled";
 			};
 
+			uart11: serial@a90000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				interconnect-names = "qup-core", "qup-config";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
+				power-domains = <&rpmhpd SA8775P_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				status = "disabled";
+			};
+
 			i2c12: i2c@a94000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0xa94000 0x0 0x4000>;
@@ -1838,6 +2053,22 @@ 
 				power-domains = <&rpmhpd SA8775P_CX>;
 				status = "disabled";
 			};
+
+			uart21: serial@b80000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00b80000 0x0 0x4000>;
+				interrupts = <GIC_SPI 831 IRQ_TYPE_LEVEL_HIGH>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP3_S0_CLK>;
+				interconnect-names = "qup-core", "qup-config";
+				interconnects = <&clk_virt MASTER_QUP_CORE_3 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_3 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_3 QCOM_ICC_TAG_ALWAYS>;
+				power-domains = <&rpmhpd SA8775P_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				status = "disabled";
+			};
 		};
 
 		rng: rng@10d2000 {