diff mbox series

[4/5] arm64: dts: qcom: move common parts for qcs8300-ride variants into a .dtsi

Message ID 20241010-dts_qcs8300-v1-4-bf5acf05830b@quicinc.com
State New
Headers show
Series Enable ethernet for qcs8300 | expand

Commit Message

Yijie Yang Oct. 10, 2024, 2:57 a.m. UTC 
In order to support multiple revisions of the qcs8300-ride board, create
a .dtsi containing the common parts and split out the ethernet bits into
the actual board file as they will change in revision 2.

Signed-off-by: Yijie Yang <quic_yijiyang@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs8300-ride.dts  | 373 +----------------------------
 arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi | 364 ++++++++++++++++++++++++++++
 2 files changed, 377 insertions(+), 360 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
index b1c9f2cb9749..9b9922f1fcc6 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
@@ -5,375 +5,28 @@ 
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-
-#include "qcs8300.dtsi"
+#include "qcs8300-ride.dtsi"
 / {
 	model = "Qualcomm Technologies, Inc. QCS8300 Ride";
 	compatible = "qcom,qcs8300-ride", "qcom,qcs8300";
 	chassis-type = "embedded";
-
-	aliases {
-		serial0 = &uart7;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	clocks {
-		xo_board_clk: xo-board-clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <38400000>;
-		};
-
-		sleep_clk: sleep-clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32000>;
-		};
-	};
-};
-
-&apps_rsc {
-	regulators-0 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "a";
-
-		vreg_s4a: smps4 {
-			regulator-name = "vreg_s4a";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_s9a: smps9 {
-			regulator-name = "vreg_s9a";
-			regulator-min-microvolt = <1352000>;
-			regulator-max-microvolt = <1352000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l3a: ldo3 {
-			regulator-name = "vreg_l3a";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l4a: ldo4 {
-			regulator-name = "vreg_l4a";
-			regulator-min-microvolt = <880000>;
-			regulator-max-microvolt = <912000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l5a: ldo5 {
-			regulator-name = "vreg_l5a";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6a: ldo6 {
-			regulator-name = "vreg_l6a";
-			regulator-min-microvolt = <880000>;
-			regulator-max-microvolt = <912000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l7a: ldo7 {
-			regulator-name = "vreg_l7a";
-			regulator-min-microvolt = <880000>;
-			regulator-max-microvolt = <912000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8a: ldo8 {
-			regulator-name = "vreg_l8a";
-			regulator-min-microvolt = <2504000>;
-			regulator-max-microvolt = <2960000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l9a: ldo9 {
-			regulator-name = "vreg_l9a";
-			regulator-min-microvolt = <2970000>;
-			regulator-max-microvolt = <3072000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
-
-	regulators-1 {
-		compatible = "qcom,pmm8654au-rpmh-regulators";
-		qcom,pmic-id = "c";
-
-		vreg_s5c: smps5 {
-			regulator-name = "vreg_s5c";
-			regulator-min-microvolt = <1104000>;
-			regulator-max-microvolt = <1104000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l1c: ldo1 {
-			regulator-name = "vreg_l1c";
-			regulator-min-microvolt = <300000>;
-			regulator-max-microvolt = <500000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l2c: ldo2 {
-			regulator-name = "vreg_l2c";
-			regulator-min-microvolt = <900000>;
-			regulator-max-microvolt = <904000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l4c: ldo4 {
-			regulator-name = "vreg_l4c";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l6c: ldo6 {
-			regulator-name = "vreg_l6c";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l7c: ldo7 {
-			regulator-name = "vreg_l7c";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l8c: ldo8 {
-			regulator-name = "vreg_l8c";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-
-		vreg_l9c: ldo9 {
-			regulator-name = "vreg_l9c";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-			regulator-allow-set-load;
-			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
-						   RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
 };
 
 &ethernet0 {
 	phy-mode = "sgmii";
-	phy-handle = <&sgmii_phy0>;
-
-	pinctrl-0 = <&ethernet0_default>;
-	pinctrl-names = "default";
-
-	snps,mtl-rx-config = <&mtl_rx_setup>;
-	snps,mtl-tx-config = <&mtl_tx_setup>;
-	snps,ps-speed = <1000>;
-
-	status = "okay";
-
-	mdio {
-		compatible = "snps,dwmac-mdio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		sgmii_phy0: phy@8 {
-			compatible = "ethernet-phy-id0141.0dd4";
-			reg = <0x8>;
-			device_type = "ethernet-phy";
-			interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
-			reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <11000>;
-			reset-deassert-us = <70000>;
-		};
-	};
-
-	mtl_rx_setup: rx-queues-config {
-		snps,rx-queues-to-use = <4>;
-		snps,rx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x0>;
-			snps,route-up;
-			snps,priority = <0x1>;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-			snps,map-to-dma-channel = <0x1>;
-			snps,route-ptp;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x2>;
-			snps,route-avcp;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,map-to-dma-channel = <0x3>;
-			snps,priority = <0xc>;
-		};
-	};
-
-	mtl_tx_setup: tx-queues-config {
-		snps,tx-queues-to-use = <4>;
-		snps,tx-sched-sp;
-
-		queue0 {
-			snps,dcb-algorithm;
-		};
-
-		queue1 {
-			snps,dcb-algorithm;
-		};
-
-		queue2 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-
-		queue3 {
-			snps,avb-algorithm;
-			snps,send_slope = <0x1000>;
-			snps,idle_slope = <0x1000>;
-			snps,high_credit = <0x3e800>;
-			snps,low_credit = <0xffc18000>;
-		};
-	};
-};
-
-&gcc {
-	clocks = <&rpmhcc RPMH_CXO_CLK>,
-		 <&sleep_clk>,
-		 <0>,
-		 <0>,
-		 <0>,
-		 <0>,
-		 <0>,
-		 <0>,
-		 <0>,
-		 <0>;
-};
-
-&qupv3_id_0 {
-	status = "okay";
 };
 
-&remoteproc_adsp {
-	firmware-name = "qcom/qcs8300/adsp.mbn";
-	status = "okay";
-};
-
-&remoteproc_cdsp {
-	firmware-name = "qcom/qcs8300/cdsp0.mbn";
-	status = "okay";
-};
-
-&remoteproc_gpdsp {
-	firmware-name = "qcom/qcs8300/gpdsp0.mbn";
-	status = "okay";
-};
-
-&rpmhcc {
-	clocks = <&xo_board_clk>;
-	clock-names = "xo";
-};
-
-&serdes0 {
-	phy-supply = <&vreg_l5a>;
-	status = "okay";
-};
-
-&tlmm {
-	ethernet0_default: ethernet0-default-state {
-		ethernet0_mdc: ethernet0-mdc-pins {
-			pins = "gpio5";
-			function = "emac0_mdc";
-			drive-strength = <16>;
-			bias-pull-up;
-		};
-
-		ethernet0_mdio: ethernet0-mdio-pins {
-			pins = "gpio6";
-			function = "emac0_mdio";
-			drive-strength = <16>;
-			bias-pull-up;
-		};
+&mdio {
+	compatible = "snps,dwmac-mdio";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	sgmii_phy0: phy@8 {
+		compatible = "ethernet-phy-id0141.0dd4";
+		reg = <0x8>;
+		device_type = "ethernet-phy";
+		interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <11000>;
+		reset-deassert-us = <70000>;
 	};
 };
-
-&uart7 {
-	status = "okay";
-};
-
-&ufs_mem_hc {
-	reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
-	vcc-supply = <&vreg_l8a>;
-	vcc-max-microamp = <1100000>;
-	vccq-supply = <&vreg_l4c>;
-	vccq-max-microamp = <1200000>;
-	status = "okay";
-};
-
-&ufs_mem_phy {
-	vdda-phy-supply = <&vreg_l4a>;
-	vdda-pll-supply = <&vreg_l5a>;
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi b/arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi
new file mode 100644
index 000000000000..e6099f7d80cb
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi
@@ -0,0 +1,364 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "qcs8300.dtsi"
+/ {
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0: 115200n8";
+	};
+
+	clocks {
+		xo_board_clk: xo-board-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <38400000>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32000>;
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s4a: smps4 {
+			regulator-name = "vreg_s4a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s9a: smps9 {
+			regulator-name = "vreg_s9a";
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3a: ldo3 {
+			regulator-name = "vreg_l3a";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4a: ldo4 {
+			regulator-name = "vreg_l4a";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-name = "vreg_l5a";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a: ldo6 {
+			regulator-name = "vreg_l6a";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-name = "vreg_l7a";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a: ldo8 {
+			regulator-name = "vreg_l8a";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a: ldo9 {
+			regulator-name = "vreg_l9a";
+			regulator-min-microvolt = <2970000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pmm8654au-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_s5c: smps5 {
+			regulator-name = "vreg_s5c";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <500000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c: ldo2 {
+			regulator-name = "vreg_l2c";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c: ldo4 {
+			regulator-name = "vreg_l4c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c: ldo6 {
+			regulator-name = "vreg_l6c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c: ldo8 {
+			regulator-name = "vreg_l8c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c: ldo9 {
+			regulator-name = "vreg_l9c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+			RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&ethernet0 {
+	phy-handle = <&sgmii_phy0>;
+
+	pinctrl-0 = <&ethernet0_default>;
+	pinctrl-names = "default";
+
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+	snps,ps-speed = <1000>;
+
+	status = "okay";
+
+	mdio: mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <4>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <4>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
+};
+
+&gcc {
+	clocks = <&rpmhcc RPMH_CXO_CLK>,
+	         <&sleep_clk>,
+	         <0>,
+	         <0>,
+	         <0>,
+	         <0>,
+	         <0>,
+	         <0>,
+	         <0>,
+	         <0>;
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/qcs8300/adsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/qcs8300/cdsp0.mbn";
+	status = "okay";
+};
+
+&remoteproc_gpdsp {
+	firmware-name = "qcom/qcs8300/gpdsp0.mbn";
+	status = "okay";
+};
+
+&rpmhcc {
+	clocks = <&xo_board_clk>;
+	clock-names = "xo";
+};
+
+&serdes0 {
+	phy-supply = <&vreg_l5a>;
+	status = "okay";
+};
+
+&tlmm {
+	ethernet0_default: ethernet0-default-state {
+		ethernet0_mdc: ethernet0-mdc-pins {
+			pins = "gpio5";
+			function = "emac0_mdc";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		ethernet0_mdio: ethernet0-mdio-pins {
+			pins = "gpio6";
+			function = "emac0_mdio";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+	};
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l8a>;
+	vcc-max-microamp = <1100000>;
+	vccq-supply = <&vreg_l4c>;
+	vccq-max-microamp = <1200000>;
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l4a>;
+	vdda-pll-supply = <&vreg_l5a>;
+	status = "okay";
+};
+
+&uart7 {
+	status = "okay";
+};