@@ -24142,6 +24142,13 @@ L: linux-usb@vger.kernel.org
S: Orphan
F: drivers/usb/typec/tcpm/
+USB TYPEC TUSB1046 MUX DRIVER
+M: Romain Gantois <romain.gantois@bootlin.com>
+L: linux-usb@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/usb/ti,tusb1046.yaml
+F: drivers/usb/typec/mux/tusb1046.c
+
USB UHCI DRIVER
M: Alan Stern <stern@rowland.harvard.edu>
L: linux-usb@vger.kernel.org
@@ -66,6 +66,15 @@ config TYPEC_MUX_PTN36502
Say Y or M if your system has a NXP PTN36502 Type-C redriver chip
found on some devices with a Type-C port.
+config TYPEC_MUX_TUSB1046
+ tristate "TI TUSB1046 Type-C crosspoint switch driver"
+ depends on I2C
+ help
+ Driver for the Texas Instruments TUSB1046-DCI crosspoint switch.
+ Supports flipping USB-C SuperSpeed lanes to adapt to orientation
+ changes, as well as muxing DisplayPort and sideband signals to a
+ common Type-C connector.
+
config TYPEC_MUX_WCD939X_USBSS
tristate "Qualcomm WCD939x USBSS Analog Audio Switch driver"
depends on I2C
@@ -7,4 +7,5 @@ obj-$(CONFIG_TYPEC_MUX_INTEL_PMC) += intel_pmc_mux.o
obj-$(CONFIG_TYPEC_MUX_IT5205) += it5205.o
obj-$(CONFIG_TYPEC_MUX_NB7VPQ904M) += nb7vpq904m.o
obj-$(CONFIG_TYPEC_MUX_PTN36502) += ptn36502.o
+obj-$(CONFIG_TYPEC_MUX_TUSB1046) += tusb1046.o
obj-$(CONFIG_TYPEC_MUX_WCD939X_USBSS) += wcd939x-usbss.o
new file mode 100644
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Driver for the TUSB1046-DCI USB Type-C crosspoint switch
+ *
+ * Copyright (C) 2024 Bootlin
+ */
+
+#include <linux/bits.h>
+#include <linux/i2c.h>
+#include <linux/usb/typec_mux.h>
+#include <linux/usb/typec_dp.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/err.h>
+#include <linux/of_device.h>
+#include <linux/device.h>
+
+#define TUSB1046_REG_GENERAL 0xa
+
+/* General register bits */
+#define TUSB1046_GENERAL_FLIPSEL BIT(2)
+#define TUSB1046_GENERAL_CTLSEL GENMASK(1, 0)
+
+/* Mux modes */
+#define TUSB1046_CTLSEL_DISABLED 0x0
+#define TUSB1046_CTLSEL_USB3 0x1
+#define TUSB1046_CTLSEL_4LANE_DP 0x2
+#define TUSB1046_CTLSEL_USB3_AND_2LANE_DP 0x3
+
+struct tusb1046_priv {
+ struct i2c_client *client;
+ struct typec_switch_dev *sw;
+ struct typec_mux_dev *mux;
+};
+
+static int tusb1046_mux_set(struct typec_mux_dev *mux,
+ struct typec_mux_state *state)
+{
+ struct tusb1046_priv *priv = typec_mux_get_drvdata(mux);
+ struct i2c_client *client = priv->client;
+ struct device *dev = &client->dev;
+ int mode, val;
+
+ dev_dbg(dev, "mux mode requested: %lu\n", state->mode);
+
+ val = i2c_smbus_read_byte_data(client, TUSB1046_REG_GENERAL);
+ if (val < 0) {
+ dev_err(dev, "failed to read ctlsel status, err %d\n", val);
+ return val;
+ }
+
+ switch (state->mode) {
+ case TYPEC_STATE_USB:
+ mode = TUSB1046_CTLSEL_USB3;
+ break;
+ case TYPEC_DP_STATE_C:
+ case TYPEC_DP_STATE_E:
+ mode = TUSB1046_CTLSEL_4LANE_DP;
+ break;
+ case TYPEC_DP_STATE_D:
+ mode = TUSB1046_CTLSEL_USB3_AND_2LANE_DP;
+ break;
+ case TYPEC_STATE_SAFE:
+ default:
+ mode = TUSB1046_CTLSEL_DISABLED;
+ break;
+ }
+
+ val &= ~TUSB1046_GENERAL_CTLSEL;
+ val |= mode;
+
+ return i2c_smbus_write_byte_data(client, TUSB1046_REG_GENERAL, val);
+}
+
+static int tusb1046_switch_set(struct typec_switch_dev *sw,
+ enum typec_orientation orientation)
+{
+ struct tusb1046_priv *priv = typec_switch_get_drvdata(sw);
+ struct i2c_client *client = priv->client;
+ struct device *dev = &client->dev;
+ int val;
+
+ dev_dbg(dev, "setting USB3.0 lane flip for orientation %d\n", orientation);
+
+ val = i2c_smbus_read_byte_data(client, TUSB1046_REG_GENERAL);
+ if (val < 0) {
+ dev_err(dev, "failed to read flipsel status, err %d\n", val);
+ return val;
+ }
+
+ if (orientation == TYPEC_ORIENTATION_REVERSE)
+ val |= TUSB1046_GENERAL_FLIPSEL;
+ else
+ val &= ~TUSB1046_GENERAL_FLIPSEL;
+
+ return i2c_smbus_write_byte_data(client, TUSB1046_REG_GENERAL, val);
+}
+
+static int tusb1046_i2c_probe(struct i2c_client *client)
+{
+ struct typec_switch_desc sw_desc = { };
+ struct typec_mux_desc mux_desc = { };
+ struct device *dev = &client->dev;
+ struct tusb1046_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return dev_err_probe(dev, -ENOMEM, "failed to allocate driver data\n");
+
+ priv->client = client;
+
+ sw_desc.drvdata = priv;
+ sw_desc.fwnode = dev_fwnode(dev);
+ sw_desc.set = tusb1046_switch_set;
+
+ priv->sw = typec_switch_register(dev, &sw_desc);
+ if (IS_ERR(priv->sw))
+ return dev_err_probe(dev, PTR_ERR(priv->sw), "failed to register type-c switch\n");
+
+ mux_desc.drvdata = priv;
+ mux_desc.fwnode = dev_fwnode(dev);
+ mux_desc.set = tusb1046_mux_set;
+
+ priv->mux = typec_mux_register(dev, &mux_desc);
+ if (IS_ERR(priv->mux)) {
+ typec_switch_unregister(priv->sw);
+ return dev_err_probe(dev, PTR_ERR(priv->mux), "failed to register type-c mux\n");
+ }
+
+ i2c_set_clientdata(client, priv);
+
+ return 0;
+}
+
+static void tusb1046_i2c_remove(struct i2c_client *client)
+{
+ struct tusb1046_priv *priv = i2c_get_clientdata(client);
+
+ typec_switch_unregister(priv->sw);
+ typec_mux_unregister(priv->mux);
+}
+
+static const struct of_device_id tusb1046_match_table[] = {
+ {.compatible = "ti,tusb1046"},
+ {},
+};
+
+static struct i2c_driver tusb1046_driver = {
+ .driver = {
+ .name = "tusb1046",
+ .of_match_table = tusb1046_match_table,
+ },
+ .probe = tusb1046_i2c_probe,
+ .remove = tusb1046_i2c_remove,
+};
+
+module_i2c_driver(tusb1046_driver);
+
+MODULE_DESCRIPTION("TUSB1046 USB Type-C switch driver");
+MODULE_AUTHOR("Romain Gantois <romain.gantois@bootlin.com>");
+MODULE_LICENSE("GPL");
The TUSB1046-DCI is a USB-C linear redriver crosspoint switch, which can mux SuperSpeed lanes from a Type-C connector to a USB3.0 data lane or up to 4 display port lanes. Add support for driving the TUSB1046 as a Type-C orientation switch and DisplayPort altmode multiplexer. Signed-off-by: Romain Gantois <romain.gantois@bootlin.com> --- MAINTAINERS | 7 ++ drivers/usb/typec/mux/Kconfig | 9 +++ drivers/usb/typec/mux/Makefile | 1 + drivers/usb/typec/mux/tusb1046.c | 161 +++++++++++++++++++++++++++++++++++++++ 4 files changed, 178 insertions(+)