diff mbox series

[v1,1/1] arm64: dts: qcom: x1e80100-dell-xps13-9345: Introduce retimer support

Message ID 20241030182153.16256-2-alex.vinarskis@gmail.com
State New
Headers show
Series [v1,1/1] arm64: dts: qcom: x1e80100-dell-xps13-9345: Introduce retimer support | expand

Commit Message

Aleksandrs Vinarskis Oct. 30, 2024, 6:19 p.m. UTC 
Describe x2 Parade PS8830 retimers for left and right USB Type-C ports
respectively. Adjust graphs between connectors and the PHYs accordingly,
add the voltage regulators. Dell XPS 13" 9345's DSDT describes 3rd
retimer, but its not actually present.

Regulators are _assumed_ to be correct, since:
* tlmm pins match DSDT definition.
* tlmm and pmic gpios were tested and confirmed to be powering
  off/resetting respective retimers.
* USB3.0 now works correctly in both orientation, pre and post suspend.

Derived from:
arm64: dts: qcom: x1e80100-t14s: Add external DP support

Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
---
 .../dts/qcom/x1e80100-dell-xps13-9345.dts     | 293 +++++++++++++++++-
 1 file changed, 283 insertions(+), 10 deletions(-)

Comments

Konrad Dybcio Nov. 4, 2024, 1:52 p.m. UTC | #1 
On 30.10.2024 7:19 PM, Aleksandrs Vinarskis wrote:
> Describe x2 Parade PS8830 retimers for left and right USB Type-C ports
> respectively. Adjust graphs between connectors and the PHYs accordingly,
> add the voltage regulators. Dell XPS 13" 9345's DSDT describes 3rd
> retimer, but its not actually present.
> 
> Regulators are _assumed_ to be correct, since:
> * tlmm pins match DSDT definition.
> * tlmm and pmic gpios were tested and confirmed to be powering
>   off/resetting respective retimers.
> * USB3.0 now works correctly in both orientation, pre and post suspend.
> 
> Derived from:
> arm64: dts: qcom: x1e80100-t14s: Add external DP support
> 
> Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts b/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts
index 05624226faf9..b112092fbb9f 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-dell-xps13-9345.dts
@@ -89,7 +89,15 @@  port@1 {
 					reg = <1>;
 
 					pmic_glink_ss0_ss_in: endpoint {
-						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+						remote-endpoint = <&retimer_ss0_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
 					};
 				};
 			};
@@ -118,7 +126,15 @@  port@1 {
 					reg = <1>;
 
 					pmic_glink_ss1_ss_in: endpoint {
-						remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+						remote-endpoint = <&retimer_ss1_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss1_con_sbu_out>;
 					};
 				};
 			};
@@ -166,6 +182,102 @@  vreg_nvme: regulator-nvme {
 		regulator-boot-on;
 	};
 
+	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&rtmr0_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&rtmr0_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&rtmr0_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&rtmr1_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&rtmr1_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&rtmr1_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
 	vreg_vph_pwr: regulator-vph-pwr {
 		compatible = "regulator-fixed";
 
@@ -492,9 +604,60 @@  keyboard@5 {
 
 &i2c3 {
 	clock-frequency = <400000>;
-	status = "disabled";
-	/* PS8830 Retimer @0x8 */
-	/* Unknown device @0x9 */
+	status = "okay";
+
+	/* Right-side USB Type-C port */
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x08>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK3>;
+		clock-names = "xo";
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
 };
 
 &i2c5 {
@@ -505,9 +668,61 @@  &i2c5 {
 
 &i2c7 {
 	clock-frequency = <400000>;
-	status = "disabled";
-	/* PS8830 Retimer @0x8 */
-	/* Unknown device @0x9 */
+	status = "okay";
+
+	/* Left-side USB Type-C port */
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK4>;
+		clock-names = "xo";
+
+		vdd-supply = <&vreg_rtmr1_1p15>;
+		vdd33-supply = <&vreg_rtmr1_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+		vddar-supply = <&vreg_rtmr1_1p15>;
+		vddat-supply = <&vreg_rtmr1_1p15>;
+		vddio-supply = <&vreg_rtmr1_1p8>;
+
+		reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr1_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss1_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss1_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss1_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+				};
+			};
+
+		};
+	};
 };
 
 &i2c8 {
@@ -634,6 +849,36 @@  &pcie6a_phy {
 	status = "okay";
 };
 
+&pm8550_gpios {
+	rtmr0_default: rtmr0-reset-n-active-state {
+		pins = "gpio10";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+	};
+
+	rtmr0_3p3_reg_en: rtmr0-3p3-reg-en-state {
+		pins = "gpio11";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+	};
+};
+
+&pmc8380_5_gpios {
+	rtmr0_1p15_reg_en: rtmr0-1p15-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+	};
+};
+
+&pm8550ve_9_gpios {
+	rtmr0_1p8_reg_en: rtmr0-1p8-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+	};
+};
+
 &qupv3_0 {
 	status = "okay";
 };
@@ -762,6 +1007,34 @@  wake-n-pins {
 		};
 	};
 
+	rtmr1_1p15_reg_en: rtmr1-1p15-reg-en-state {
+		pins = "gpio188";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rtmr1_1p8_reg_en: rtmr1-1p8-reg-en-state {
+		pins = "gpio175";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rtmr1_3p3_reg_en: rtmr1-3p3-reg-en-state {
+		pins = "gpio186";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rtmr1_default: rtmr1-reset-n-active-state {
+		pins = "gpio176";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	tpad_default: tpad-default-state {
 		disable-pins {
 			pins = "gpio38";
@@ -839,7 +1112,7 @@  &usb_1_ss0_dwc3_hs {
 };
 
 &usb_1_ss0_qmpphy_out {
-	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+	remote-endpoint = <&retimer_ss0_ss_in>;
 };
 
 &usb_1_ss1_hsphy {
@@ -871,5 +1144,5 @@  &usb_1_ss1_dwc3_hs {
 };
 
 &usb_1_ss1_qmpphy_out {
-	remote-endpoint = <&pmic_glink_ss1_ss_in>;
+	remote-endpoint = <&retimer_ss1_ss_in>;
 };