diff mbox series

[v4,2/3] arm64: dts: qcom: sar2130p: add support for SAR2130P

Message ID 20241102-sar2130p-dt-v4-2-60b7220fd0dd@linaro.org
State Superseded
Headers show
Series arm64: dts: qcom: add QAR2130P support | expand

Commit Message

Dmitry Baryshkov Nov. 2, 2024, 3:03 a.m. UTC
Add DT file for the Qualcomm SAR2130P platform.

Co-developed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sar2130p.dtsi | 3123 ++++++++++++++++++++++++++++++++
 1 file changed, 3123 insertions(+)

Comments

Krishna Kurapati Nov. 26, 2024, 6:02 p.m. UTC | #1
On 11/2/2024 8:33 AM, Dmitry Baryshkov wrote:
> Add DT file for the Qualcomm SAR2130P platform.
> 
> Co-developed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>   arch/arm64/boot/dts/qcom/sar2130p.dtsi | 3123 ++++++++++++++++++++++++++++++++
>   1 file changed, 3123 insertions(+)
> 

[...]

> +		usb_dp_qmpphy: phy@88e8000 {
> +			compatible = "qcom,sar2130p-qmp-usb3-dp-phy";
> +			reg = <0x0 0x088e8000 0x0 0x3000>;
> +
> +			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> +				 <&rpmhcc RPMH_CXO_CLK>,
> +				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> +				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> +			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
> +
> +			power-domains = <&gcc USB3_PHY_GDSC>;
> +
> +			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
> +				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
> +			reset-names = "phy", "common";
> +
> +			#clock-cells = <1>;
> +			#phy-cells = <1>;
> +
> +			orientation-switch;
> +
> +			status = "disabled";
> +

Hi Dmitry,

  Sorry for asking this question after code got merged. I forgot about 
asking this last time when I commented on your patch and provided the HS 
Phy IRQ value.

  In SAR2130P, I remember that the lane orientation is reversed. As in 
on normal targets, if the orientatin GPIO reads "0" it means LANE_A but 
on SAR2130 it means LANE_B. Can you confirm if superspeed was tested 
only in one orientation only.

  I can push code for setting orienation properly for this target if you 
can confirm that orienation is read reverse on SAR2130P.

Regards,
Krishna,
Dmitry Baryshkov Nov. 27, 2024, 2:02 p.m. UTC | #2
On Tue, Nov 26, 2024 at 11:32:59PM +0530, Krishna Kurapati wrote:
> 
> 
> On 11/2/2024 8:33 AM, Dmitry Baryshkov wrote:
> > Add DT file for the Qualcomm SAR2130P platform.
> > 
> > Co-developed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> > Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> > ---
> >   arch/arm64/boot/dts/qcom/sar2130p.dtsi | 3123 ++++++++++++++++++++++++++++++++
> >   1 file changed, 3123 insertions(+)
> > 
> 
> [...]
> 
> > +		usb_dp_qmpphy: phy@88e8000 {
> > +			compatible = "qcom,sar2130p-qmp-usb3-dp-phy";
> > +			reg = <0x0 0x088e8000 0x0 0x3000>;
> > +
> > +			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> > +				 <&rpmhcc RPMH_CXO_CLK>,
> > +				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> > +				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> > +			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
> > +
> > +			power-domains = <&gcc USB3_PHY_GDSC>;
> > +
> > +			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
> > +				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
> > +			reset-names = "phy", "common";
> > +
> > +			#clock-cells = <1>;
> > +			#phy-cells = <1>;
> > +
> > +			orientation-switch;
> > +
> > +			status = "disabled";
> > +
> 
> Hi Dmitry,
> 
>  Sorry for asking this question after code got merged. I forgot about asking
> this last time when I commented on your patch and provided the HS Phy IRQ
> value.
> 
>  In SAR2130P, I remember that the lane orientation is reversed. As in on
> normal targets, if the orientatin GPIO reads "0" it means LANE_A but on
> SAR2130 it means LANE_B. Can you confirm if superspeed was tested only in
> one orientation only.

Thanks for the notice. I don't remember if I had USB3 or just USB2
connected to the USB-C connector. I will take a look and report
afterwards, but it might take some time.

> 
>  I can push code for setting orienation properly for this target if you can
> confirm that orienation is read reverse on SAR2130P.
> 
> Regards,
> Krishna,
Krishna Kurapati Nov. 27, 2024, 3:42 p.m. UTC | #3
On 11/27/2024 7:32 PM, Dmitry Baryshkov wrote:
> On Tue, Nov 26, 2024 at 11:32:59PM +0530, Krishna Kurapati wrote:
>>
>>
>> On 11/2/2024 8:33 AM, Dmitry Baryshkov wrote:
>>> Add DT file for the Qualcomm SAR2130P platform.
>>>
>>> Co-developed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>>> ---
>>>    arch/arm64/boot/dts/qcom/sar2130p.dtsi | 3123 ++++++++++++++++++++++++++++++++
>>>    1 file changed, 3123 insertions(+)
>>>
>>
>> [...]
>>
>>> +		usb_dp_qmpphy: phy@88e8000 {
>>> +			compatible = "qcom,sar2130p-qmp-usb3-dp-phy";
>>> +			reg = <0x0 0x088e8000 0x0 0x3000>;
>>> +
>>> +			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
>>> +				 <&rpmhcc RPMH_CXO_CLK>,
>>> +				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
>>> +				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
>>> +			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
>>> +
>>> +			power-domains = <&gcc USB3_PHY_GDSC>;
>>> +
>>> +			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
>>> +				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
>>> +			reset-names = "phy", "common";
>>> +
>>> +			#clock-cells = <1>;
>>> +			#phy-cells = <1>;
>>> +
>>> +			orientation-switch;
>>> +
>>> +			status = "disabled";
>>> +
>>
>> Hi Dmitry,
>>
>>   Sorry for asking this question after code got merged. I forgot about asking
>> this last time when I commented on your patch and provided the HS Phy IRQ
>> value.
>>
>>   In SAR2130P, I remember that the lane orientation is reversed. As in on
>> normal targets, if the orientatin GPIO reads "0" it means LANE_A but on
>> SAR2130 it means LANE_B. Can you confirm if superspeed was tested only in
>> one orientation only. >
> Thanks for the notice. I don't remember if I had USB3 or just USB2

Basically during "qmp_combo_com_init()" call, we program the orientation 
based on gpio output from ucsi:

	val = SW_PORTSELECT_MUX;
	if (qmp->orientation == TYPEC_ORIENTATION_REVERSE)
		val |= SW_PORTSELECT_VAL;
	writel(val, com + QPHY_V3_DP_COM_TYPEC_CTRL);

  On SAR2130P, the above logic is reverse. If the cable is set in normal 
orientation, the SW_PORTSELECT_VAL must be set. You can compare the 
result on some mobile target like SM8550/SM8650 vs SAR2130 to confirm 
the observation.

> connected to the USB-C connector. I will take a look and report
> afterwards, but it might take some time.
> 

  No worries. Just wanted to bring this to your notice. On day-1 of 
bring-up, I did struggle for some time to figure out that the CC 
orientation is flipped since every cable flip was working in High Speed 
as lanes were programmed reverse all the time. I didn't want you to hit 
that issue for when the orientation switch is actually enabled.

  On a side note, there were some issues found in qmp combo phy during 
stress testing which are specific to SAR2130P. I can try and fix them up 
after you confirm the above test results now that the target is actually 
present on upstream.

Regards,
Krishna,
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sar2130p.dtsi b/arch/arm64/boot/dts/qcom/sar2130p.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..56f40e8ecae561d49331e51c57581d517dbc9b51
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sar2130p.dtsi
@@ -0,0 +1,3123 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Linaro Limited
+ */
+
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,sar2130p-gcc.h>
+#include <dt-bindings/clock/qcom,sar2130p-gpucc.h>
+#include <dt-bindings/clock/qcom,sm8550-tcsr.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/interconnect/qcom,icc.h>
+#include <dt-bindings/interconnect/qcom,sar2130p-rpmh.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/phy/phy-qcom-qmp.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/power/qcom,rpmhpd.h>
+#include <dt-bindings/soc/qcom,gpr.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x0>;
+			clocks = <&cpufreq_hw 0>;
+			enable-method = "psci";
+			next-level-cache = <&l2_0>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&cpu_pd0>;
+			power-domain-names = "psci";
+			#cooling-cells = <2>;
+
+			l2_0: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+				cache-unified;
+				next-level-cache = <&l3_0>;
+
+				l3_0: l3-cache {
+					compatible = "cache";
+					cache-level = <3>;
+					cache-unified;
+				};
+			};
+		};
+
+		cpu1: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x100>;
+			clocks = <&cpufreq_hw 0>;
+			enable-method = "psci";
+			next-level-cache = <&l2_100>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&cpu_pd1>;
+			power-domain-names = "psci";
+			#cooling-cells = <2>;
+
+			l2_100: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+				cache-unified;
+				next-level-cache = <&l3_0>;
+			};
+		};
+
+		cpu2: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x200>;
+			clocks = <&cpufreq_hw 0>;
+			enable-method = "psci";
+			next-level-cache = <&l2_200>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&cpu_pd2>;
+			power-domain-names = "psci";
+			#cooling-cells = <2>;
+
+			l2_200: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+				cache-unified;
+				next-level-cache = <&l3_0>;
+			};
+		};
+
+		cpu3: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x300>;
+			clocks = <&cpufreq_hw 0>;
+			enable-method = "psci";
+			next-level-cache = <&l2_300>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&cpu_pd3>;
+			power-domain-names = "psci";
+			#cooling-cells = <2>;
+
+			l2_300: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+				cache-unified;
+				next-level-cache = <&l3_0>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			cpu_sleep_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "silver-power-collapse";
+				arm,psci-suspend-param = <0x40000003>;
+				entry-latency-us = <549>;
+				exit-latency-us = <901>;
+				min-residency-us = <1774>;
+				local-timer-stop;
+			};
+
+			cpu_sleep_1: cpu-sleep-0-1 {
+				compatible = "arm,idle-state";
+				idle-state-name = "silver-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <702>;
+				exit-latency-us = <915>;
+				min-residency-us = <4001>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			cluster_sleep_0: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41000044>;
+				entry-latency-us = <2752>;
+				exit-latency-us = <3048>;
+				min-residency-us = <6118>;
+			};
+
+			cluster_sleep_1: cluster-sleep-1 {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x41002344>;
+				entry-latency-us = <3263>;
+				exit-latency-us = <4562>;
+				min-residency-us = <8467>;
+			};
+
+			cluster_sleep_2: cluster-sleep-2 {
+				compatible = "domain-idle-state";
+				arm,psci-suspend-param = <0x4100c344>;
+				entry-latency-us = <3638>;
+				exit-latency-us = <6562>;
+				min-residency-us = <9862>;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sar2130p", "qcom,scm";
+			qcom,dload-mode = <&tcsr_mutex 0x13000>;
+			interconnects = <&system_noc MASTER_CRYPTO QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+		};
+	};
+
+	clk_virt: interconnect-0 {
+		compatible = "qcom,sar2130p-clk-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	mc_virt: interconnect-1 {
+		compatible = "qcom,sar2130p-mc-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0x80000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		cpu_pd0: power-domain-cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>, <&cpu_sleep_1>;
+		};
+
+		cpu_pd1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>, <&cpu_sleep_1>;
+		};
+
+		cpu_pd2: power-domain-cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>, <&cpu_sleep_1>;
+		};
+
+		cpu_pd3: power-domain-cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&cluster_pd>;
+			domain-idle-states = <&cpu_sleep_0>, <&cpu_sleep_1>;
+		};
+
+		cluster_pd: power-domain-cpu-cluster0 {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&cluster_sleep_0>, <&cluster_sleep_1>, <&cluster_sleep_2>;
+		};
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: hyp@80000000 {
+			reg = <0x0 0x80000000 0x0 0x600000>;
+			no-map;
+		};
+
+		xbl_dt_log_mem: xbl-dt-log@80600000 {
+			reg = <0x0 0x80600000 0x0 0x40000>;
+			no-map;
+		};
+
+		xbl_ramdump_mem: xbl-ramdump@80640000 {
+			reg = <0x0 0x80640000 0x0 0x1c0000>;
+			no-map;
+		};
+
+		aop_image_mem: aop-image@80800000 {
+			reg = <0x0 0x80800000 0x0 0x60000>;
+			no-map;
+		};
+
+		aop_cmd_db_mem: aop-cmd-db@80860000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x0 0x80860000 0x0 0x20000>;
+			no-map;
+		};
+
+		aop_config_mem: aop-config@80880000 {
+			reg = <0x0 0x80880000 0x0 0x20000>;
+			no-map;
+		};
+
+		tme_crash_dump_mem: tme-crash-dump@808a0000 {
+			reg = <0x0 0x808a0000 0x0 0x40000>;
+			no-map;
+		};
+
+		tme_log_mem: tme-log@808e0000 {
+			reg = <0x0 0x808e0000 0x0 0x4000>;
+			no-map;
+		};
+
+		uefi_log_mem: uefi-log@808e4000 {
+			reg = <0x0 0x808e4000 0x0 0x10000>;
+			no-map;
+		};
+
+		secdata_apss_mem: secdata-apss@808ff000 {
+			reg = <0x0 0x808ff000 0x0 0x1000>;
+			no-map;
+		};
+
+		smem: smem@80900000 {
+			compatible = "qcom,smem";
+			reg = <0x0 0x80900000 0x0 0x200000>;
+			hwlocks = <&tcsr_mutex 3>;
+			no-map;
+		};
+
+		cpucp_fw_mem: cpucp-fw@80b00000 {
+			reg = <0x0 0x80b00000 0x0 0x100000>;
+			no-map;
+		};
+
+		helios_ram_dump_mem: helios-ram-dump@80c00000 {
+			reg = <0x0 0x80c00000 0x0 0xe00000>;
+			no-map;
+		};
+
+		camera_mem: camera@84e00000 {
+			reg = <0x0 0x84e00000 0x0 0x800000>;
+			no-map;
+		};
+
+		video_mem: video@86f00000 {
+			reg = <0x0 0x86f00000 0x0 0x500000>;
+			no-map;
+		};
+
+		adsp_mem: adsp@87600000 {
+			reg = <0x0 0x87600000 0x0 0x1e00000>;
+			no-map;
+		};
+
+		cdsp_mem: cdsp@89400000 {
+			reg = <0x0 0x89400000 0x0 0xf00000>;
+			no-map;
+		};
+
+		ipa_fw_mem: ipa-fw@8a300000 {
+			reg = <0x0 0x8a300000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: ipa-gsi@8a3a0000 {
+			reg = <0x0 0x8a310000 0x0 0xa000>;
+			no-map;
+		};
+
+		gpu_micro_code_mem: gpu-micro-code@8a31a000 {
+			reg = <0x0 0x8a31a000 0x0 0x2000>;
+			no-map;
+		};
+
+		cvp_mem: cvp@8a400000 {
+			reg = <0x0 0x8a400000 0x0 0x700000>;
+			no-map;
+		};
+
+		xbl_sc_mem: xbl-sc@a6e00000 {
+			no-map;
+			reg = <0x0 0xa6e00000 0x0 0x40000>;
+		};
+
+		global_sync_mem: global-sync@a6f00000 {
+			no-map;
+			reg = <0x0 0xa6f00000 0x0 0x100000>;
+		};
+
+		tz_stat_mem: tz-stat@e8800000 {
+			no-map;
+			reg = <0x0 0xe8800000 0x0 0x100000>;
+		};
+
+		tags_mem: tags@e8900000 {
+			no-map;
+			reg = <0x0 0xe8900000 0x0 0x500000>;
+		};
+
+		qtee_mem: qtee@e8e00000 {
+			no-map;
+			reg = <0x0 0xe8e00000 0x0 0x500000>;
+		};
+
+		trusted_apps_mem: trusted-apps@e9300000 {
+			no-map;
+			reg = <0x0 0xe9300000 0x0 0xc00000>;
+		};
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_LPASS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		smp2p_adsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_adsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-cdsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <94>, <432>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_CDSP
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <5>;
+
+		smp2p_cdsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_cdsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,sar2130p-gcc";
+			reg = <0x0 0x00100000 0x0 0x1f4200>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&sleep_clk>,
+				 <&pcie0_phy>,
+				 <&pcie1_phy>,
+				 <&usb_dp_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
+		};
+
+		sdhc_1: mmc@7c4000 {
+			compatible = "qcom,sar2130p-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x0 0x007c4000 0x0 0x1000>,
+			      <0x0 0x007c5000 0x0 0x1000>;
+			reg-names = "hc", "cqhci";
+
+			iommus = <&apps_smmu 0x160 0x0>;
+			interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
+			interconnects = <&system_noc MASTER_SDCC_1 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_SDCC_1 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "sdhc-ddr","cpu-sdhc";
+			power-domains = <&rpmhpd RPMHPD_CX>;
+			operating-points-v2 = <&sdhc1_opp_table>;
+
+			pinctrl-0 = <&sdc1_default>;
+			pinctrl-1 = <&sdc1_sleep>;
+			pinctrl-names = "default", "sleep";
+
+			bus-width = <8>;
+			non-removable;
+			supports-cqe;
+
+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			mmc-hs400-enhanced-strobe;
+
+			status = "disabled";
+
+			sdhc1_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+					opp-peak-kBps = <500000 200000>;
+					opp-avg-kBps = <104000 0>;
+				};
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+					opp-peak-kBps = <2500000 1000000>;
+					opp-avg-kBps = <400000 0>;
+				};
+			};
+		};
+
+		gpi_dma0: dma-controller@900000 {
+			compatible = "qcom,sar2130p-gpi-dma", "qcom,sm6350-gpi-dma";
+			reg = <0x0 0x00900000 0x0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <3>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x76 0x0>;
+
+			status = "disabled";
+		};
+
+		qupv3_id_0: geniqup@9c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x009c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x63 0x0>;
+			interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+					 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "qup-core";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00980000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00980000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs0>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00984000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00984000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00988000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00988000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+
+			i2c3: i2c@98c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x0098c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x0098c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs0>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00990000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00990000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs0>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00994000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00994000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_0 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_0 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gpi_dma1: dma-controller@a00000 {
+			compatible = "qcom,sar2130p-gpi-dma", "qcom,sm6350-gpi-dma";
+			#dma-cells = <3>;
+			reg = <0x0 0x00a00000 0x0 0x60000>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x16 0x0>;
+
+			status = "disabled";
+		};
+
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x3 0x0>;
+			interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+					 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "qup-core";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			i2c6: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi6: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c7: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-0 = <&qup_i2c7_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi7: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			uart7: serial@a84000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-0 = <&qup_uart7_default>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+
+				status = "disabled";
+			};
+
+			i2c8: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-0 = <&qup_i2c8_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi8: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c9: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-0 = <&qup_i2c9_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi9: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c10: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-0 = <&qup_i2c10_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi10: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c11: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a94000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-0 = <&qup_i2c11_data_clk>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
+			spi11: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a94000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
+				pinctrl-names = "default";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_A2NOC_SNOC QCOM_ICC_TAG_ALWAYS
+						 &gem_noc SLAVE_LLCC QCOM_ICC_TAG_ALWAYS>,
+						<&system_noc MASTER_QUP_1 QCOM_ICC_TAG_ALWAYS
+						 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			uart11: serial@a94000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0x0 0x00a94000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-0 = <&qup_uart11_default>;
+				pinctrl-names = "default";
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				status = "disabled";
+			};
+		};
+
+		config_noc: interconnect@1500000 {
+			compatible = "qcom,sar2130p-config-noc";
+			reg = <0x0 0x01500000 0x0 0x10>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@1680000 {
+			compatible = "qcom,sar2130p-system-noc";
+			reg = <0x0 0x01680000 0x0 0x29080>;
+			clocks = <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		pcie_noc: interconnect@16c0000 {
+			compatible = "qcom,sar2130p-pcie-anoc";
+			reg = <0x0 0x016c0000 0x0 0xa080>;
+			clocks = <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_PCIE_ANOC_AHB_CLK>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		mmss_noc: interconnect@1740000 {
+			compatible = "qcom,sar2130p-mmss-noc";
+			reg = <0x0 0x01740000 0x0 0x1f100>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		pcie0: pcie@1c00000 {
+			device_type = "pci";
+			compatible = "qcom,sar2130p-pcie", "qcom,pcie-sm8550";
+			reg = <0x0 0x01c00000 0x0 0x3000>,
+			      <0x0 0x60000000 0x0 0xf1d>,
+			      <0x0 0x60000f20 0x0 0xa8>,
+			      <0x0 0x60001000 0x0 0x1000>,
+			      <0x0 0x60100000 0x0 0x100000>,
+			      <0x0 0x01c0c000 0x0 0x1000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <0>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "noc_aggr";
+
+			interconnects = <&pcie_noc MASTER_PCIE_0 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_PCIE_0 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
+				    <0x100 &apps_smmu 0x1c01 0x1>;
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+
+			pcieport0: pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
+		};
+
+		pcie0_phy: phy@1c06000 {
+			compatible = "qcom,sar2130p-qmp-gen3x2-pcie-phy";
+			reg = <0x0 0x01c06000 0x0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_0_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_0_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie0_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		pcie1: pcie@1c08000 {
+			device_type = "pci";
+			compatible = "qcom,sar2130p-pcie", "qcom,pcie-sm8550";
+			reg = <0x0 0x01c08000 0x0 0x3000>,
+			      <0x0 0x40000000 0x0 0xf1d>,
+			      <0x0 0x40000f20 0x0 0xa8>,
+			      <0x0 0x40001000 0x0 0x1000>,
+			      <0x0 0x40100000 0x0 0x100000>,
+			      <0x0 0x01c0b000 0x0 0x1000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <1>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0",
+					  "msi1",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_PCIE_ANOC_AHB_CLK>,
+				 <&gcc GCC_QMIP_PCIE_AHB_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "noc_aggr",
+				      "cnoc_sf_axi",
+				      "qmip_pcie_ahb";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnects = <&pcie_noc MASTER_PCIE_1 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_PCIE_1 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "pcie-mem", "cpu-pcie";
+
+			iommu-map = <0x0   &apps_smmu 0x1e00 0x1>,
+				    <0x100 &apps_smmu 0x1e01 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>,
+				<&gcc GCC_PCIE_1_LINK_DOWN_BCR>;
+			reset-names = "pci", "link_down";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+
+			pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
+		};
+
+		pcie1_phy: phy@1c0e000 {
+			compatible = "qcom,sar2130p-qmp-gen3x2-pcie-phy";
+			reg = <0x0 0x01c0e000 0x0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_1_CLKREF_EN>,
+				 <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_1_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie1_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x20000>;
+
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: clock-controller@1fc0000 {
+			compatible = "qcom,sar2130p-tcsr", "syscon";
+			reg = <0x0 0x01fc0000 0x0 0x30000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		remoteproc_adsp: remoteproc@3000000 {
+			compatible = "qcom,sar2130p-adsp-pas";
+			reg = <0x0 0x03000000 0x0 0x10000>;
+
+			interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd RPMHPD_LCX>,
+					<&rpmhpd RPMHPD_LMX>;
+			power-domain-names = "lcx", "lmx";
+
+			memory-region = <&adsp_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			remoteproc_adsp_glink: glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <2>;
+
+				gpr {
+					compatible = "qcom,gpr";
+					qcom,glink-channels = "adsp_apps";
+					qcom,domain = <GPR_DOMAIN_ID_ADSP>;
+					qcom,intents = <512 20>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					q6apm: service@1 {
+						compatible = "qcom,q6apm";
+						reg = <GPR_APM_MODULE_IID>;
+						#sound-dai-cells = <0>;
+						qcom,protection-domain = "avs/audio",
+									 "msm/adsp/audio_pd";
+
+						q6apmdai: dais {
+							compatible = "qcom,q6apm-dais";
+							iommus = <&apps_smmu 0x1801 0x0>;
+						};
+
+						q6apmbedai: bedais {
+							compatible = "qcom,q6apm-lpass-dais";
+							#sound-dai-cells = <1>;
+						};
+					};
+
+					q6prm: service@2 {
+						compatible = "qcom,q6prm";
+						reg = <GPR_PRM_MODULE_IID>;
+						qcom,protection-domain = "avs/audio",
+									 "msm/adsp/audio_pd";
+
+						q6prmcc: clock-controller {
+							compatible = "qcom,q6prm-lpass-clocks";
+							#clock-cells = <2>;
+						};
+					};
+				};
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "adsp";
+					qcom,non-secure-domain;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x1803 0x0>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x1804 0x0>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x1805 0x0>;
+					};
+
+					compute-cb@6 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <6>;
+						iommus = <&apps_smmu 0x1806 0x0>;
+					};
+				};
+			};
+		};
+
+		gpu: gpu@3d00000 {
+			compatible = "qcom,adreno-621.0", "qcom,adreno";
+			reg = <0x0 0x03d00000 0x0 0x40000>,
+			      <0x0 0x03d9e000 0x0 0x2000>,
+			      <0x0 0x03d61000 0x0 0x800>;
+			reg-names = "kgsl_3d0_reg_memory",
+				    "cx_mem",
+				    "cx_dbgc";
+
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+
+			iommus = <&adreno_smmu 0 0x401>;
+
+			operating-points-v2 = <&gpu_opp_table>;
+
+			qcom,gmu = <&gmu>;
+
+			nvmem-cells = <&gpu_speed_bin>;
+			nvmem-cell-names = "speed_bin";
+			#cooling-cells = <2>;
+
+			status = "disabled";
+
+			gpu_zap_shader: zap-shader {
+				memory-region = <&gpu_micro_code_mem>;
+			};
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-843000000 {
+					opp-hz = /bits/ 64 <843000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					opp-supported-hw = <0x1>;
+				};
+
+				opp-780000000 {
+					opp-hz = /bits/ 64 <780000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					opp-supported-hw = <0x1>;
+				};
+
+				opp-644000000 {
+					opp-hz = /bits/ 64 <644000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					opp-supported-hw = <0x3>;
+				};
+
+				opp-570000000 {
+					opp-hz = /bits/ 64 <570000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					opp-supported-hw = <0x3>;
+				};
+
+				opp-450000000 {
+					opp-hz = /bits/ 64 <450000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					opp-supported-hw = <0x3>;
+				};
+
+				opp-320000000 {
+					opp-hz = /bits/ 64 <320000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					opp-supported-hw = <0x3>;
+				};
+
+				opp-235000000 {
+					opp-hz = /bits/ 64 <235000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
+					opp-supported-hw = <0x3>;
+				};
+			};
+		};
+
+		gmu: gmu@3d6a000 {
+			compatible = "qcom,adreno-gmu-621.0", "qcom,adreno-gmu";
+			reg = <0x0 0x03d6a000 0x0 0x35000>,
+			      <0x0 0x03de0000 0x0 0x10000>,
+			      <0x0 0x0b290000 0x0 0x10000>;
+			reg-names = "gmu", "rscc", "gmu_pdc";
+
+			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hfi", "gmu";
+
+			clocks = <&gpucc GPU_CC_AHB_CLK>,
+				 <&gpucc GPU_CC_CX_GMU_CLK>,
+				 <&gpucc GPU_CC_CXO_CLK>,
+				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+				 <&gpucc GPU_CC_HUB_CX_INT_CLK>;
+			clock-names = "ahb",
+				      "gmu",
+				      "cxo",
+				      "axi",
+				      "memnoc",
+				      "hub";
+
+			power-domains = <&gpucc GPU_CX_GDSC>,
+					<&gpucc GPU_GX_GDSC>;
+			power-domain-names = "cx",
+					     "gx";
+
+			iommus = <&adreno_smmu 5 0x400>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			operating-points-v2 = <&gmu_opp_table>;
+
+			gmu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-220000000 {
+					opp-hz = /bits/ 64 <220000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+				};
+
+				opp-550000000 {
+					opp-hz = /bits/ 64 <550000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+				};
+			};
+		};
+
+		gpucc: clock-controller@3d90000 {
+			compatible = "qcom,sar2130p-gpucc";
+			reg = <0x0 0x03d90000 0x0 0xa000>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
+				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
+
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		adreno_smmu: iommu@3da0000 {
+			compatible = "qcom,sar2130p-smmu-500", "qcom,adreno-smmu",
+				     "qcom,smmu-500", "arm,mmu-500";
+			reg = <0x0 0x03da0000 0x0 0x10000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
+				 <&gpucc GPU_CC_AHB_CLK>;
+			clock-names = "hlos",
+				      "bus",
+				      "iface",
+				      "ahb";
+			power-domains = <&gpucc GPU_CX_GDSC>;
+			dma-coherent;
+		};
+
+		usb_1_hsphy: phy@88e3000 {
+			compatible = "qcom,sar2130p-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0x0 0x088e3000 0x0 0x154>;
+			#phy-cells = <0>;
+
+			clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_dp_qmpphy: phy@88e8000 {
+			compatible = "qcom,sar2130p-qmp-usb3-dp-phy";
+			reg = <0x0 0x088e8000 0x0 0x3000>;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
+
+			power-domains = <&gcc USB3_PHY_GDSC>;
+
+			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			orientation-switch;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usb_dp_qmpphy_out: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usb_dp_qmpphy_usb_ss_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_ss>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					usb_dp_qmpphy_dp_in: endpoint {
+					};
+				};
+			};
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sar2130p-dwc3", "qcom,dwc3";
+			reg = <0x0 0x0a6f8800 0x0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&tcsr TCSR_USB3_CLKREF_EN>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+					      <&intc GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "hs_phy_irq",
+					  "dp_hs_phy_irq",
+					  "dm_hs_phy_irq",
+					  "ss_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			interconnects = <&system_noc MASTER_USB3_0 QCOM_ICC_TAG_ALWAYS
+					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+					 &config_noc SLAVE_USB3_0 QCOM_ICC_TAG_ALWAYS>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
+			status = "disabled";
+
+			usb_1_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x0a600000 0x0 0xcd00>;
+				interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x20 0x0>;
+				phys = <&usb_1_hsphy>,
+				       <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy", "usb3-phy";
+
+				snps,has-lpm-erratum;
+				snps,hird-threshold = /bits/ 8 <0x0>;
+				snps,is-utmi-l1-suspend;
+				snps,dis-u1-entry-quirk;
+				snps,dis-u2-entry-quirk;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_u3_susphy_quirk;
+				snps,parkmode-disable-ss-quirk;
+
+				tx-fifo-resize;
+				dma-coherent;
+				usb-role-switch;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_dwc3_ss: endpoint {
+							remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
+						};
+					};
+				};
+			};
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sar2130p-pdc", "qcom,pdc";
+			reg = <0x0 0x0b220000 0x0 0x30000>, <0x0 0x174000f0 0x0 0x64>;
+			qcom,pdc-ranges = <0 480 94>,
+					  <94 609 31>,
+					  <125 63 1>,
+					  <126 716 12>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		aoss_qmp: power-management@c300000 {
+			compatible = "qcom,sar2130p-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0x0 0x0c300000 0x0 0x400>;
+			interrupt-parent = <&ipcc>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+						     IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+		};
+
+		tsens0: thermal-sensor@c263000 {
+			compatible = "qcom,sar2130p-tsens", "qcom,tsens-v2";
+			reg = <0x0 0x0c263000 0x0 0x1000>, /* TM */
+			      <0x0 0x0c222000 0x0 0x1000>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		sram@c3f0000 {
+			compatible = "qcom,rpmh-stats";
+			reg = <0x0 0x0c3f0000 0x0 0x400>;
+		};
+
+		arbiter@c400000 {
+			compatible = "qcom,sar2130p-spmi-pmic-arb",
+				     "qcom,x1e80100-spmi-pmic-arb";
+			reg = <0x0 0x0c400000 0x0 0x3000>,
+			      <0x0 0x0c500000 0x0 0x400000>,
+			      <0x0 0x0c440000 0x0 0x80000>;
+			reg-names = "core", "chnls", "obsrvr";
+
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			spmi_bus: spmi@c42d000 {
+				reg = <0x0 0x0c42d000 0x0 0x4000>,
+				      <0x0 0x0c4c0000 0x0 0x10000>;
+				reg-names = "cnfg", "intr";
+
+				interrupt-names = "periph_irq";
+				interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <4>;
+
+				#address-cells = <2>;
+				#size-cells = <0>;
+			};
+		};
+
+		ipcc: mailbox@ed18000 {
+			compatible = "qcom,sar2130p-ipcc", "qcom,ipcc";
+			reg = <0x0 0x0ed18000 0x0 0x1000>;
+
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			#mbox-cells = <2>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sar2130p-tlmm";
+			reg = <0x0 0x0f100000 0x0 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 156>;
+			wakeup-parent = <&pdc>;
+
+			qup_i2c0_data_clk: qup-i2c0-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio0", "gpio1";
+				function = "qup0";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c1_data_clk: qup-i2c1-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio2", "gpio3";
+				function = "qup1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c2_data_clk: qup-i2c2-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio22", "gpio23";
+				function = "qup2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c3_data_clk: qup-i2c3-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio16", "gpio17";
+				function = "qup3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c4_data_clk: qup-i2c4-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio20", "gpio21";
+				function = "qup4";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c5_data_clk: qup-i2c5-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio95", "gpio96";
+				function = "qup5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c6_data_clk: qup-i2c6-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio91", "gpio92";
+				function = "qup6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c7_data_clk: qup-i2c7-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio8", "gpio9";
+				function = "qup7";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c8_data_clk: qup-i2c8-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio8", "gpio9";
+				function = "qup8";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c9_data_clk: qup-i2c9-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio109", "gpio110";
+				function = "qup9";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c10_data_clk: qup-i2c10-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio4", "gpio5";
+				function = "qup10";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c11_data_clk: qup-i2c11-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio28", "gpio30";
+				function = "qup11";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_spi0_cs0: qup-spi0-cs0-state {
+				pins = "gpio3";
+				function = "qup0";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi0_cs1: qup-spi0-cs1-state {
+				pins = "gpio93";
+				function = "qup0";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup0";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi1_cs: qup-spi1-cs-state {
+				pins = "gpio62";
+				function = "qup1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio2", "gpio3", "gpio61";
+				function = "qup1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi2_cs: qup-spi2-cs-state {
+				pins = "gpio13";
+				function = "qup2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi2_data_clk: qup-spi2-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio22", "gpio23", "gpio12";
+				function = "qup2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi3_cs0: qup-spi3-cs0-state {
+				pins = "gpio19";
+				function = "qup3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi3_cs1: qup-spi3-cs1-state {
+				pins = "gpio41";
+				function = "qup3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi3_data_clk: qup-spi3-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi4_cs0: qup-spi4-cs0-state {
+				pins = "gpio23";
+				function = "qup4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi4_cs1: qup-spi4-cs1-state {
+				pins = "gpio94";
+				function = "qup4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi4_data_clk: qup-spi4-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi5_cs: qup-spi5-cs-state {
+				pins = "gpio98";
+				function = "qup5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi5_data_clk: qup-spi5-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio95", "gpio96", "gpio97";
+				function = "qup5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi6_cs: qup-spi6-cs-state {
+				pins = "gpio63";
+				function = "qup6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi6_data_clk: qup-spi6-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio91", "gpio92", "gpio64";
+				function = "qup6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi7_cs: qup-spi7-cs-state {
+				pins = "gpio27";
+				function = "qup7";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi7_data_clk: qup-spi7-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio24", "gpio25", "gpio26";
+				function = "qup7";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi8_cs: qup-spi8-cs-state {
+				pins = "gpio11";
+				function = "qup8";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi8_data_clk: qup-spi8-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup8";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi9_cs: qup-spi9-cs-state {
+				pins = "gpio35";
+				function = "qup9";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi9_data_clk: qup-spi9-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio109", "gpio110", "gpio34";
+				function = "qup9";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi10_cs: qup-spi10-cs-state {
+				pins = "gpio7";
+				function = "qup10";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi10_data_clk: qup-spi10-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup10";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi11_cs: qup-spi11-cs-state {
+				pins = "gpio15";
+				function = "qup11";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_spi11_data_clk: qup-spi11-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio28", "gpio30", "gpio14";
+				function = "qup11";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_uart7_default: qup-uart7-default-state {
+				cts-pins {
+					pins = "gpio24";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rts-pins {
+					pins = "gpio25";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				rx-pins {
+					pins = "gpio27";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				tx-pins {
+					pins = "gpio26";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			qup_uart11_default: qup-uart11-default-state {
+				pins = "gpio14", "gpio15";
+				function = "qup11";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdc1_default: sdc1-default-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				rclk-pins {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+
+			sdc1_sleep: sdc1-sleep-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				rclk-pins {
+					pins = "sdc1_rclk";
+					bias-pull-down;
+				};
+			};
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sar2130p-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+			reg = <0x0 0x15000000 0x0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>;
+			dma-coherent;
+		};
+
+		intc: interrupt-controller@17200000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			#redistributor-regions = <1>;
+			redistributor-stride = <0x0 0x20000>;
+			reg = <0x0 0x17200000 0x0 0x10000>,
+			      <0x0 0x17260000 0x0 0x100000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			gic_its: msi-controller@17240000 {
+				compatible = "arm,gic-v3-its";
+				reg = <0x0 0x17240000 0x0 0x20000>;
+				msi-controller;
+				#msi-cells = <1>;
+			};
+		};
+
+		apps_rsc: rsc@17a00000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x0 0x17a00000 0x0 0x10000>,
+			      <0x0 0x17a10000 0x0 0x10000>,
+			      <0x0 0x17a20000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS  3>, <SLEEP_TCS   2>,
+					  <WAKE_TCS    2>, <CONTROL_TCS 0>;
+			power-domains = <&cluster_pd>;
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sar2130p-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sar2130p-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs_d1: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
+					};
+
+					rpmhpd_opp_low_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_turbo: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+		};
+
+		cpufreq_hw: cpufreq@17d91000 {
+			compatible = "qcom,sar2130p-cpufreq-epss", "qcom,cpufreq-epss";
+			reg = <0x0 0x17d91000 0x0 0x1000>;
+			reg-names = "freq-domain0";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+			clock-names = "xo", "alternate";
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dcvsh-irq-0";
+			#freq-domain-cells = <1>;
+			#clock-cells = <1>;
+		};
+
+		gem_noc: interconnect@19100000 {
+			compatible = "qcom,sar2130p-gem-noc";
+			reg = <0x0 0x19100000 0x0 0xa2080>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		/*
+		 * Bootloader expects just cache-controller node instead of
+		 * the typical system-cache-controller
+		 */
+		llcc: cache-controller@19200000 {
+			compatible = "qcom,sar2130p-llcc";
+			reg = <0x0 0x19200000 0x0 0x80000>,
+			      <0x0 0x19300000 0x0 0x80000>,
+			      <0x0 0x19a00000 0x0 0x80000>,
+			      <0x0 0x19c00000 0x0 0x80000>,
+			      <0x0 0x19af0000 0x0 0x80000>,
+			      <0x0 0x19cf0000 0x0 0x80000>;
+			reg-names = "llcc0_base",
+				    "llcc1_base",
+				    "llcc_broadcast_base",
+				    "llcc_broadcast_and_base",
+				    "llcc_scratchpad_broadcast_base",
+				    "llcc_scratchpad_broadcast_and_base";
+			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		qfprom: qfprom@221c8000 {
+			compatible = "qcom,sar2130p-qfprom", "qcom,qfprom";
+			reg = <0x0 0x221c8000 0x0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			read-only;
+
+			gpu_speed_bin: gpu-speed-bin@119 {
+				reg = <0x119 0x2>;
+				bits = <5 8>;
+			};
+		};
+
+		nsp_noc: interconnect@320c0000 {
+			compatible = "qcom,sar2130p-nsp-noc";
+			reg = <0x0 0x320c0000 0x0 0x10>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		lpass_ag_noc: interconnect@3c40000 {
+			compatible = "qcom,sar2130p-lpass-ag-noc";
+			reg = <0x0 0x3c40000 0x0 0x10>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	thermal-zones {
+		aoss0-thermal {
+			thermal-sensors = <&tsens0 0>;
+
+			trips {
+				trip-point0 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				aoss0-critical {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+
+			};
+		};
+
+		cpu0-thermal {
+			thermal-sensors = <&tsens0 1>;
+
+			trips {
+				cpu0_alert0: trip-point0 {
+					temperature = <110000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+
+				cpu0_alert1: trip-point1 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				cpu0-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu0_alert0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu0_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu1-thermal {
+			thermal-sensors = <&tsens0 2>;
+
+			trips {
+				cpu1_alert0: trip-point0 {
+					temperature = <110000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+
+				cpu1_alert1: trip-point1 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				cpu1-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu1_alert0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu1_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu2-thermal {
+			thermal-sensors = <&tsens0 3>;
+
+			trips {
+				cpu2_alert0: trip-point0 {
+					temperature = <110000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+
+				cpu2_alert1: trip-point1 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				cpu2-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu2_alert0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu2_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu3-thermal {
+			thermal-sensors = <&tsens0 4>;
+
+			trips {
+				cpu3_alert0: trip-point0 {
+					temperature = <110000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+
+				cpu3_alert1: rip-point1 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				cpu3-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu3_alert0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu3_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		gpuss0-thermal {
+			polling-delay-passive = <250>;
+
+			thermal-sensors = <&tsens0 5>;
+
+			cooling-maps {
+				map0 {
+					trip = <&gpu0_alert0>;
+					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				gpu0_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				trip-point1 {
+					temperature = <90000>;
+					hysteresis = <1000>;
+					type = "hot";
+				};
+
+				trip-point2 {
+					temperature = <115000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		gpuss1-thermal {
+			polling-delay-passive = <250>;
+
+			thermal-sensors = <&tsens0 6>;
+
+			cooling-maps {
+				map0 {
+					trip = <&gpu1_alert0>;
+					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				gpu1_alert0: trip-point0 {
+					temperature = <85000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				trip-point1 {
+					temperature = <90000>;
+					hysteresis = <1000>;
+					type = "hot";
+				};
+
+				trip-point2 {
+					temperature = <115000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		nspss0-thermal {
+			thermal-sensors = <&tsens0 7>;
+
+			trips {
+				trip-point0 {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				trip-point1 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				nspss1-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		nspss1-thermal {
+			thermal-sensors = <&tsens0 8>;
+
+			trips {
+				trip-point0 {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				trip-point1 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				nspss2-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		nspss2-thermal {
+			thermal-sensors = <&tsens0 9>;
+
+			trips {
+				trip-point0 {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				trip-point1 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				nspss2-critical {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		video-thermal {
+			thermal-sensors = <&tsens0 10>;
+
+			trips {
+				trip-point0 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				video-critical {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		ddr-thermal {
+			thermal-sensors = <&tsens0 11>;
+
+			trips {
+				trip-point0 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				ddr-critical {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		camera0-thermal {
+			thermal-sensors = <&tsens0 12>;
+
+			trips {
+				trip-point0 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				camera0-critical {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		camera1-thermal {
+			thermal-sensors = <&tsens0 13>;
+
+			trips {
+				trip-point0 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				camera1-critical {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		mdmss-thermal {
+			thermal-sensors = <&tsens0 14>;
+
+			trips {
+				trip-point0 {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+
+				mdmss-critical {
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};