Message ID | 20241108200440.7562-7-bavishimithil@gmail.com |
---|---|
State | New |
Headers | show |
Series | Initial support for Samsung Galaxy Tab 2 series | expand |
Am Fri, 8 Nov 2024 20:04:35 +0000 schrieb Mithil Bavishi <bavishimithil@gmail.com>: > Create common device tree for Samsung Espresso series devices > > Let's create a common tree for all the variants first. Later we can > device specific trees based on their screen sizes. > > Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com> > --- > .../omap/omap4-samsung-espresso-common.dtsi | 680 ++++++++++++++++++ > 1 file changed, 680 insertions(+) > create mode 100644 arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi > > diff --git a/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi > new file mode 100644 > index 000000000..62ff3f36c > --- /dev/null > +++ b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi > @@ -0,0 +1,680 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/dts-v1/; > +#include "dt-bindings/gpio/gpio.h" > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/input/input.h> > +#include "omap443x.dtsi" > + > +/ { > + memory@80000000 { > + device_type = "memory"; > + reg = <0x80000000 0x40000000>; /* 1 GB */ > + }; > + > + reserved-memory { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + ramoops_region@A0000000 { s/_/-/ in node names please. > + no-map; > + reg = <0xA0000000 0x200000>; If used for ramoops, then there should be a compatible = "ramoops" see Documentation/devicetree/bindings/reserved-memory/ramoops.yaml > + }; > + > + continuous_splash: framebuffer@bef00000{ > + reg = <0xbef00000 (1024 * 600 * 4)>; > + no-map; > + }; > + }; > + > + chosen { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; hmm, no bus here, so no need for address/size-cells, rather specify stdout-path, etc. > + }; > + > + i2c-gpio-5 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpio4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpio4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <10>; > + #address-cells = <1>; > + #size-cells = <0>; hmm, no pinmux here? > + }; > + > + i2c-gpio-6 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpio3 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpio3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <10>; > + #address-cells = <1>; > + #size-cells = <0>; same here > + }; > + > + i2c-gpio-7 { > + compatible = "i2c-gpio"; > + sda-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + scl-gpios = <&gpio2 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; > + i2c-gpio,delay-us = <3>; > + #address-cells = <1>; > + #size-cells = <0>; > + same here > + fuel-gauge@36 { > + compatible = "maxim,max17042"; > + reg = <0x36>; > + pinctrl-0 = <&fuel_alert_irq>; > + pinctrl-names = "default"; > + interrupt-parent = <&gpio2>; > + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; > + maxim,rsns-microohm = <10000>; > + maxim,over-heat-temp = <500>; > + maxim,dead-volt = <2500>; > + maxim,over-volt = <4300>; > + }; > + }; > + > + reg_espresso_wlan: regulator-espresso-wlan { > + pinctrl-names = "default"; > + pinctrl-0 = <&wlanen_gpio>; > + compatible = "regulator-fixed"; > + regulator-name = "espresso_wlan"; > + regulator-max-microvolt = <2000000>; > + regulator-min-microvolt = <2000000>; > + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO_104 */ > + startup-delay-us = <70000>; > + regulator-always-on; > + enable-active-high; > + }; > + > + wlan_pwrseq: wlan-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + clocks = <&twl 0>; > + clock-names = "ext_clock"; > + }; > + > + reg_espresso_internal: regulator-espresso-internal { > + compatible = "regulator-fixed"; > + regulator-name = "eMMC_LDO"; > + regulator-max-microvolt = <1800000>; > + regulator-min-microvolt = <1800000>; > + gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; /* GPIO_63 */ > + startup-delay-us = <100000>; > + regulator-boot-on; > + regulator-always-on; > + enable-active-high; > + }; > + > + reg_espresso_external: regulator-espresso-external { > + compatible = "regulator-fixed"; > + regulator-name = "vmmc1"; > + regulator-max-microvolt = <2800000>; > + regulator-min-microvolt = <2800000>; > + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; /* GPIO_34 */ > + regulator-always-on; hmm, we cannot turn sd card power off? > + enable-active-high; > + }; > + > + reg_touch_ldo_en: regulator-touch-ldo-en { > + compatible = "regulator-fixed"; > + regulator-name = "touch_ldo_en"; > + regulator-max-microvolt = <2800000>; > + regulator-min-microvolt = <2800000>; > + gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* GPIO_54 */ > + regulator-always-on; > + enable-active-high; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + pinctrl-names = "default"; > + pinctrl-0 = <&gpio_keys>; > + > + power { button or key-power > + label = "power"; > + > + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; /* GPIO_wk3 */ > + linux,code = <KEY_POWER>; > + wakeup-source; > + }; > + > + button-volup { > + linux,code = <KEY_VOLUMEUP>; > + label = "volume_up"; /* GPIO_wk30 */ > + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; > + }; > + > + button-voldown { > + linux,code = <KEY_VOLUMEDOWN>; > + label = "volume_down"; /* GPIO_wk8 */ > + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + reg_lcd: regulator-lcd { > + compatible = "regulator-fixed"; > + regulator-name = "lcd_en"; > + gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; /* GPIO_135 */ > + regulator-max-microvolt = <3300000>; > + regulator-min-microvolt = <3300000>; > + enable-active-high; > + regulator-boot-on; > + }; > + > + pwm10: pwm-10 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pwm10_default>; > + compatible = "ti,omap-dmtimer-pwm"; > + #pwm-cells = <3>; > + ti,timers = <&timer10>; > + ti,clock-source = <0x00>; > + }; > + > + lvds-encoder { > + compatible = "doestek,dtc34lm85am", "lvds-encoder"; > + powerdown-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; /* GPIO_136 */ > + power-supply = <®_lcd>; > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + bridge_in: endpoint { > + remote-endpoint = <&dpi_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + bridge_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > + }; > + > + vibrator { > + compatible = "gpio-vibrator"; > + enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; /* GPIO_38 */ > + pinctrl-names = "default"; > + pinctrl-0 = <&vibrator_default>; > + }; > + > + gp2a_shunt: current-sense-shunt { > + compatible = "current-sense-shunt"; > + io-channels = <&gpadc 4>; > + shunt-resistor-micro-ohms = <24000000>; /* 24 ohms */ > + #io-channel-cells = <0>; > + }; > + > + led-ir { > + compatible = "gpio-ir-tx"; > + gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* GPIO_59 */ pinmux? > + }; > +}; > + > +&omap4_pmx_wkup { order node names alphabetically > + twl6030_wkup_pins: pinmux-twl6030-wkup-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x54, PIN_OUTPUT | MUX_MODE3) > + /* fref_clk0_out.sys_drm_msecure */ > + >; > + }; > + This can come from twl6030_omap4.dtsi > + gpio_keys: gpio-keys-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x046, WAKEUP_EN | PIN_INPUT | MUX_MODE3) > + /* sim_cd.gpio_wk3 - EXT_WAKEUP */ > + OMAP4_IOPAD(0x056, WAKEUP_EN | PIN_INPUT | MUX_MODE3) > + /* fref_clk3_req.gpio_wk30 - VOL_UP */ > + OMAP4_IOPAD(0x05C, WAKEUP_EN | PIN_INPUT | MUX_MODE3) > + /* fref_clk4_out.gpio_wk8 - VOL_DN */ > + >; > + }; > + > + prox_irq: prox-irq-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x042, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE3) > + /* sim_clk.gpio_wk1 - PS_VOUT */ > + >; > + }; > +}; > + > +&omap4_pmx_core { order node names alphabetically > + pwm10_default: pinmux-pwm10-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0X0D6, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE1) > + /* usbb1_ulpitll_dat6.dmtimer10_pwm_evt - LED_BACKLIGHT_PWM */ > + >; > + }; > + > + backlight_pins: pinmux-backlight-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0X0D8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) > + /* usbb1_ulpitll_dat7.gpio_95 - LED_BACKLIGHT_RESET */ > + >; > + }; > + > + lvds_pins: pinmux-lvds-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0X136, PIN_OUTPUT | MUX_MODE3) > + /* mcspi1_simo.gpio_136 - LVDS_nSHDN */ > + >; > + }; > + > + i2c1_pins: pinmux-i2c1-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ > + OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ > + >; > + }; > + > + i2c2_pins: pinmux-i2c2-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ > + OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ > + >; > + }; > + > + i2c3_pins: pinmux-i2c3-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ > + OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ > + >; > + }; > + > + i2c4_pins: pinmux-i2c4-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ > + OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ > + >; > + }; > + > + mmc2_pins: pinmux-mmc2-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x040, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat0 */ > + OMAP4_IOPAD(0x042, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat1 */ > + OMAP4_IOPAD(0x044, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat2 */ > + OMAP4_IOPAD(0x046, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat3 */ > + OMAP4_IOPAD(0x048, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat4 */ > + OMAP4_IOPAD(0x04a, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat5 */ > + OMAP4_IOPAD(0x04c, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat6 */ > + OMAP4_IOPAD(0x04e, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat7 */ > + OMAP4_IOPAD(0x082, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_clk */ > + OMAP4_IOPAD(0x084, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_cmd */ > + >; > + }; > + > + mmc1_pins: pinmux-mmc1-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* sdmmc1_clk */ > + OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc1_cmd */ > + OMAP4_IOPAD(0x0e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc1_dat0 */ > + OMAP4_IOPAD(0x0e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ > + OMAP4_IOPAD(0x0ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ > + OMAP4_IOPAD(0x0ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ > + >; > + }; > + > + mmc5_pins: pinmux-mmc5-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x148, PIN_INPUT_PULLDOWN | MUX_MODE0) > + /* sdmmc5_clk.sdmmc5_clk */ > + OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) > + /* sdmmc5_cmd.sdmmc5_cmd */ > + OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) > + /* sdmmc5_dat0.sdmmc5_dat0 */ > + OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) > + /* sdmmc5_dat1.sdmmc5_dat1 */ > + OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) > + /* sdmmc5_dat2.sdmmc5_dat2 */ > + OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) > + /* sdmmc5_dat3.sdmmc5_dat3 */ > + >; > + }; > + > + dss_dpi_pins: pinmux-dss-dpi-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x162, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data23 */ > + OMAP4_IOPAD(0x164, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data22 */ > + OMAP4_IOPAD(0x166, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data21 */ > + OMAP4_IOPAD(0x168, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data20 */ > + OMAP4_IOPAD(0x16a, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data19 */ > + OMAP4_IOPAD(0x16c, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data18 */ > + OMAP4_IOPAD(0x16e, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data15 */ > + OMAP4_IOPAD(0x170, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data14 */ > + OMAP4_IOPAD(0x172, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data13 */ > + OMAP4_IOPAD(0x174, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data12 */ > + OMAP4_IOPAD(0x176, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data11 */ > + > + OMAP4_IOPAD(0x1b4, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data10 */ > + OMAP4_IOPAD(0x1b6, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data9 */ > + OMAP4_IOPAD(0x1b8, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data16 */ > + OMAP4_IOPAD(0x1ba, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data17 */ > + OMAP4_IOPAD(0x1bc, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_hsync */ > + OMAP4_IOPAD(0x1be, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_pclk */ > + OMAP4_IOPAD(0x1c0, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_vsync */ > + OMAP4_IOPAD(0x1c2, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_de */ > + OMAP4_IOPAD(0x1c4, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data8 */ > + OMAP4_IOPAD(0x1c6, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data7 */ > + OMAP4_IOPAD(0x1c8, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data6 */ > + OMAP4_IOPAD(0x1ca, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data5 */ > + OMAP4_IOPAD(0x1cc, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data4 */ > + OMAP4_IOPAD(0x1ce, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data3 */ > + > + OMAP4_IOPAD(0x1d0, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data2 */ > + OMAP4_IOPAD(0x1d2, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data1 */ > + OMAP4_IOPAD(0x1d4, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data0 */ > + >; > + }; > + > + wlanen_gpio: pinmux-wlanen-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3) /* gpmc_ncs7.gpio_104 */ > + >; > + }; > + > + twl6030_pins: pinmux-twl6030-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x19e, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) > + /* sys_nirq1.sys_nirq1 */ > + >; > + }; you can simply include twl6030_omap4.dtsi describing recommended connection between omap4 SoCs and twl603X pmics. > + > + fuel_alert_irq: pinmux-fuel-alert-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x068, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE3) > + /* gpmc_a20.gpio_44 */ > + >; > + }; > + > + uart3_pins: pinmux-uart3-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx */ > + OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx */ > + >; > + }; > + > + uart2_pins: pinmux-uart2-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) > + /* uart2_cts.uart2_cts */ > + OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE0) > + /* uart2_rts.uart2_rts */ > + OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) > + /* uart2_rx.uart2_rx */ > + OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE0) > + /* uart2_tx.uart2_tx */ > + >; > + }; > + > + wlan_host_wake: pinmux-wlan-host-wake-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x0bc, WAKEUP_EN | PIN_INPUT | MUX_MODE3) > + /* cam_shutter.gpio_81 - WLAN_HOST_WAKE */ It might be an idea to use a dedicated wakeup irq instead of explicitely specifying WAKEUP_EN like you did for the uart. That counts for other occurances of WAKEUP_EN as well. > + >; > + }; > + > + bluetooth_pins: pinmux-bluetooth-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3) > + /* gpmc_ncs6.gpio_103 - BT_EN */ > + OMAP4_IOPAD(0x0be, PIN_OUTPUT | MUX_MODE3) > + /* cam_strobe.gpio_82 - BT_nRST */ > + OMAP4_IOPAD(0x0c0, WAKEUP_EN | PIN_INPUT | MUX_MODE3) > + /* cam_globalreset.gpio_83 - BT_HOST_WAKE */ > + OMAP4_IOPAD(0x0d4, PIN_OUTPUT | MUX_MODE3) > + /* usbb1_ulpitll_dat5.gpio_93 - BT_WAKE */ > + >; > + }; > + > + touch_pins: pinmux-touch-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x06c, PIN_INPUT | MUX_MODE3) > + /* gpmc_a22.gpio_46 - TSP_INT */ > + >; > + }; > + > + vibrator_default: pinmux-vibrator-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x05c, PIN_INPUT_PULLDOWN | MUX_MODE3) > + /* gpmc_ad14.gpio_38 - MOTOR_EN */ > + >; > + }; > + > + gp2a_irq: pinmux-gp2a-irq-pins { > + pinctrl-single,pins = < > + OMAP4_IOPAD(0x052, WAKEUP_EN | PIN_INPUT | MUX_MODE3) > + /* gpmc_ad9.gpio_33 - ALS_INT_18 */ > + >; > + }; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart3_pins>; > + > + interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH > + &omap4_pmx_core OMAP4_UART3_RX>; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; > + > + clock-frequency = <400000>; > + > + twl: twl@48 { generic node names: pmic@48 yes, there are a lot of bad examples in the tree people (including me!) keep copying from, but lets not create new bad examples. > + reg = <0x48>; > + #clock-cells = <1>; > + > + pinctrl-names = "default"; > + pinctrl-0 = < > + &twl6030_pins > + &twl6030_wkup_pins > + >; > + > + /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ > + interrupt-parent = <&gic>; > + system-power-controller; > + }; > +}; > + > +#include "twl6032.dtsi" > + > +&ldo1 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > +}; > + > +&ldo3 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > +}; > + > +&ldo4 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-always-on; > +}; > + > +&ldo5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > +}; > + > +&ldo6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-state-mem { > + regulator-off-in-suspend; > + }; > +}; > + > +&smps4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > +}; > + > +&ldousb { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > +}; > + > +&i2c2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c2_pins>; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c3_pins>; > +}; > + > +&i2c4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c4_pins>; > + > + accelerometer@18 { > + compatible = "bosch,bma254"; > + reg = <0x18>; > + vdd-supply = <&ldo4>; > + vddio-supply = <&ldo5>; > + interrupt-parent = <&gpio4>; > + interrupts = <25 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>, > + <26 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; this looks odd, binding says IRQ_TYPE_EDGE_RISING. Why do you think you need both? After something is rising, it is high, so both seem not to make sense. > + mount-matrix = "-1", "0", "0", > + "0", "1", "0", > + "0", "0", "1"; hmm, checking twice, since I mixed up something earlier. This just inverts x values, so we are mirroring across y-z plane, that does not look like a rotation matrix, so it does not describe how it is mounted. Eg. the n900 has two -1 in there, that is a turn by 180 degree. Your mount-matrix would be achieved, by cutting the chip into ultra thin slices, sorting them upside down and glueing that together. I doubt somebody does that. Regards, Andreas
diff --git a/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi new file mode 100644 index 000000000..62ff3f36c --- /dev/null +++ b/arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi @@ -0,0 +1,680 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/dts-v1/; +#include "dt-bindings/gpio/gpio.h" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> +#include "omap443x.dtsi" + +/ { + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1 GB */ + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ramoops_region@A0000000 { + no-map; + reg = <0xA0000000 0x200000>; + }; + + continuous_splash: framebuffer@bef00000{ + reg = <0xbef00000 (1024 * 600 * 4)>; + no-map; + }; + }; + + chosen { + #address-cells = <1>; + #size-cells = <1>; + ranges; + }; + + i2c-gpio-5 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <10>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c-gpio-6 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio3 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <10>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c-gpio-7 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio2 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <3>; + #address-cells = <1>; + #size-cells = <0>; + + fuel-gauge@36 { + compatible = "maxim,max17042"; + reg = <0x36>; + pinctrl-0 = <&fuel_alert_irq>; + pinctrl-names = "default"; + interrupt-parent = <&gpio2>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; + maxim,rsns-microohm = <10000>; + maxim,over-heat-temp = <500>; + maxim,dead-volt = <2500>; + maxim,over-volt = <4300>; + }; + }; + + reg_espresso_wlan: regulator-espresso-wlan { + pinctrl-names = "default"; + pinctrl-0 = <&wlanen_gpio>; + compatible = "regulator-fixed"; + regulator-name = "espresso_wlan"; + regulator-max-microvolt = <2000000>; + regulator-min-microvolt = <2000000>; + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO_104 */ + startup-delay-us = <70000>; + regulator-always-on; + enable-active-high; + }; + + wlan_pwrseq: wlan-pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&twl 0>; + clock-names = "ext_clock"; + }; + + reg_espresso_internal: regulator-espresso-internal { + compatible = "regulator-fixed"; + regulator-name = "eMMC_LDO"; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; /* GPIO_63 */ + startup-delay-us = <100000>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + }; + + reg_espresso_external: regulator-espresso-external { + compatible = "regulator-fixed"; + regulator-name = "vmmc1"; + regulator-max-microvolt = <2800000>; + regulator-min-microvolt = <2800000>; + gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; /* GPIO_34 */ + regulator-always-on; + enable-active-high; + }; + + reg_touch_ldo_en: regulator-touch-ldo-en { + compatible = "regulator-fixed"; + regulator-name = "touch_ldo_en"; + regulator-max-microvolt = <2800000>; + regulator-min-microvolt = <2800000>; + gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* GPIO_54 */ + regulator-always-on; + enable-active-high; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys>; + + power { + label = "power"; + + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; /* GPIO_wk3 */ + linux,code = <KEY_POWER>; + wakeup-source; + }; + + button-volup { + linux,code = <KEY_VOLUMEUP>; + label = "volume_up"; /* GPIO_wk30 */ + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + }; + + button-voldown { + linux,code = <KEY_VOLUMEDOWN>; + label = "volume_down"; /* GPIO_wk8 */ + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + }; + + reg_lcd: regulator-lcd { + compatible = "regulator-fixed"; + regulator-name = "lcd_en"; + gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; /* GPIO_135 */ + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + enable-active-high; + regulator-boot-on; + }; + + pwm10: pwm-10 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm10_default>; + compatible = "ti,omap-dmtimer-pwm"; + #pwm-cells = <3>; + ti,timers = <&timer10>; + ti,clock-source = <0x00>; + }; + + lvds-encoder { + compatible = "doestek,dtc34lm85am", "lvds-encoder"; + powerdown-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; /* GPIO_136 */ + power-supply = <®_lcd>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + bridge_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; + + vibrator { + compatible = "gpio-vibrator"; + enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; /* GPIO_38 */ + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_default>; + }; + + gp2a_shunt: current-sense-shunt { + compatible = "current-sense-shunt"; + io-channels = <&gpadc 4>; + shunt-resistor-micro-ohms = <24000000>; /* 24 ohms */ + #io-channel-cells = <0>; + }; + + led-ir { + compatible = "gpio-ir-tx"; + gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* GPIO_59 */ + }; +}; + +&omap4_pmx_wkup { + twl6030_wkup_pins: pinmux-twl6030-wkup-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x54, PIN_OUTPUT | MUX_MODE3) + /* fref_clk0_out.sys_drm_msecure */ + >; + }; + + gpio_keys: gpio-keys-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x046, WAKEUP_EN | PIN_INPUT | MUX_MODE3) + /* sim_cd.gpio_wk3 - EXT_WAKEUP */ + OMAP4_IOPAD(0x056, WAKEUP_EN | PIN_INPUT | MUX_MODE3) + /* fref_clk3_req.gpio_wk30 - VOL_UP */ + OMAP4_IOPAD(0x05C, WAKEUP_EN | PIN_INPUT | MUX_MODE3) + /* fref_clk4_out.gpio_wk8 - VOL_DN */ + >; + }; + + prox_irq: prox-irq-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x042, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE3) + /* sim_clk.gpio_wk1 - PS_VOUT */ + >; + }; +}; + +&omap4_pmx_core { + pwm10_default: pinmux-pwm10-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0X0D6, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE1) + /* usbb1_ulpitll_dat6.dmtimer10_pwm_evt - LED_BACKLIGHT_PWM */ + >; + }; + + backlight_pins: pinmux-backlight-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0X0D8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) + /* usbb1_ulpitll_dat7.gpio_95 - LED_BACKLIGHT_RESET */ + >; + }; + + lvds_pins: pinmux-lvds-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0X136, PIN_OUTPUT | MUX_MODE3) + /* mcspi1_simo.gpio_136 - LVDS_nSHDN */ + >; + }; + + i2c1_pins: pinmux-i2c1-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + i2c2_pins: pinmux-i2c2-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ + >; + }; + + i2c3_pins: pinmux-i2c3-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ + >; + }; + + i2c4_pins: pinmux-i2c4-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ + OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ + >; + }; + + mmc2_pins: pinmux-mmc2-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x040, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat0 */ + OMAP4_IOPAD(0x042, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat1 */ + OMAP4_IOPAD(0x044, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat2 */ + OMAP4_IOPAD(0x046, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat3 */ + OMAP4_IOPAD(0x048, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat4 */ + OMAP4_IOPAD(0x04a, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat5 */ + OMAP4_IOPAD(0x04c, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat6 */ + OMAP4_IOPAD(0x04e, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat7 */ + OMAP4_IOPAD(0x082, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_clk */ + OMAP4_IOPAD(0x084, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_cmd */ + >; + }; + + mmc1_pins: pinmux-mmc1-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x0e2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* sdmmc1_clk */ + OMAP4_IOPAD(0x0e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc1_cmd */ + OMAP4_IOPAD(0x0e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc1_dat0 */ + OMAP4_IOPAD(0x0e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ + OMAP4_IOPAD(0x0ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ + OMAP4_IOPAD(0x0ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ + >; + }; + + mmc5_pins: pinmux-mmc5-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x148, PIN_INPUT_PULLDOWN | MUX_MODE0) + /* sdmmc5_clk.sdmmc5_clk */ + OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) + /* sdmmc5_cmd.sdmmc5_cmd */ + OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) + /* sdmmc5_dat0.sdmmc5_dat0 */ + OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) + /* sdmmc5_dat1.sdmmc5_dat1 */ + OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) + /* sdmmc5_dat2.sdmmc5_dat2 */ + OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) + /* sdmmc5_dat3.sdmmc5_dat3 */ + >; + }; + + dss_dpi_pins: pinmux-dss-dpi-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x162, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data23 */ + OMAP4_IOPAD(0x164, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data22 */ + OMAP4_IOPAD(0x166, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data21 */ + OMAP4_IOPAD(0x168, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data20 */ + OMAP4_IOPAD(0x16a, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data19 */ + OMAP4_IOPAD(0x16c, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data18 */ + OMAP4_IOPAD(0x16e, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data15 */ + OMAP4_IOPAD(0x170, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data14 */ + OMAP4_IOPAD(0x172, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data13 */ + OMAP4_IOPAD(0x174, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data12 */ + OMAP4_IOPAD(0x176, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data11 */ + + OMAP4_IOPAD(0x1b4, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data10 */ + OMAP4_IOPAD(0x1b6, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data9 */ + OMAP4_IOPAD(0x1b8, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data16 */ + OMAP4_IOPAD(0x1ba, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data17 */ + OMAP4_IOPAD(0x1bc, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_hsync */ + OMAP4_IOPAD(0x1be, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_pclk */ + OMAP4_IOPAD(0x1c0, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_vsync */ + OMAP4_IOPAD(0x1c2, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_de */ + OMAP4_IOPAD(0x1c4, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data8 */ + OMAP4_IOPAD(0x1c6, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data7 */ + OMAP4_IOPAD(0x1c8, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data6 */ + OMAP4_IOPAD(0x1ca, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data5 */ + OMAP4_IOPAD(0x1cc, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data4 */ + OMAP4_IOPAD(0x1ce, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data3 */ + + OMAP4_IOPAD(0x1d0, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data2 */ + OMAP4_IOPAD(0x1d2, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data1 */ + OMAP4_IOPAD(0x1d4, PIN_OFF_OUTPUT_LOW | MUX_MODE5) /* dispc2_data0 */ + >; + }; + + wlanen_gpio: pinmux-wlanen-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3) /* gpmc_ncs7.gpio_104 */ + >; + }; + + twl6030_pins: pinmux-twl6030-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x19e, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) + /* sys_nirq1.sys_nirq1 */ + >; + }; + + fuel_alert_irq: pinmux-fuel-alert-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x068, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE3) + /* gpmc_a20.gpio_44 */ + >; + }; + + uart3_pins: pinmux-uart3-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x144, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx */ + OMAP4_IOPAD(0x146, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx */ + >; + }; + + uart2_pins: pinmux-uart2-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0) + /* uart2_cts.uart2_cts */ + OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE0) + /* uart2_rts.uart2_rts */ + OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0) + /* uart2_rx.uart2_rx */ + OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE0) + /* uart2_tx.uart2_tx */ + >; + }; + + wlan_host_wake: pinmux-wlan-host-wake-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x0bc, WAKEUP_EN | PIN_INPUT | MUX_MODE3) + /* cam_shutter.gpio_81 - WLAN_HOST_WAKE */ + >; + }; + + bluetooth_pins: pinmux-bluetooth-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3) + /* gpmc_ncs6.gpio_103 - BT_EN */ + OMAP4_IOPAD(0x0be, PIN_OUTPUT | MUX_MODE3) + /* cam_strobe.gpio_82 - BT_nRST */ + OMAP4_IOPAD(0x0c0, WAKEUP_EN | PIN_INPUT | MUX_MODE3) + /* cam_globalreset.gpio_83 - BT_HOST_WAKE */ + OMAP4_IOPAD(0x0d4, PIN_OUTPUT | MUX_MODE3) + /* usbb1_ulpitll_dat5.gpio_93 - BT_WAKE */ + >; + }; + + touch_pins: pinmux-touch-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x06c, PIN_INPUT | MUX_MODE3) + /* gpmc_a22.gpio_46 - TSP_INT */ + >; + }; + + vibrator_default: pinmux-vibrator-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x05c, PIN_INPUT_PULLDOWN | MUX_MODE3) + /* gpmc_ad14.gpio_38 - MOTOR_EN */ + >; + }; + + gp2a_irq: pinmux-gp2a-irq-pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x052, WAKEUP_EN | PIN_INPUT | MUX_MODE3) + /* gpmc_ad9.gpio_33 - ALS_INT_18 */ + >; + }; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + + interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH + &omap4_pmx_core OMAP4_UART3_RX>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + #clock-cells = <1>; + + pinctrl-names = "default"; + pinctrl-0 = < + &twl6030_pins + &twl6030_wkup_pins + >; + + /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-parent = <&gic>; + system-power-controller; + }; +}; + +#include "twl6032.dtsi" + +&ldo1 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; +}; + +&ldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; +}; + +&ldo4 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; +}; + +&ldo5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; +}; + +&smps4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +}; + +&ldousb { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + accelerometer@18 { + compatible = "bosch,bma254"; + reg = <0x18>; + vdd-supply = <&ldo4>; + vddio-supply = <&ldo5>; + interrupt-parent = <&gpio4>; + interrupts = <25 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>, + <26 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + mount-matrix = "-1", "0", "0", + "0", "1", "0", + "0", "0", "1"; + }; + + magnetometer@2e { + compatible = "yamaha,yas530"; + reg = <0x2e>; + vdd-supply = <&ldo4>; + iovdd-supply = <&ldo5>; + reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; + interrupts = <&gpio6 10 IRQ_TYPE_EDGE_RISING>; + }; + + light-sensor@44 { + compatible = "sharp,gp2ap002a00f"; + reg = <0x44>; + interrupt-parent = <&gpio1>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&ldo4>; + vio-supply = <&ldo4>; + io-channels = <&gp2a_shunt>; + io-channel-names = "alsout"; + sharp,proximity-far-hysteresis = /bits/ 8 <0x40>; + sharp,proximity-close-hysteresis = /bits/ 8 <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&gp2a_irq &prox_irq>; + }; +}; + +&dss { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&dss_dpi_pins>; + + port { + dpi_out: endpoint { + remote-endpoint = <&bridge_in>; + data-lines = <24>; + }; + }; +}; + +&twl_usb_comparator { + usb-supply = <&ldousb>; +}; + +&usb_otg_hs { + interface-type = <1>; + mode = <3>; + power = <50>; +}; + +&mmc1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + + vmmc-supply = <®_espresso_external>; + bus-width = <4>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + + vmmc-supply = <®_espresso_internal>; + ti,non-removable; + bus-width = <8>; +}; + +&mmc3 { + status = "disabled"; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + non-removable; + bus-width = <4>; + vmmc-supply = <®_espresso_wlan>; + mmc-pwrseq = <&wlan_pwrseq>; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc5_pins>; + + brcmf: wifi@1 { + compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac"; + reg = <1>; + + interrupt-parent = <&gpio3>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wake"; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_host_wake>; + }; +}; + +&uart2 { + interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH + &omap4_pmx_core OMAP4_UART2_RX>; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + bluetooth { + compatible = "brcm,bcm4330-bt"; + pinctrl-names = "default"; + pinctrl-0 = <&bluetooth_pins>; + shutdown-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio3 18 GPIO_ACTIVE_LOW>; + device-wakeup-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio3>; + interrupts = <19 IRQ_TYPE_EDGE_FALLING>; + }; +};
Create common device tree for Samsung Espresso series devices Let's create a common tree for all the variants first. Later we can device specific trees based on their screen sizes. Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com> --- .../omap/omap4-samsung-espresso-common.dtsi | 680 ++++++++++++++++++ 1 file changed, 680 insertions(+) create mode 100644 arch/arm/boot/dts/ti/omap/omap4-samsung-espresso-common.dtsi