@@ -955,7 +955,6 @@ static void reset_state(struct scsi_tape *STp)
STp->partition = find_partition(STp);
if (STp->partition < 0)
STp->partition = 0;
- STp->new_partition = STp->partition;
}
}
@@ -2928,14 +2927,17 @@ static int st_int_ioctl(struct scsi_tape *STp, unsigned int cmd_in, unsigned lon
if (cmd_in == MTSETDENSITY) {
(STp->buffer)->b_data[4] = arg;
STp->density_changed = 1; /* At least we tried ;-) */
+ STp->changed_density = arg;
} else if (cmd_in == SET_DENS_AND_BLK)
(STp->buffer)->b_data[4] = arg >> 24;
else
(STp->buffer)->b_data[4] = STp->density;
if (cmd_in == MTSETBLK || cmd_in == SET_DENS_AND_BLK) {
ltmp = arg & MT_ST_BLKSIZE_MASK;
- if (cmd_in == MTSETBLK)
+ if (cmd_in == MTSETBLK) {
STp->blksize_changed = 1; /* At least we tried ;-) */
+ STp->changed_blksize = arg;
+ }
} else
ltmp = STp->block_size;
(STp->buffer)->b_data[9] = (ltmp >> 16);
@@ -3635,6 +3637,22 @@ static long st_ioctl(struct file *file, unsigned int cmd_in, unsigned long arg)
goto out;
}
reset_state(STp); /* Clears pos_unknown */
+
+ /* Fix the device settings after reset, ignore errors */
+ if (mtc.mt_op == MTREW || mtc.mt_op == MTSEEK ||
+ mtc.mt_op == MTEOM) {
+ if (STp->can_partitions) {
+ /* STp->new_partition contains the
+ * latest partition set
+ */
+ STp->partition = 0;
+ switch_partition(STp);
+ }
+ if (STp->density_changed)
+ st_int_ioctl(STp, MTSETDENSITY, STp->changed_density);
+ if (STp->blksize_changed)
+ st_int_ioctl(STp, MTSETBLK, STp->changed_blksize);
+ }
}
if (mtc.mt_op != MTNOP && mtc.mt_op != MTSETBLK &&
@@ -165,12 +165,14 @@ struct scsi_tape {
unsigned char compression_changed;
unsigned char drv_buffer;
unsigned char density;
+ unsigned char changed_density;
unsigned char door_locked;
unsigned char autorew_dev; /* auto-rewind device */
unsigned char rew_at_close; /* rewind necessary at close */
unsigned char inited;
unsigned char cleaning_req; /* cleaning requested? */
int block_size;
+ int changed_blksize;
int min_block;
int max_block;
int recover_count; /* From tape opening */
Some of the allowed operations put the tape into a known position to continue operation, assuming only the tape position has changed. But reset sets partition, density and block size to drive default values. These should be restored to the values before reset. This is only done for the operations not starting a new tape session. Normally the current block size and density are stored by the drive. If the settings have been changed, the changed values have to be saved by the driver across reset. Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> --- drivers/scsi/st.c | 22 ++++++++++++++++++++-- drivers/scsi/st.h | 2 ++ 2 files changed, 22 insertions(+), 2 deletions(-)