@@ -719,7 +719,7 @@ static int hi556_write_reg_list(struct hi556 *hi556,
r_list->regs[i].val);
if (ret) {
dev_err_ratelimited(&client->dev,
- "failed to write reg 0x%4.4x. error = %d",
+ "failed to write reg 0x%4.4x. error = %d\n",
r_list->regs[i].address, ret);
return ret;
}
@@ -926,7 +926,7 @@ static int hi556_identify_module(struct hi556 *hi556)
return ret;
if (val != HI556_CHIP_ID) {
- dev_err(&client->dev, "chip id mismatch: %x!=%x",
+ dev_err(&client->dev, "chip id mismatch: %x!=%x\n",
HI556_CHIP_ID, val);
return -ENXIO;
}
@@ -1002,14 +1002,14 @@ static int hi556_start_streaming(struct hi556 *hi556)
reg_list = &link_freq_configs[link_freq_index].reg_list;
ret = hi556_write_reg_list(hi556, reg_list);
if (ret) {
- dev_err(&client->dev, "failed to set plls");
+ dev_err(&client->dev, "failed to set plls\n");
return ret;
}
reg_list = &hi556->cur_mode->reg_list;
ret = hi556_write_reg_list(hi556, reg_list);
if (ret) {
- dev_err(&client->dev, "failed to set mode");
+ dev_err(&client->dev, "failed to set mode\n");
return ret;
}
@@ -1021,7 +1021,7 @@ static int hi556_start_streaming(struct hi556 *hi556)
HI556_REG_VALUE_16BIT, HI556_MODE_STREAMING);
if (ret) {
- dev_err(&client->dev, "failed to set stream");
+ dev_err(&client->dev, "failed to set stream\n");
return ret;
}
@@ -1034,7 +1034,7 @@ static void hi556_stop_streaming(struct hi556 *hi556)
if (hi556_write_reg(hi556, HI556_REG_MODE_SELECT,
HI556_REG_VALUE_16BIT, HI556_MODE_STANDBY))
- dev_err(&client->dev, "failed to set stream");
+ dev_err(&client->dev, "failed to set stream\n");
}
static int hi556_set_stream(struct v4l2_subdev *sd, int enable)
@@ -1229,25 +1229,25 @@ static int hi556_check_hwcfg(struct device *dev)
ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk);
if (ret) {
- dev_err(dev, "can't get clock frequency");
+ dev_err(dev, "can't get clock frequency\n");
goto check_hwcfg_error;
}
if (mclk != HI556_MCLK) {
- dev_err(dev, "external clock %d is not supported", mclk);
+ dev_err(dev, "external clock %d is not supported\n", mclk);
ret = -EINVAL;
goto check_hwcfg_error;
}
if (bus_cfg.bus.mipi_csi2.num_data_lanes != 2) {
- dev_err(dev, "number of CSI2 data lanes %d is not supported",
+ dev_err(dev, "number of CSI2 data lanes %d is not supported\n",
bus_cfg.bus.mipi_csi2.num_data_lanes);
ret = -EINVAL;
goto check_hwcfg_error;
}
if (!bus_cfg.nr_of_link_frequencies) {
- dev_err(dev, "no link frequencies defined");
+ dev_err(dev, "no link frequencies defined\n");
ret = -EINVAL;
goto check_hwcfg_error;
}
@@ -1260,7 +1260,7 @@ static int hi556_check_hwcfg(struct device *dev)
}
if (j == bus_cfg.nr_of_link_frequencies) {
- dev_err(dev, "no link frequency %lld supported",
+ dev_err(dev, "no link frequency %lld supported\n",
link_freq_menu_items[i]);
ret = -EINVAL;
goto check_hwcfg_error;
@@ -1334,7 +1334,7 @@ static int hi556_probe(struct i2c_client *client)
ret = hi556_check_hwcfg(&client->dev);
if (ret) {
- dev_err(&client->dev, "failed to check HW configuration: %d",
+ dev_err(&client->dev, "failed to check HW configuration: %d\n",
ret);
return ret;
}
@@ -1372,7 +1372,7 @@ static int hi556_probe(struct i2c_client *client)
ret = hi556_identify_module(hi556);
if (ret) {
- dev_err(&client->dev, "failed to find sensor: %d", ret);
+ dev_err(&client->dev, "failed to find sensor: %d\n", ret);
goto probe_error_power_off;
}
}
@@ -1381,7 +1381,7 @@ static int hi556_probe(struct i2c_client *client)
hi556->cur_mode = &supported_modes[0];
ret = hi556_init_controls(hi556);
if (ret) {
- dev_err(&client->dev, "failed to init controls: %d", ret);
+ dev_err(&client->dev, "failed to init controls: %d\n", ret);
goto probe_error_v4l2_ctrl_handler_free;
}
@@ -1392,13 +1392,13 @@ static int hi556_probe(struct i2c_client *client)
hi556->pad.flags = MEDIA_PAD_FL_SOURCE;
ret = media_entity_pads_init(&hi556->sd.entity, 1, &hi556->pad);
if (ret) {
- dev_err(&client->dev, "failed to init entity pads: %d", ret);
+ dev_err(&client->dev, "failed to init entity pads: %d\n", ret);
goto probe_error_v4l2_ctrl_handler_free;
}
ret = v4l2_async_register_subdev_sensor(&hi556->sd);
if (ret < 0) {
- dev_err(&client->dev, "failed to register V4L2 subdev: %d",
+ dev_err(&client->dev, "failed to register V4L2 subdev: %d\n",
ret);
goto probe_error_media_entity_cleanup;
}
Many hi556 dev_err() error messages miss a terminating '\n', add the missing '\n' to these. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- drivers/media/i2c/hi556.c | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-)