@@ -224,7 +224,6 @@ int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm);
u16 asix_read_medium_status(struct usbnet *dev, int in_pm);
int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm);
-void asix_adjust_link(struct net_device *netdev);
int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm);
@@ -414,28 +414,6 @@ int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm)
return ret;
}
-/* set MAC link settings according to information from phylib */
-void asix_adjust_link(struct net_device *netdev)
-{
- struct phy_device *phydev = netdev->phydev;
- struct usbnet *dev = netdev_priv(netdev);
- u16 mode = 0;
-
- if (phydev->link) {
- mode = AX88772_MEDIUM_DEFAULT;
-
- if (phydev->duplex == DUPLEX_HALF)
- mode &= ~AX_MEDIUM_FD;
-
- if (phydev->speed != SPEED_100)
- mode &= ~AX_MEDIUM_PS;
- }
-
- asix_write_medium_mode(dev, mode, 0);
- phy_print_status(phydev);
- usbnet_link_change(dev, phydev->link, 0);
-}
-
int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
{
int ret;
@@ -752,7 +736,6 @@ static void ax88772_mac_link_down(struct phylink_config *config,
struct usbnet *dev = netdev_priv(to_net_dev(config->dev));
asix_write_medium_mode(dev, 0, 0);
- usbnet_link_change(dev, false, false);
}
static void ax88772_mac_link_up(struct phylink_config *config,
@@ -783,7 +766,6 @@ static void ax88772_mac_link_up(struct phylink_config *config,
m |= AX_MEDIUM_RFC;
asix_write_medium_mode(dev, m, 0);
- usbnet_link_change(dev, true, false);
}
static const struct phylink_mac_ops ax88772_phylink_mac_ops = {
@@ -1350,10 +1328,9 @@ static const struct driver_info ax88772_info = {
.description = "ASIX AX88772 USB 2.0 Ethernet",
.bind = ax88772_bind,
.unbind = ax88772_unbind,
- .status = asix_status,
.reset = ax88772_reset,
.stop = ax88772_stop,
- .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET,
+ .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
.rx_fixup = asix_rx_fixup_common,
.tx_fixup = asix_tx_fixup,
};
@@ -1362,11 +1339,9 @@ static const struct driver_info ax88772b_info = {
.description = "ASIX AX88772B USB 2.0 Ethernet",
.bind = ax88772_bind,
.unbind = ax88772_unbind,
- .status = asix_status,
.reset = ax88772_reset,
.stop = ax88772_stop,
- .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
- FLAG_MULTI_PACKET,
+ .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
.rx_fixup = asix_rx_fixup_common,
.tx_fixup = asix_tx_fixup,
.data = FLAG_EEPROM_MAC,
@@ -1376,11 +1351,9 @@ static const struct driver_info lxausb_t1l_info = {
.description = "Linux Automation GmbH USB 10Base-T1L",
.bind = ax88772_bind,
.unbind = ax88772_unbind,
- .status = asix_status,
.reset = ax88772_reset,
.stop = ax88772_stop,
- .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
- FLAG_MULTI_PACKET,
+ .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
.rx_fixup = asix_rx_fixup_common,
.tx_fixup = asix_tx_fixup,
.data = FLAG_EEPROM_MAC,
@@ -1412,10 +1383,8 @@ static const struct driver_info hg20f9_info = {
.description = "HG20F9 USB 2.0 Ethernet",
.bind = ax88772_bind,
.unbind = ax88772_unbind,
- .status = asix_status,
.reset = ax88772_reset,
- .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
- FLAG_MULTI_PACKET,
+ .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_MULTI_PACKET,
.rx_fixup = asix_rx_fixup_common,
.tx_fixup = asix_tx_fixup,
.data = FLAG_EEPROM_MAC,
ASIX AX88772B based USB 10/100 Ethernet adapter doesn't come up ("carrier off"), despite the built-in 100BASE-FX PHY positive link indication. The internal PHY is configured (using EEPROM) in fixed 100 Mbps full duplex mode. The primary problem appears to be using carrier_netif_{on,off}() while, at the same time, delegating carrier management to phylink. Use only the latter and remove "manual control" in the asix driver. I don't have any other AX88772 board here, but the problem doesn't seem specific to a particular board or settings - it's probably timing-dependent. Remove unused asix_adjust_link() as well. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>