@@ -190,6 +190,19 @@ static struct qcom_geni_serial_port qcom_geni_console_port = {
},
};
+static const struct serial_rs485 qcom_geni_rs485_supported = {
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND | SER_RS485_RTS_ON_SEND,
+};
+
+static void qcom_geni_set_rts_pin(struct uart_port *uport, bool pin_state)
+{
+ u32 rfr = UART_MANUAL_RFR_EN;
+
+ /* Set the logical level of RTS GPIO pin based on the bool variable. */
+ rfr |= pin_state ? UART_RFR_NOT_READY : UART_RFR_READY;
+ writel(rfr, uport->membase + SE_UART_MANUAL_RFR);
+}
+
static int qcom_geni_serial_request_port(struct uart_port *uport)
{
struct platform_device *pdev = to_platform_device(uport->dev);
@@ -637,6 +650,7 @@ static void qcom_geni_serial_start_tx_dma(struct uart_port *uport)
struct tty_port *tport = &uport->state->port;
unsigned int xmit_size;
u8 *tail;
+ bool pin_state;
int ret;
if (port->tx_dma_addr)
@@ -648,6 +662,12 @@ static void qcom_geni_serial_start_tx_dma(struct uart_port *uport)
xmit_size = kfifo_out_linear_ptr(&tport->xmit_fifo, &tail,
UART_XMIT_SIZE);
+ if (uport->rs485.flags & SER_RS485_ENABLED) {
+ /* For RS485 mode, the RTS can be set/cleared before transmission */
+ pin_state = !!(uport->rs485.flags & SER_RS485_RTS_ON_SEND);
+ qcom_geni_set_rts_pin(uport, pin_state);
+ }
+
qcom_geni_serial_setup_tx(uport, xmit_size);
ret = geni_se_tx_dma_prep(&port->se, tail, xmit_size,
@@ -1017,6 +1037,7 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
u32 dma_rx_status;
struct uart_port *uport = dev;
bool drop_rx = false;
+ bool pin_state;
struct tty_port *tport = &uport->state->port;
struct qcom_geni_serial_port *port = to_dev_port(uport);
@@ -1055,8 +1076,17 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
}
if (dma) {
- if (dma_tx_status & TX_DMA_DONE)
+ if (dma_tx_status & TX_DMA_DONE) {
qcom_geni_serial_handle_tx_dma(uport);
+ // Check if RS485 mode is enabled
+ if (uport->rs485.flags & SER_RS485_ENABLED) {
+ // Determine the RTS pin state based on the
+ // RS485 RTS_AFTER_SEND flag.
+ pin_state = !!(uport->rs485.flags & SER_RS485_RTS_AFTER_SEND);
+ // Set or clear the RTS pin according to the determined state
+ qcom_geni_set_rts_pin(uport, pin_state);
+ }
+ }
if (dma_rx_status) {
if (dma_rx_status & RX_RESET_DONE)
@@ -1594,6 +1624,29 @@ static void qcom_geni_serial_pm(struct uart_port *uport,
}
}
+/**
+ * qcom_geni_rs485_config - Configure RS485 settings for the UART port
+ * @uport: Pointer to the UART port structure
+ * @termios: Pointer to the termios structure
+ * @rs485: Pointer to the RS485 configuration structure
+ *
+ * This function configures the RTS (Request to Send) pin behavior for RS485 mode.
+ * When RS485 mode is enabled, the RTS pin is kept in the ACTIVE state.
+ * When RS485 mode is disabled, the RTS pin is controlled by the QUP hardware for auto flow control.
+ *
+ * Return: Always returns 0.
+ */
+
+static int qcom_geni_rs485_config(struct uart_port *uport,
+ struct ktermios *termios, struct serial_rs485 *rs485)
+{
+ if (rs485->flags & SER_RS485_ENABLED)
+ qcom_geni_set_rts_pin(uport, true); // Set RTS pin to ACTIVE state
+ else
+ writel(0, uport->membase + SE_UART_MANUAL_RFR); // Revert to auto flow control
+ return 0;
+}
+
static const struct uart_ops qcom_geni_console_pops = {
.tx_empty = qcom_geni_serial_tx_empty,
.stop_tx = qcom_geni_serial_stop_tx_fifo,
@@ -1686,6 +1739,8 @@ static int qcom_geni_serial_probe(struct platform_device *pdev)
return -EINVAL;
uport->mapbase = res->start;
+ uport->rs485_config = qcom_geni_rs485_config;
+ uport->rs485_supported = qcom_geni_rs485_supported;
port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
port->tx_fifo_width = DEF_FIFO_WIDTH_BITS;
@@ -1751,6 +1806,10 @@ static int qcom_geni_serial_probe(struct platform_device *pdev)
return ret;
}
+ ret = uart_get_rs485_mode(uport);
+ if (ret)
+ return ret;
+
ret = uart_add_one_port(drv, uport);
if (ret)
return ret;
Currently the RTS pin is used as flow control in the UART controller by default.For half-duplex modes, use the RTS pin for direction control to prevent data collisions by allowing only one direction at a time. Utilize the rs485 structure and callbacks in the serial core framework to support half-duplex modes. Use the IOCTL value, 'TIOCSRS485', and the 'struct serial_rs485' supported by the serial framework to implement support for related callbacks. Enable RS485 mode with these callbacks. Signed-off-by: Anup Kulkarni <quic_anupkulk@quicinc.com> --- drivers/tty/serial/qcom_geni_serial.c | 61 ++++++++++++++++++++++++++- 1 file changed, 60 insertions(+), 1 deletion(-)