@@ -1647,7 +1647,7 @@ int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
}
-int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr)
+int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr)
{
struct mmc_command cmd = {};
int err = 0;
@@ -1691,7 +1691,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr)
host->ios.clock = 0;
mmc_set_ios(host);
- if (__mmc_set_signal_voltage(host, signal_voltage)) {
+ if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180)) {
/*
* Voltages may not have been switched, but we've already
* sent CMD11, so a power cycle is required anyway
@@ -48,7 +48,7 @@ struct device_node *mmc_of_find_child_device(struct mmc_host *host,
void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode);
void mmc_set_bus_width(struct mmc_host *host, unsigned int width);
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
-int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr);
+int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr);
int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
void mmc_set_timing(struct mmc_host *host, unsigned int timing);
void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type);
@@ -788,8 +788,7 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
*/
if (!mmc_host_is_spi(host) && rocr &&
((*rocr & 0x41000000) == 0x41000000)) {
- err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
- pocr);
+ err = mmc_set_uhs_voltage(host, pocr);
if (err == -EAGAIN) {
retries--;
goto try_again;
@@ -642,8 +642,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
* to make sure which speed mode should work.
*/
if (!powered_resume && (rocr & ocr & R4_18V_PRESENT)) {
- err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180,
- ocr_card);
+ err = mmc_set_uhs_voltage(host, ocr_card);
if (err == -EAGAIN) {
mmc_sdio_resend_if_cond(host, card);
retries--;
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to 1.8V for UHS mode. To clarify this let's do the following changes. - We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage parameter to the function. Then, let's just remove the parameter as it serves no purpose. - Rename the function to mmc_set_uhs_voltage(). Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> --- drivers/mmc/core/core.c | 4 ++-- drivers/mmc/core/core.h | 2 +- drivers/mmc/core/sd.c | 3 +-- drivers/mmc/core/sdio.c | 3 +-- 4 files changed, 5 insertions(+), 7 deletions(-) -- 1.9.1