@@ -1631,7 +1631,7 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
return ocr;
}
-int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
{
int err = 0;
int old_signal_voltage = host->ios.signal_voltage;
@@ -1691,7 +1691,7 @@ int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr)
host->ios.clock = 0;
mmc_set_ios(host);
- if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180)) {
+ if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180)) {
/*
* Voltages may not have been switched, but we've already
* sent CMD11, so a power cycle is required anyway
@@ -1800,11 +1800,11 @@ void mmc_power_up(struct mmc_host *host, u32 ocr)
mmc_set_initial_state(host);
/* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */
- if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330) == 0)
+ if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330) == 0)
dev_dbg(mmc_dev(host), "Initial signal voltage of 3.3v\n");
- else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180) == 0)
+ else if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180) == 0)
dev_dbg(mmc_dev(host), "Initial signal voltage of 1.8v\n");
- else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120) == 0)
+ else if (mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120) == 0)
dev_dbg(mmc_dev(host), "Initial signal voltage of 1.2v\n");
/*
@@ -49,7 +49,7 @@ struct device_node *mmc_of_find_child_device(struct mmc_host *host,
void mmc_set_bus_width(struct mmc_host *host, unsigned int width);
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr);
int mmc_set_uhs_voltage(struct mmc_host *host, u32 ocr);
-int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
+int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
void mmc_set_timing(struct mmc_host *host, unsigned int timing);
void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type);
int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr,
@@ -1122,14 +1122,14 @@ static int mmc_select_hs_ddr(struct mmc_card *card)
*/
err = -EINVAL;
if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_DDR_1_2V)
- err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
if (err && (card->mmc_avail_type & EXT_CSD_CARD_TYPE_DDR_1_8V))
- err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
/* make sure vccq is 3.3v after switching disaster */
if (err)
- err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330);
return err;
}
@@ -1296,10 +1296,10 @@ static int mmc_select_hs400es(struct mmc_card *card)
}
if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS400_1_2V)
- err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
if (err && card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS400_1_8V)
- err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
/* If fails try again during next card power cycle */
if (err)
@@ -1405,10 +1405,10 @@ static int mmc_select_hs200(struct mmc_card *card)
old_signal_voltage = host->ios.signal_voltage;
if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200_1_2V)
- err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
if (err && card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200_1_8V)
- err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+ err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
/* If fails try again during next card power cycle */
if (err)
@@ -1450,7 +1450,7 @@ static int mmc_select_hs200(struct mmc_card *card)
err:
if (err) {
/* fall back to the old signal voltage, if fails report error */
- if (__mmc_set_signal_voltage(host, old_signal_voltage))
+ if (mmc_set_signal_voltage(host, old_signal_voltage))
err = -EIO;
pr_err("%s: %s failed, error %d\n", mmc_hostname(card->host),
Earlier the mmc_set_signal_voltage() existed, but since it has been renamed to mmc_set_uhs_voltage(), we can now use that name instead. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> --- drivers/mmc/core/core.c | 10 +++++----- drivers/mmc/core/core.h | 2 +- drivers/mmc/core/mmc.c | 16 ++++++++-------- 3 files changed, 14 insertions(+), 14 deletions(-) -- 1.9.1