diff mbox series

[RESEND,v2,44/53] mtd: nand: denali: use interrupt instead of polling for bank reset

Message ID 1490228282-10805-18-git-send-email-yamada.masahiro@socionext.com
State Accepted
Commit d49f5790278d18fd6b8e474397d9abfdf29a48f2
Headers show
Series None | expand

Commit Message

Masahiro Yamada March 23, 2017, 12:17 a.m. UTC
The current bank reset implementation polls the INTR_STATUS register
until interested bits are set.  This is not good because:

- it simply wastes time-slice of the thread which the driver module
  is loaded from.

- The while() loop may continue eternally if no bit is set, for
  example, due to the controller problem.  The denali_wait_for_irq()
  uses wait_for_completion_timeout(), which is safer.

We can use interrupt by moving the denali_reset_bank() call below
the interrupt setup.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

---

Changes in v2:
  - Newly added

 drivers/mtd/nand/denali.c | 28 ++++++++++++++--------------
 1 file changed, 14 insertions(+), 14 deletions(-)

-- 
2.7.4


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
diff mbox series

Patch

diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index ef28411..7609ad6 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -938,24 +938,25 @@  static int denali_setup_data_interface(struct mtd_info *mtd,
 
 static void denali_reset_banks(struct denali_nand_info *denali)
 {
+	u32 irq_status;
 	int i;
 
-	denali_clear_irq_all(denali);
-
 	for (i = 0; i < denali->max_banks; i++) {
-		iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
-		while (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
-			(INTR__RST_COMP | INTR__TIME_OUT)))
-			cpu_relax();
-		if (!(ioread32(denali->flash_reg + INTR_STATUS(i)) &
-		      INTR__INT_ACT))
+		denali->flash_bank = i;
+
+		denali_reset_irq(denali);
+
+		iowrite32(DEVICE_RESET__BANK(i),
+			  denali->flash_reg + DEVICE_RESET);
+
+		irq_status = denali_wait_for_irq(denali,
+			INTR__RST_COMP | INTR__INT_ACT | INTR__TIME_OUT);
+		if (!(irq_status & INTR__INT_ACT))
 			break;
 	}
 
 	dev_dbg(denali->dev, "%d chips connected\n", i);
 	denali->max_banks = i;
-
-	denali_clear_irq_all(denali);
 }
 
 static void denali_hw_init(struct denali_nand_info *denali)
@@ -973,7 +974,6 @@  static void denali_hw_init(struct denali_nand_info *denali)
 	denali->bbtskipbytes = ioread32(denali->flash_reg +
 						SPARE_AREA_SKIP_BYTES);
 	detect_max_banks(denali);
-	denali_reset_banks(denali);
 	iowrite32(0x0F, denali->flash_reg + RB_PIN_ENABLED);
 	iowrite32(CHIP_EN_DONT_CARE__FLAG,
 			denali->flash_reg + CHIP_ENABLE_DONT_CARE);
@@ -1097,9 +1097,6 @@  static void denali_drv_init(struct denali_nand_info *denali)
 	 * element that might be access shared data (interrupt status)
 	 */
 	spin_lock_init(&denali->irq_lock);
-
-	/* indicate that MTD has not selected a valid bank yet */
-	denali->flash_bank = CHIP_SELECT_INVALID;
 }
 
 static int denali_multidev_fixup(struct denali_nand_info *denali)
@@ -1174,6 +1171,9 @@  int denali_init(struct denali_nand_info *denali)
 	}
 
 	denali_enable_irq(denali);
+	denali_reset_banks(denali);
+
+	denali->flash_bank = CHIP_SELECT_INVALID;
 
 	nand_set_flash_node(chip, denali->dev->of_node);