diff mbox series

[02/33] ARM: dts: BCM5301X: Set 5 GHz wireless frequency limits on Netgear R8000

Message ID 1491286366-30720-3-git-send-email-amit.pundir@linaro.org
State New
Headers show
Series Stable commits picked up from lede project | expand

Commit Message

Amit Pundir April 4, 2017, 6:12 a.m. UTC 
From: Rafał Miłecki <rafal@milecki.pl>


Netgear R8000 is a tri-band home router. It has three BCM43602 chipsets
two of them for 5 GHz band. Both seem the same and their firmwares
report the same set of channels. The problem is due to hardware / board
design there are extra limitations that should be respected.

First PHY should be used for U-NII-2 and U-NII-3. Third PHY should be
used for U-NII-1. Using them in a different way may result in wireless
not working or in noticeably reduced performance. Basic version of this
info was provided by Broadcom employee, then it has been verified by me
using original vendor firmware (which has limitations hardcoded in UI).

This patch uses recently introduced ieee80211-freq-limit property to
describe these limitations at DT level.

Referencing PCIe devices in DT required specifying all related bridges.
Below you can see (a bit complex) PCI tree from R8000 that explains all
entries that I needed to put in DT.

0000:00:00.0		14e4:8012	Bridge Device
└─ 0000:01:00.0		14e4:aa52	Network Controller

0001:00:00.0		14e4:8012	Bridge Device
└─ 0001:01:00.0		10b5:8603	Bridge Device
   ├─ 0001:02:01.0	10b5:8603	Bridge Device
   │  └─ 0001:03:00.0	14e4:aa52	Network Controller
   ├─ 0001:02:02.0	10b5:8603	Bridge Device
   │  └─ 0001:04:00.0	14e4:aa52	Network Controller
   ├─ 0001:02:03.0	000d:0000	0x000000
   ├─ 0001:02:04.0	000d:0000	0x000000
   ├─ 0001:02:05.0	000d:0000	0x000000
   ├─ 0001:02:06.0	000d:0000	0x000000
   ├─ (...)
   ├─ 0001:02:1d.0	000d:0000	0x000000
   ├─ 0001:02:1e.0	000d:0000	0x000000
   └─ 0001:02:1f.0	000d:0000	0x000000

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

(cherry picked from commit 5d1f2d2c253037a5d89b48347d90868fa9407102)
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>

---
 arch/arm/boot/dts/bcm4709-netgear-r8000.dts | 48 +++++++++++++++++++++++++++++
 arch/arm/boot/dts/bcm5301x.dtsi             |  8 +++++
 2 files changed, 56 insertions(+)

-- 
2.7.4
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
index ca18151..3551718 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
@@ -107,6 +107,54 @@ 
 	};
 };
 
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,1,0 {
+			reg = <0x0000 0 0 0 0>;
+			ieee80211-freq-limit = <5735000 5835000>;
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@1,0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		bridge@1,1,0 {
+			reg = <0x0000 0 0 0 0>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bridge@1,2,2 {
+				reg = <0x1000 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				wifi@1,4,0 {
+					reg = <0x0000 0 0 0 0>;
+					ieee80211-freq-limit = <5170000 5730000>;
+				};
+			};
+		};
+	};
+};
+
 &usb2 {
 	vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
 };
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index ae4b388..c52711b 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -236,6 +236,14 @@ 
 			#gpio-cells = <2>;
 		};
 
+		pcie0: pcie@12000 {
+			reg = <0x00012000 0x1000>;
+		};
+
+		pcie1: pcie@13000 {
+			reg = <0x00013000 0x1000>;
+		};
+
 		usb2: usb2@21000 {
 			reg = <0x00021000 0x1000>;