diff mbox series

[7/7] arm64: dts: qcom: Add SM8550 Xperia 1 V

Message ID 20240210-topic-1v-v1-7-fda0db38e29b@linaro.org
State Accepted
Commit 39c596304e44781c1950ea0cbf178d6433ff9c71
Headers show
Series [1/7] dt-bindings: ASoC: cs35l45: Add interrupts | expand

Commit Message

Konrad Dybcio Feb. 12, 2024, 1:10 p.m. UTC
Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part
of the SoMC SM8550 Yodo platform.

This commit brings support for:
* Remoteprocs (sans modem for now)
* Flash LED (the notification LED is gone :((((()
* SD Card
* USB (*including SuperSpeed*) + PMIC_GLINK (it's funky, requires a replug
  with an cable flip sometimes..)
* Most regulators
* Part of I2C-connected peripherals (notably no touch due to a
driver bug)
* PCIe0 (PCIe1 is unused)

Do note display via simplefb is not supported, as the display is blanked
upon exiting XBL.

To create a working boot image, you need to run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm8550-sony-xperia-\
yodo-pdx234.dtb > .Image.gz-dtb

mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd.img \
--pagesize 4096 \
--base 0x0 \
--kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 \
--tags_offset 0x100 \
--cmdline "SOME_CMDLINE" \
--dtb_offset 0x1f00000 \
--header_version 2 \
-o boot.img-sony-xperia-pdx234

Then, you need to flash it on the device and get rid of all the
vendor_boot/dtbo mess:

// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system \
vbmeta_system.img

fastboot flash boot boot.img-sony-xperia-pdx234
fastboot erase vendor_boot
fastboot erase recovery
fastboot flash dtbo emptydtbo.img
fastboot erase init_boot // ? I don't remember if it's necessary, sorry
fastboot continue

Where emptydtbo.img is a tiny file that consists of 2 bytes (all zeroes), doing
a "fastboot erase" won't cut it, the bootloader will go crazy and things will
fall apart when it tries to overlay random bytes from an empty partition onto a
perfectly good appended DTB.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   1 +
 .../dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts    | 779 +++++++++++++++++++++
 2 files changed, 780 insertions(+)

Comments

Konrad Dybcio April 4, 2024, 7:41 p.m. UTC | #1
On 2/12/24 18:26, Neil Armstrong wrote:
> On 12/02/2024 14:10, Konrad Dybcio wrote:
>> Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part
>> of the SoMC SM8550 Yodo platform.
>>

[...]

>> +/* TODO: Only one SID of PMR735D seems accessible? */
> 
> 
> What's reported by the cpuinfo pmic array  ?

PMK8550 2.1
PM8550 2.0
PM8550VS 2.0
PM8550VS 2.0
PM8550VS 2.0
PM8550VE 2.0
PM8550VS 2.0
PM8550B 2.0
PMR735D 2.0
PM8010 1.1
PM8010 1.1

Not sure if there's only one or the other one is secure?

> 
> <snip>
> 
> With the pcie thing fixed:
> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>

It's gonna be fine with the recent aux clock additions. If you
have no further comments, I'll happily ask for this to be merged ;)

Konrad
Neil Armstrong April 5, 2024, 7:54 a.m. UTC | #2
On 04/04/2024 21:41, Konrad Dybcio wrote:
> 
> 
> On 2/12/24 18:26, Neil Armstrong wrote:
>> On 12/02/2024 14:10, Konrad Dybcio wrote:
>>> Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part
>>> of the SoMC SM8550 Yodo platform.
>>>
> 
> [...]
> 
>>> +/* TODO: Only one SID of PMR735D seems accessible? */
>>
>>
>> What's reported by the cpuinfo pmic array  ?
> 
> PMK8550 2.1
> PM8550 2.0
> PM8550VS 2.0
> PM8550VS 2.0
> PM8550VS 2.0
> PM8550VE 2.0
> PM8550VS 2.0
> PM8550B 2.0
> PMR735D 2.0
> PM8010 1.1
> PM8010 1.1
> 
> Not sure if there's only one or the other one is secure?
> 
>>
>> <snip>
>>
>> With the pcie thing fixed:
>> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
> 
> It's gonna be fine with the recent aux clock additions. If you
> have no further comments, I'll happily ask for this to be merged ;)

Sure LGTM

> 
> Konrad
David Wronek April 17, 2024, 9:04 a.m. UTC | #3
W dniu 2024-02-12 14:10, Konrad Dybcio napisał(a):
> Add support for Sony Xperia 1 V, a.k.a PDX234. This device is a part
> of the SoMC SM8550 Yodo platform.
> 
> This commit brings support for:
> * Remoteprocs (sans modem for now)
> * Flash LED (the notification LED is gone :((((()
> * SD Card
> * USB (*including SuperSpeed*) + PMIC_GLINK (it's funky, requires a 
> replug
>   with an cable flip sometimes..)
> * Most regulators
> * Part of I2C-connected peripherals (notably no touch due to a
> driver bug)
> * PCIe0 (PCIe1 is unused)
> 
> Do note display via simplefb is not supported, as the display is 
> blanked
> upon exiting XBL.
> 

I also noticed such behaviour on my S24 Ultra. I was pointed out by 
Xilin Wu that on SM8450 or
newer, the display will be turned off by the bootloader if the node 
'/reserved-memory/splash_region'
does not exist in the device tree. Adding it in the device tree for my 
phone made the bootloader
leave the display on. Maybe it's the same case here?

https://git.codelinaro.org/clo/la/abl/tianocore/edk2/-/blob/LA.VENDOR.1.0.r2-09400-WAIPIO.QSSI14.0/QcomModulePkg/Library/BootLib/UpdateDeviceTree.c?ref_type=tags#L220

> To create a working boot image, you need to run:
> cat arch/arm64/boot/Image.gz 
> arch/arm64/boot/dts/qcom/sm8550-sony-xperia-\
> yodo-pdx234.dtb > .Image.gz-dtb
> 
> mkbootimg \
> --kernel .Image.gz-dtb \
> --ramdisk some_initrd.img \
> --pagesize 4096 \
> --base 0x0 \
> --kernel_offset 0x8000 \
> --ramdisk_offset 0x1000000 \
> --tags_offset 0x100 \
> --cmdline "SOME_CMDLINE" \
> --dtb_offset 0x1f00000 \
> --header_version 2 \
> -o boot.img-sony-xperia-pdx234
> 
> Then, you need to flash it on the device and get rid of all the
> vendor_boot/dtbo mess:
> 
> // You have to either pull vbmeta{"","_system"} from
> // /dev/block/bootdevice/by-name/ or build one as a part of AOSP build 
> process
> fastboot --disable-verity --disable-verification flash vbmeta 
> vbmeta.img
> fastboot --disable-verity --disable-verification flash vbmeta_system \
> vbmeta_system.img
> 
> fastboot flash boot boot.img-sony-xperia-pdx234
> fastboot erase vendor_boot
> fastboot erase recovery
> fastboot flash dtbo emptydtbo.img
> fastboot erase init_boot // ? I don't remember if it's necessary, sorry
> fastboot continue
> 
> Where emptydtbo.img is a tiny file that consists of 2 bytes (all 
> zeroes), doing
> a "fastboot erase" won't cut it, the bootloader will go crazy and 
> things will
> fall apart when it tries to overlay random bytes from an empty 
> partition onto a
> perfectly good appended DTB.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile                  |   1 +
>  .../dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts    | 779 
> +++++++++++++++++++++
>  2 files changed, 780 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile 
> b/arch/arm64/boot/dts/qcom/Makefile
> index f7c5662213e4..9bbea531660d 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -237,6 +237,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= 
> sm8450-sony-xperia-nagara-pdx224.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-hdk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-mtp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-qrd.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-sony-xperia-yodo-pdx234.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-mtp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-qrd.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb
> diff --git 
> a/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts 
> b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts
> new file mode 100644
> index 000000000000..85e0d3d66e16
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts
> @@ -0,0 +1,779 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2023, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/firmware/qcom,scm.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include <dt-bindings/sound/cs35l45.h>
> +#include "sm8550.dtsi"
> +#include "pm8010.dtsi"
> +#include "pm8550.dtsi"
> +#include "pm8550b.dtsi"
> +#define PMK8550VE_SID 5
> +#include "pm8550ve.dtsi"
> +#include "pm8550vs.dtsi"
> +#include "pmk8550.dtsi"
> +/* TODO: Only one SID of PMR735D seems accessible? */
> +
> +/delete-node/ &hwfence_shbuf;
> +/delete-node/ &mpss_mem;
> +/delete-node/ &rmtfs_mem;
> +/ {
> +	model = "Sony Xperia 1 V";
> +	compatible = "sony,pdx234", "qcom,sm8550";
> +	chassis-type = "handset";
> +
> +	aliases {
> +		i2c0 = &i2c0;
> +		i2c4 = &i2c4;
> +		i2c10 = &i2c10;
> +		i2c11 = &i2c11;
> +		i2c16 = &i2c_hub_2;
> +		serial0 = &uart7;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		label = "gpio-keys";
> +
> +		pinctrl-0 = <&focus_n &snapshot_n &vol_down_n>;
> +		pinctrl-names = "default";
> +
> +		key-camera-focus {
> +			label = "Camera Focus";
> +			linux,code = <KEY_CAMERA_FOCUS>;
> +			gpios = <&pm8550b_gpios 8 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <15>;
> +			linux,can-disable;
> +			wakeup-source;
> +		};
> +
> +		key-camera-snapshot {
> +			label = "Camera Snapshot";
> +			gpios = <&pm8550b_gpios 7 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_CAMERA>;
> +			debounce-interval = <15>;
> +			linux,can-disable;
> +			wakeup-source;
> +		};
> +
> +		key-volume-down {
> +			label = "Volume Down";
> +			linux,code = <KEY_VOLUMEDOWN>;
> +			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <15>;
> +			linux,can-disable;
> +			wakeup-source;
> +		};
> +	};
> +
> +	pmic-glink {
> +		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
> +		orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		connector@0 {
> +			compatible = "usb-c-connector";
> +			reg = <0>;
> +			power-role = "dual";
> +			data-role = "dual";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					pmic_glink_hs_in: endpoint {
> +						remote-endpoint = <&usb_1_dwc3_hs>;
> +					};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +
> +					pmic_glink_ss_in: endpoint {
> +						remote-endpoint = <&usb_dp_qmpphy_out>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +
> +	reserved-memory {
> +		mpss_mem: mpss-region@89800000 {
> +			reg = <0x0 0x89800000 0x0 0x10800000>;
> +			no-map;
> +		};
> +
> +		splash@b8000000 {
> +			reg = <0x0 0xb8000000 0x0 0x2b00000>;
> +			no-map;
> +		};
> +
> +		hwfence_shbuf: hwfence-shbuf-region@e6440000 {
> +			reg = <0x0 0xe6440000 0x0 0x2dd000>;
> +			no-map;
> +		};
> +
> +		rmtfs_mem: memory@f8b00000 {
> +			compatible = "qcom,rmtfs-mem";
> +			reg = <0x0 0xf8b00000 0x0 0x280000>;
> +			no-map;
> +
> +			qcom,client-id = <1>;
> +			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
> +		};
> +
> +		ramoops@ffd00000 {
> +			compatible = "ramoops";
> +			reg = <0x0 0xffd00000 0x0 0xc0000>;
> +			console-size = <0x40000>;
> +			record-size = <0x1000>;
> +			pmsg-size = <0x40000>;
> +			ecc-size = <16>;
> +		};
> +
> +		rdtag-store-region@ffdc0000 {
> +			reg = <0x0 0xffdc0000 0x0 0x40000>;
> +			no-map;
> +		};
> +	};
> +
> +	vph_pwr: vph-pwr-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vph_pwr";
> +		regulator-min-microvolt = <3700000>;
> +		regulator-max-microvolt = <3700000>;
> +
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +};
> +
> +&apps_rsc {
> +	regulators-0 {
> +		compatible = "qcom,pm8550-rpmh-regulators";
> +		qcom,pmic-id = "b";
> +
> +		pm8550_bob1: bob1 {
> +			regulator-name = "pm8550_bob1";
> +			regulator-min-microvolt = <3416000>;
> +			regulator-max-microvolt = <3960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		/* TODO: bob2 @ 2.704-3.008V doesn't fall into the vreg driver 
> constraints */
> +
> +		pm8550_l1: ldo1 {
> +			regulator-name = "pm8550_l1";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l2: ldo2 {
> +			regulator-name = "pm8550_l2";
> +			regulator-min-microvolt = <3008000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		/* L4 exists in cmd-db, but the board seems to crash on access */
> +
> +		pm8550_l5: ldo5 {
> +			regulator-name = "pm8550_l5";
> +			regulator-min-microvolt = <3104000>;
> +			regulator-max-microvolt = <3104000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l6: ldo6 {
> +			regulator-name = "pm8550_l6";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l7: ldo7 {
> +			regulator-name = "pm8550_l7";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l8: ldo8 {
> +			regulator-name = "pm8550_l8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l9: ldo9 {
> +			regulator-name = "pm8550_l9";
> +			regulator-min-microvolt = <2960000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l10: ldo10 {
> +			regulator-name = "pm8550_l10";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l11: ldo11 {
> +			regulator-name = "pm8550_l11";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1504000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l12: ldo12 {
> +			regulator-name = "pm8550_l12";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l13: ldo13 {
> +			regulator-name = "pm8550_l13";
> +			regulator-min-microvolt = <3000000>;
> +			regulator-max-microvolt = <3000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l14: ldo14 {
> +			regulator-name = "pm8550_l14";
> +			regulator-min-microvolt = <3304000>;
> +			regulator-max-microvolt = <3304000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l15: ldo15 {
> +			regulator-name = "pm8550_l15";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l16: ldo16 {
> +			regulator-name = "pm8550_l16";
> +			regulator-min-microvolt = <2800000>;
> +			regulator-max-microvolt = <2800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550_l17: ldo17 {
> +			regulator-name = "pm8550_l17";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2504000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-1 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "c";
> +
> +		pm8550vs_0_l1: ldo1 {
> +			regulator-name = "pm8550vs_0_l1";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_0_l3: ldo3 {
> +			regulator-name = "pm8550vs_0_l3";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-2 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "d";
> +
> +		pm8550vs_1_l1: ldo1 {
> +			regulator-name = "pm8550vs_1_l1";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <920000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		/* L3 exists in cmd-db, but the board seems to crash on access */
> +	};
> +
> +	regulators-3 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "e";
> +
> +		pm8550vs_2_s4: smps4 {
> +			regulator-name = "pm8550vs_2_s4";
> +			regulator-min-microvolt = <904000>;
> +			regulator-max-microvolt = <984000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_2_s5: smps5 {
> +			regulator-name = "pm8550vs_2_s5";
> +			regulator-min-microvolt = <1010000>;
> +			regulator-max-microvolt = <1120000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_2_l1: ldo1 {
> +			regulator-name = "pm8550vs_2_l1";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_2_l2: ldo2 {
> +			regulator-name = "pm8550vs_2_l2";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <968000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_2_l3: ldo3 {
> +			regulator-name = "pm8550vs_2_l3";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-4 {
> +		compatible = "qcom,pm8550ve-rpmh-regulators";
> +		qcom,pmic-id = "f";
> +
> +		pm8550ve_s4: smps4 {
> +			regulator-name = "pm8550ve_s4";
> +			regulator-min-microvolt = <500000>;
> +			regulator-max-microvolt = <700000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550ve_l1: ldo1 {
> +			regulator-name = "pm8550ve_l1";
> +			regulator-min-microvolt = <912000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550ve_l2: ldo2 {
> +			regulator-name = "pm8550ve_l2";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550ve_l3: ldo3 {
> +			regulator-name = "pm8550ve_l3";
> +			regulator-min-microvolt = <912000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-5 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "g";
> +
> +		pm8550vs_3_s1: smps1 {
> +			regulator-name = "pm8550vs_3_s1";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_s2: smps2 {
> +			regulator-name = "pm8550vs_3_s2";
> +			regulator-min-microvolt = <500000>;
> +			regulator-max-microvolt = <1036000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_s3: smps3 {
> +			regulator-name = "pm8550vs_3_s3";
> +			regulator-min-microvolt = <300000>;
> +			regulator-max-microvolt = <1004000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_s4: smps4 {
> +			regulator-name = "pm8550vs_3_s4";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1352000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_s5: smps5 {
> +			regulator-name = "pm8550vs_3_s5";
> +			regulator-min-microvolt = <500000>;
> +			regulator-max-microvolt = <1004000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_s6: smps6 {
> +			regulator-name = "pm8550vs_3_s6";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_l1: ldo1 {
> +			regulator-name = "pm8550vs_3_l1";
> +			regulator-min-microvolt = <1144000>;
> +			regulator-max-microvolt = <1256000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_l2: ldo2 {
> +			regulator-name = "pm8550vs_3_l2";
> +			regulator-min-microvolt = <1104000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		pm8550vs_3_l3: ldo3 {
> +			regulator-name = "pm8550vs_3_l3";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	/* TODO: Unknown PMIC @ k, l, PM8010 @ m, n */
> +};
> +
> +&gpi_dma1 {
> +	status = "okay";
> +};
> +
> +&gpi_dma2 {
> +	status = "okay";
> +};
> +
> +&i2c_hub_2 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	pmic@75 {
> +		compatible = "dlg,slg51000";
> +		reg = <0x75>;
> +		dlg,cs-gpios = <&pm8550vs_g_gpios 4 GPIO_ACTIVE_HIGH>;
> +
> +		pinctrl-0 = <&cam_pwr_a_cs>;
> +		pinctrl-names = "default";
> +
> +		regulators {
> +			slg51000_a_ldo1: ldo1 {
> +				regulator-name = "slg51000_a_ldo1";
> +				regulator-min-microvolt = <2400000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			slg51000_a_ldo2: ldo2 {
> +				regulator-name = "slg51000_a_ldo2";
> +				regulator-min-microvolt = <2400000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			slg51000_a_ldo3: ldo3 {
> +				regulator-name = "slg51000_a_ldo3";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <3750000>;
> +			};
> +
> +			slg51000_a_ldo4: ldo4 {
> +				regulator-name = "slg51000_a_ldo4";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <3750000>;
> +			};
> +
> +			slg51000_a_ldo5: ldo5 {
> +				regulator-name = "slg51000_a_ldo5";
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1200000>;
> +			};
> +
> +			slg51000_a_ldo6: ldo6 {
> +				regulator-name = "slg51000_a_ldo6";
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1200000>;
> +			};
> +
> +			slg51000_a_ldo7: ldo7 {
> +				regulator-name = "slg51000_a_ldo7";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <3750000>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c_master_hub_0 {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	clock-frequency = <1000000>;
> +	status = "okay";
> +
> +	/* NXP NFC @ 28 */
> +};
> +
> +&i2c4 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	/* LX Semi SW82907 touchscreen @ 28 */
> +};
> +
> +&i2c10 {
> +	clock-frequency = <1000000>;
> +	status = "okay";
> +
> +	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
> +};
> +
> +&i2c11 {
> +	clock-frequency = <1000000>;
> +	status = "okay";
> +
> +	cs35l41_l: speaker-amp@30 {
> +		compatible = "cirrus,cs35l45";
> +		reg = <0x30>;
> +		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>;
> +		cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | 
> CS35L45_ASP_TX_HIZ_DISABLED)>;
> +		#sound-dai-cells = <1>;
> +
> +		cirrus,gpio-ctrl2 {
> +			gpio-ctrl = <0x2>;
> +		};
> +	};
> +
> +	cs35l41_r: speaker-amp@31 {
> +		compatible = "cirrus,cs35l45";
> +		reg = <0x31>;
> +		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>;
> +		cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | 
> CS35L45_ASP_TX_HIZ_DISABLED)>;
> +		#sound-dai-cells = <1>;
> +
> +		cirrus,gpio-ctrl2 {
> +			gpio-ctrl = <0x2>;
> +		};
> +	};
> +};
> +
> +&pcie0 {
> +	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> +	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
> +
> +	pinctrl-0 = <&pcie0_default_state>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +};
> +
> +&pcie0_phy {
> +	vdda-phy-supply = <&pm8550vs_2_l1>;
> +	vdda-pll-supply = <&pm8550vs_2_l3>;
> +
> +	status = "okay";
> +};
> +
> +&pm8550_flash {
> +	status = "okay";
> +
> +	led-0 {
> +		function = LED_FUNCTION_FLASH;
> +		color = <LED_COLOR_ID_WHITE>;
> +		led-sources = <1>, <4>;
> +		led-max-microamp = <500000>;
> +		flash-max-microamp = <1000000>;
> +		flash-max-timeout-us = <1280000>;
> +		function-enumerator = <0>;
> +	};
> +
> +	led-1 {
> +		function = LED_FUNCTION_FLASH;
> +		color = <LED_COLOR_ID_YELLOW>;
> +		led-sources = <2>, <3>;
> +		led-max-microamp = <500000>;
> +		flash-max-microamp = <1000000>;
> +		flash-max-timeout-us = <1280000>;
> +		function-enumerator = <1>;
> +	};
> +};
> +
> +&pm8550_gpios {
> +	vol_down_n: volume-down-n-state {
> +		pins = "gpio6";
> +		function = "normal";
> +		power-source = <1>;
> +		bias-pull-up;
> +		input-enable;
> +	};
> +
> +	sdc2_card_det_n: sd-card-det-n-state {
> +		pins = "gpio12";
> +		function = "normal";
> +		power-source = <1>;
> +		bias-pull-down;
> +		output-disable;
> +		input-enable;
> +	};
> +};
> +
> +&pm8550b_gpios {
> +	snapshot_n: snapshot-n-state {
> +		pins = "gpio7";
> +		function = "normal";
> +		power-source = <1>;
> +		bias-pull-up;
> +		input-enable;
> +	};
> +
> +	focus_n: focus-n-state {
> +		pins = "gpio8";
> +		function = "normal";
> +		power-source = <1>;
> +		bias-pull-up;
> +		input-enable;
> +	};
> +};
> +
> +&pm8550vs_g_gpios {
> +	cam_pwr_a_cs: cam-pwr-a-cs-state {
> +		pins = "gpio4";
> +		function = "normal";
> +		power-source = <0x01>;
> +		drive-push-pull;
> +		output-low;
> +		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
> +	};
> +};
> +
> +&pm8550b_eusb2_repeater {
> +	qcom,tune-usb2-disc-thres = /bits/ 8 <0x6>;
> +	qcom,tune-usb2-amplitude = /bits/ 8 <0xf>;
> +	qcom,tune-usb2-preem = /bits/ 8 <0x7>;
> +	vdd18-supply = <&pm8550_l15>;
> +	vdd3-supply = <&pm8550_l5>;
> +};
> +
> +&pon_pwrkey {
> +	status = "okay";
> +};
> +
> +&pon_resin {
> +	linux,code = <KEY_VOLUMEUP>;
> +	status = "okay";
> +};
> +
> +&qupv3_id_0 {
> +	status = "okay";
> +};
> +
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
> +&remoteproc_adsp {
> +	firmware-name = "qcom/sm8550/Sony/yodo/adsp.mbn",
> +			"qcom/sm8550/Sony/yodo/adsp_dtb.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_cdsp {
> +	firmware-name = "qcom/sm8550/Sony/yodo/cdsp.mbn",
> +			"qcom/sm8550/Sony/yodo/cdsp_dtb.mbn";
> +	status = "okay";
> +};
> +
> +&sdhc_2 {
> +	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>;
> +	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
> +	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
> +	pinctrl-names = "default", "sleep";
> +	vmmc-supply = <&pm8550_l9>;
> +	vqmmc-supply = <&pm8550_l8>;
> +	no-sdio;
> +	no-mmc;
> +	status = "okay";
> +};
> +
> +&sleep_clk {
> +	clock-frequency = <32000>;
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <32 8>;
> +};
> +
> +&uart7 {
> +	status = "okay";
> +};
> +
> +&usb_1 {
> +	status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> +	dr_mode = "otg";
> +	usb-role-switch;
> +};
> +
> +&usb_1_dwc3_hs {
> +	remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> +	remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
> +};
> +
> +&usb_1_hsphy {
> +	vdd-supply = <&pm8550vs_2_l1>;
> +	vdda12-supply = <&pm8550vs_2_l3>;
> +	phys = <&pm8550b_eusb2_repeater>;
> +
> +	status = "okay";
> +};
> +
> +&usb_dp_qmpphy {
> +	vdda-phy-supply = <&pm8550vs_2_l3>;
> +	vdda-pll-supply = <&pm8550ve_l3>;
> +	orientation-switch;
> +
> +	status = "okay";
> +};
> +
> +&usb_dp_qmpphy_out {
> +	remote-endpoint = <&pmic_glink_ss_in>;
> +};
> +
> +&usb_dp_qmpphy_usb_ss_in {
> +	remote-endpoint = <&usb_1_dwc3_ss>;
> +};
> +
> +&xo_board {
> +	clock-frequency = <76800000>;
> +};
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index f7c5662213e4..9bbea531660d 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -237,6 +237,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-sony-xperia-nagara-pdx224.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-sony-xperia-yodo-pdx234.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts
new file mode 100644
index 000000000000..85e0d3d66e16
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8550-sony-xperia-yodo-pdx234.dts
@@ -0,0 +1,779 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/firmware/qcom,scm.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/cs35l45.h>
+#include "sm8550.dtsi"
+#include "pm8010.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+/* TODO: Only one SID of PMR735D seems accessible? */
+
+/delete-node/ &hwfence_shbuf;
+/delete-node/ &mpss_mem;
+/delete-node/ &rmtfs_mem;
+/ {
+	model = "Sony Xperia 1 V";
+	compatible = "sony,pdx234", "qcom,sm8550";
+	chassis-type = "handset";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c4 = &i2c4;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c16 = &i2c_hub_2;
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "gpio-keys";
+
+		pinctrl-0 = <&focus_n &snapshot_n &vol_down_n>;
+		pinctrl-names = "default";
+
+		key-camera-focus {
+			label = "Camera Focus";
+			linux,code = <KEY_CAMERA_FOCUS>;
+			gpios = <&pm8550b_gpios 8 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+
+		key-camera-snapshot {
+			label = "Camera Snapshot";
+			gpios = <&pm8550b_gpios 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_CAMERA>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+		orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_dp_qmpphy_out>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		mpss_mem: mpss-region@89800000 {
+			reg = <0x0 0x89800000 0x0 0x10800000>;
+			no-map;
+		};
+
+		splash@b8000000 {
+			reg = <0x0 0xb8000000 0x0 0x2b00000>;
+			no-map;
+		};
+
+		hwfence_shbuf: hwfence-shbuf-region@e6440000 {
+			reg = <0x0 0xe6440000 0x0 0x2dd000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@f8b00000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0xf8b00000 0x0 0x280000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
+		};
+
+		ramoops@ffd00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xffd00000 0x0 0xc0000>;
+			console-size = <0x40000>;
+			record-size = <0x1000>;
+			pmsg-size = <0x40000>;
+			ecc-size = <16>;
+		};
+
+		rdtag-store-region@ffdc0000 {
+			reg = <0x0 0xffdc0000 0x0 0x40000>;
+			no-map;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		pm8550_bob1: bob1 {
+			regulator-name = "pm8550_bob1";
+			regulator-min-microvolt = <3416000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		/* TODO: bob2 @ 2.704-3.008V doesn't fall into the vreg driver constraints */
+
+		pm8550_l1: ldo1 {
+			regulator-name = "pm8550_l1";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l2: ldo2 {
+			regulator-name = "pm8550_l2";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		/* L4 exists in cmd-db, but the board seems to crash on access */
+
+		pm8550_l5: ldo5 {
+			regulator-name = "pm8550_l5";
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l6: ldo6 {
+			regulator-name = "pm8550_l6";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l7: ldo7 {
+			regulator-name = "pm8550_l7";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l8: ldo8 {
+			regulator-name = "pm8550_l8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l9: ldo9 {
+			regulator-name = "pm8550_l9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l10: ldo10 {
+			regulator-name = "pm8550_l10";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l11: ldo11 {
+			regulator-name = "pm8550_l11";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l12: ldo12 {
+			regulator-name = "pm8550_l12";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l13: ldo13 {
+			regulator-name = "pm8550_l13";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l14: ldo14 {
+			regulator-name = "pm8550_l14";
+			regulator-min-microvolt = <3304000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l15: ldo15 {
+			regulator-name = "pm8550_l15";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l16: ldo16 {
+			regulator-name = "pm8550_l16";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550_l17: ldo17 {
+			regulator-name = "pm8550_l17";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		pm8550vs_0_l1: ldo1 {
+			regulator-name = "pm8550vs_0_l1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_0_l3: ldo3 {
+			regulator-name = "pm8550vs_0_l3";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		pm8550vs_1_l1: ldo1 {
+			regulator-name = "pm8550vs_1_l1";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		/* L3 exists in cmd-db, but the board seems to crash on access */
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		pm8550vs_2_s4: smps4 {
+			regulator-name = "pm8550vs_2_s4";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_2_s5: smps5 {
+			regulator-name = "pm8550vs_2_s5";
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_2_l1: ldo1 {
+			regulator-name = "pm8550vs_2_l1";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_2_l2: ldo2 {
+			regulator-name = "pm8550vs_2_l2";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_2_l3: ldo3 {
+			regulator-name = "pm8550vs_2_l3";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		pm8550ve_s4: smps4 {
+			regulator-name = "pm8550ve_s4";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550ve_l1: ldo1 {
+			regulator-name = "pm8550ve_l1";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550ve_l2: ldo2 {
+			regulator-name = "pm8550ve_l2";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550ve_l3: ldo3 {
+			regulator-name = "pm8550ve_l3";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		pm8550vs_3_s1: smps1 {
+			regulator-name = "pm8550vs_3_s1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_s2: smps2 {
+			regulator-name = "pm8550vs_3_s2";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1036000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_s3: smps3 {
+			regulator-name = "pm8550vs_3_s3";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_s4: smps4 {
+			regulator-name = "pm8550vs_3_s4";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_s5: smps5 {
+			regulator-name = "pm8550vs_3_s5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_s6: smps6 {
+			regulator-name = "pm8550vs_3_s6";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_l1: ldo1 {
+			regulator-name = "pm8550vs_3_l1";
+			regulator-min-microvolt = <1144000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_l2: ldo2 {
+			regulator-name = "pm8550vs_3_l2";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8550vs_3_l3: ldo3 {
+			regulator-name = "pm8550vs_3_l3";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	/* TODO: Unknown PMIC @ k, l, PM8010 @ m, n */
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpi_dma2 {
+	status = "okay";
+};
+
+&i2c_hub_2 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	pmic@75 {
+		compatible = "dlg,slg51000";
+		reg = <0x75>;
+		dlg,cs-gpios = <&pm8550vs_g_gpios 4 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&cam_pwr_a_cs>;
+		pinctrl-names = "default";
+
+		regulators {
+			slg51000_a_ldo1: ldo1 {
+				regulator-name = "slg51000_a_ldo1";
+				regulator-min-microvolt = <2400000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			slg51000_a_ldo2: ldo2 {
+				regulator-name = "slg51000_a_ldo2";
+				regulator-min-microvolt = <2400000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			slg51000_a_ldo3: ldo3 {
+				regulator-name = "slg51000_a_ldo3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3750000>;
+			};
+
+			slg51000_a_ldo4: ldo4 {
+				regulator-name = "slg51000_a_ldo4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3750000>;
+			};
+
+			slg51000_a_ldo5: ldo5 {
+				regulator-name = "slg51000_a_ldo5";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			slg51000_a_ldo6: ldo6 {
+				regulator-name = "slg51000_a_ldo6";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			slg51000_a_ldo7: ldo7 {
+				regulator-name = "slg51000_a_ldo7";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3750000>;
+			};
+		};
+	};
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <1000000>;
+	status = "okay";
+
+	/* NXP NFC @ 28 */
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* LX Semi SW82907 touchscreen @ 28 */
+};
+
+&i2c10 {
+	clock-frequency = <1000000>;
+	status = "okay";
+
+	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
+};
+
+&i2c11 {
+	clock-frequency = <1000000>;
+	status = "okay";
+
+	cs35l41_l: speaker-amp@30 {
+		compatible = "cirrus,cs35l45";
+		reg = <0x30>;
+		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>;
+		cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | CS35L45_ASP_TX_HIZ_DISABLED)>;
+		#sound-dai-cells = <1>;
+
+		cirrus,gpio-ctrl2 {
+			gpio-ctrl = <0x2>;
+		};
+	};
+
+	cs35l41_r: speaker-amp@31 {
+		compatible = "cirrus,cs35l45";
+		reg = <0x31>;
+		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>;
+		cirrus,asp-sdout-hiz-ctrl = <(CS35L45_ASP_TX_HIZ_UNUSED | CS35L45_ASP_TX_HIZ_DISABLED)>;
+		#sound-dai-cells = <1>;
+
+		cirrus,gpio-ctrl2 {
+			gpio-ctrl = <0x2>;
+		};
+	};
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&pm8550vs_2_l1>;
+	vdda-pll-supply = <&pm8550vs_2_l3>;
+
+	status = "okay";
+};
+
+&pm8550_flash {
+	status = "okay";
+
+	led-0 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_WHITE>;
+		led-sources = <1>, <4>;
+		led-max-microamp = <500000>;
+		flash-max-microamp = <1000000>;
+		flash-max-timeout-us = <1280000>;
+		function-enumerator = <0>;
+	};
+
+	led-1 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_YELLOW>;
+		led-sources = <2>, <3>;
+		led-max-microamp = <500000>;
+		flash-max-microamp = <1000000>;
+		flash-max-timeout-us = <1280000>;
+		function-enumerator = <1>;
+	};
+};
+
+&pm8550_gpios {
+	vol_down_n: volume-down-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	sdc2_card_det_n: sd-card-det-n-state {
+		pins = "gpio12";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-down;
+		output-disable;
+		input-enable;
+	};
+};
+
+&pm8550b_gpios {
+	snapshot_n: snapshot-n-state {
+		pins = "gpio7";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	focus_n: focus-n-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pm8550vs_g_gpios {
+	cam_pwr_a_cs: cam-pwr-a-cs-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <0x01>;
+		drive-push-pull;
+		output-low;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+	};
+};
+
+&pm8550b_eusb2_repeater {
+	qcom,tune-usb2-disc-thres = /bits/ 8 <0x6>;
+	qcom,tune-usb2-amplitude = /bits/ 8 <0xf>;
+	qcom,tune-usb2-preem = /bits/ 8 <0x7>;
+	vdd18-supply = <&pm8550_l15>;
+	vdd3-supply = <&pm8550_l5>;
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEUP>;
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/Sony/yodo/adsp.mbn",
+			"qcom/sm8550/Sony/yodo/adsp_dtb.mbn";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8550/Sony/yodo/cdsp.mbn",
+			"qcom/sm8550/Sony/yodo/cdsp_dtb.mbn";
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_HIGH>;
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&pm8550_l9>;
+	vqmmc-supply = <&pm8550_l8>;
+	no-sdio;
+	no-mmc;
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <32 8>;
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&usb_dp_qmpphy_usb_ss_in>;
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&pm8550vs_2_l1>;
+	vdda12-supply = <&pm8550vs_2_l3>;
+	phys = <&pm8550b_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&pm8550vs_2_l3>;
+	vdda-pll-supply = <&pm8550ve_l3>;
+	orientation-switch;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_dp_qmpphy_usb_ss_in {
+	remote-endpoint = <&usb_1_dwc3_ss>;
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};