diff mbox series

[v3,1/3] PCI/AER: Store UNCOR_STATUS bits that might be ANFE in aer_err_info

Message ID 20240417061407.1491361-2-zhenzhong.duan@intel.com
State New
Headers show
Series PCI/AER: Handle Advisory Non-Fatal error | expand

Commit Message

Zhenzhong Duan April 17, 2024, 6:14 a.m. UTC
In some cases the detector of a Non-Fatal Error(NFE) is not the most
appropriate agent to determine the type of the error. For example,
when software performs a configuration read from a non-existent
device or Function, completer will send an ERR_NONFATAL Message.
On some platforms, ERR_NONFATAL results in a System Error, which
breaks normal software probing.

Advisory Non-Fatal Error(ANFE) is a special case that can be used
in above scenario. It is predominantly determined by the role of the
detecting agent (Requester, Completer, or Receiver) and the specific
error. In such cases, an agent with AER signals the NFE (if enabled)
by sending an ERR_COR Message as an advisory to software, instead of
sending ERR_NONFATAL.

When processing an ANFE, ideally both correctable error(CE) status and
uncorrectable error(UE) status should be cleared. However, there is no
way to fully identify the UE associated with ANFE. Even worse, a Fatal
Error(FE) or Non-Fatal Error(NFE) may set the same UE status bit as
ANFE. Treating an ANFE as NFE will reproduce above mentioned issue,
i.e., breaking softwore probing; treating NFE as ANFE will make us
ignoring some UEs which need active recover operation. To avoid clearing
UEs that are not ANFE by accident, the most conservative route is taken
here: If any of the FE/NFE Detected bits is set in Device Status, do not
touch UE status, they should be cleared later by the UE handler. Otherwise,
a specific set of UEs that may be raised as ANFE according to the PCIe
specification will be cleared if their corresponding severity is Non-Fatal.

To achieve above purpose, store UNCOR_STATUS bits that might be ANFE
in aer_err_info.anfe_status. So that those bits could be printed and
processed later.

Tested-by: Yudong Wang <yudong.wang@intel.com>
Co-developed-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
Signed-off-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
---
 drivers/pci/pci.h      |  1 +
 drivers/pci/pcie/aer.c | 45 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 46 insertions(+)

Comments

Jonathan Cameron April 22, 2024, 4:16 p.m. UTC | #1
On Wed, 17 Apr 2024 14:14:05 +0800
Zhenzhong Duan <zhenzhong.duan@intel.com> wrote:

> In some cases the detector of a Non-Fatal Error(NFE) is not the most
> appropriate agent to determine the type of the error. For example,
> when software performs a configuration read from a non-existent
> device or Function, completer will send an ERR_NONFATAL Message.
> On some platforms, ERR_NONFATAL results in a System Error, which
> breaks normal software probing.
> 
> Advisory Non-Fatal Error(ANFE) is a special case that can be used
> in above scenario. It is predominantly determined by the role of the
> detecting agent (Requester, Completer, or Receiver) and the specific
> error. In such cases, an agent with AER signals the NFE (if enabled)
> by sending an ERR_COR Message as an advisory to software, instead of
> sending ERR_NONFATAL.
> 
> When processing an ANFE, ideally both correctable error(CE) status and
> uncorrectable error(UE) status should be cleared. However, there is no
> way to fully identify the UE associated with ANFE. Even worse, a Fatal
> Error(FE) or Non-Fatal Error(NFE) may set the same UE status bit as
> ANFE. Treating an ANFE as NFE will reproduce above mentioned issue,
> i.e., breaking softwore probing; treating NFE as ANFE will make us
> ignoring some UEs which need active recover operation. To avoid clearing
> UEs that are not ANFE by accident, the most conservative route is taken
> here: If any of the FE/NFE Detected bits is set in Device Status, do not
> touch UE status, they should be cleared later by the UE handler. Otherwise,
> a specific set of UEs that may be raised as ANFE according to the PCIe
> specification will be cleared if their corresponding severity is Non-Fatal.
> 
> To achieve above purpose, store UNCOR_STATUS bits that might be ANFE
> in aer_err_info.anfe_status. So that those bits could be printed and
> processed later.
> 
> Tested-by: Yudong Wang <yudong.wang@intel.com>
> Co-developed-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
> Signed-off-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
> Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
> ---
>  drivers/pci/pci.h      |  1 +
>  drivers/pci/pcie/aer.c | 45 ++++++++++++++++++++++++++++++++++++++++++
>  2 files changed, 46 insertions(+)
> 
> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
> index 17fed1846847..3f9eb807f9fd 100644
> --- a/drivers/pci/pci.h
> +++ b/drivers/pci/pci.h
> @@ -412,6 +412,7 @@ struct aer_err_info {
>  
>  	unsigned int status;		/* COR/UNCOR Error Status */
>  	unsigned int mask;		/* COR/UNCOR Error Mask */
> +	unsigned int anfe_status;	/* UNCOR Error Status for ANFE */
>  	struct pcie_tlp_log tlp;	/* TLP Header */
>  };
>  
> diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
> index ac6293c24976..27364ab4b148 100644
> --- a/drivers/pci/pcie/aer.c
> +++ b/drivers/pci/pcie/aer.c
> @@ -107,6 +107,12 @@ struct aer_stats {
>  					PCI_ERR_ROOT_MULTI_COR_RCV |	\
>  					PCI_ERR_ROOT_MULTI_UNCOR_RCV)
>  
> +#define AER_ERR_ANFE_UNC_MASK		(PCI_ERR_UNC_POISON_TLP |	\
> +					PCI_ERR_UNC_COMP_TIME |		\
> +					PCI_ERR_UNC_COMP_ABORT |	\
> +					PCI_ERR_UNC_UNX_COMP |		\
> +					PCI_ERR_UNC_UNSUP)
> +
>  static int pcie_aer_disable;
>  static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
>  
> @@ -1196,6 +1202,41 @@ void aer_recover_queue(int domain, unsigned int bus, unsigned int devfn,
>  EXPORT_SYMBOL_GPL(aer_recover_queue);
>  #endif
>  
> +static void anfe_get_uc_status(struct pci_dev *dev, struct aer_err_info *info)
> +{
> +	u32 uncor_mask, uncor_status;
> +	u16 device_status;
> +	int aer = dev->aer_cap;
> +
> +	if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA, &device_status))
> +		return;
> +	/*
> +	 * Take the most conservative route here. If there are
> +	 * Non-Fatal/Fatal errors detected, do not assume any
> +	 * bit in uncor_status is set by ANFE.
> +	 */
> +	if (device_status & (PCI_EXP_DEVSTA_NFED | PCI_EXP_DEVSTA_FED))
> +		return;
> +

Is there not a race here?  If we happen to get either an NFED or FED 
between the read of device_status above and here we might pick up a status
that corresponds to that (and hence clear something we should not).

Or am I missing that race being close somewhere?

> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_STATUS, &uncor_status);
> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK, &uncor_mask);
> +	/*
> +	 * According to PCIe Base Specification Revision 6.1,
> +	 * Section 6.2.3.2.4, if an UNCOR error is raised as
> +	 * Advisory Non-Fatal error, it will match the following
> +	 * conditions:
> +	 *	a. The severity of the error is Non-Fatal.
> +	 *	b. The error is one of the following:
> +	 *		1. Poisoned TLP           (Section 6.2.3.2.4.3)
> +	 *		2. Completion Timeout     (Section 6.2.3.2.4.4)
> +	 *		3. Completer Abort        (Section 6.2.3.2.4.1)
> +	 *		4. Unexpected Completion  (Section 6.2.3.2.4.5)
> +	 *		5. Unsupported Request    (Section 6.2.3.2.4.1)
> +	 */
> +	info->anfe_status = uncor_status & ~uncor_mask & ~info->severity &
> +			    AER_ERR_ANFE_UNC_MASK;
> +}
> +
>  /**
>   * aer_get_device_error_info - read error status from dev and store it to info
>   * @dev: pointer to the device expected to have a error record
> @@ -1213,6 +1254,7 @@ int aer_get_device_error_info(struct pci_dev *dev, struct aer_err_info *info)
>  
>  	/* Must reset in this function */
>  	info->status = 0;
> +	info->anfe_status = 0;
>  	info->tlp_header_valid = 0;
>  
>  	/* The device might not support AER */
> @@ -1226,6 +1268,9 @@ int aer_get_device_error_info(struct pci_dev *dev, struct aer_err_info *info)
>  			&info->mask);
>  		if (!(info->status & ~info->mask))
>  			return 0;
> +
> +		if (info->status & PCI_ERR_COR_ADV_NFAT)
> +			anfe_get_uc_status(dev, info);
>  	} else if (type == PCI_EXP_TYPE_ROOT_PORT ||
>  		   type == PCI_EXP_TYPE_RC_EC ||
>  		   type == PCI_EXP_TYPE_DOWNSTREAM ||
Zhenzhong Duan April 23, 2024, 2:25 a.m. UTC | #2
>-----Original Message-----
>From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
>Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that might
>be ANFE in aer_err_info
>
>On Wed, 17 Apr 2024 14:14:05 +0800
>Zhenzhong Duan <zhenzhong.duan@intel.com> wrote:
>
>> In some cases the detector of a Non-Fatal Error(NFE) is not the most
>> appropriate agent to determine the type of the error. For example,
>> when software performs a configuration read from a non-existent
>> device or Function, completer will send an ERR_NONFATAL Message.
>> On some platforms, ERR_NONFATAL results in a System Error, which
>> breaks normal software probing.
>>
>> Advisory Non-Fatal Error(ANFE) is a special case that can be used
>> in above scenario. It is predominantly determined by the role of the
>> detecting agent (Requester, Completer, or Receiver) and the specific
>> error. In such cases, an agent with AER signals the NFE (if enabled)
>> by sending an ERR_COR Message as an advisory to software, instead of
>> sending ERR_NONFATAL.
>>
>> When processing an ANFE, ideally both correctable error(CE) status and
>> uncorrectable error(UE) status should be cleared. However, there is no
>> way to fully identify the UE associated with ANFE. Even worse, a Fatal
>> Error(FE) or Non-Fatal Error(NFE) may set the same UE status bit as
>> ANFE. Treating an ANFE as NFE will reproduce above mentioned issue,
>> i.e., breaking softwore probing; treating NFE as ANFE will make us
>> ignoring some UEs which need active recover operation. To avoid clearing
>> UEs that are not ANFE by accident, the most conservative route is taken
>> here: If any of the FE/NFE Detected bits is set in Device Status, do not
>> touch UE status, they should be cleared later by the UE handler. Otherwise,
>> a specific set of UEs that may be raised as ANFE according to the PCIe
>> specification will be cleared if their corresponding severity is Non-Fatal.
>>
>> To achieve above purpose, store UNCOR_STATUS bits that might be ANFE
>> in aer_err_info.anfe_status. So that those bits could be printed and
>> processed later.
>>
>> Tested-by: Yudong Wang <yudong.wang@intel.com>
>> Co-developed-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
>> Signed-off-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
>> Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
>> ---
>>  drivers/pci/pci.h      |  1 +
>>  drivers/pci/pcie/aer.c | 45
>++++++++++++++++++++++++++++++++++++++++++
>>  2 files changed, 46 insertions(+)
>>
>> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
>> index 17fed1846847..3f9eb807f9fd 100644
>> --- a/drivers/pci/pci.h
>> +++ b/drivers/pci/pci.h
>> @@ -412,6 +412,7 @@ struct aer_err_info {
>>
>>  	unsigned int status;		/* COR/UNCOR Error Status */
>>  	unsigned int mask;		/* COR/UNCOR Error Mask */
>> +	unsigned int anfe_status;	/* UNCOR Error Status for ANFE */
>>  	struct pcie_tlp_log tlp;	/* TLP Header */
>>  };
>>
>> diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
>> index ac6293c24976..27364ab4b148 100644
>> --- a/drivers/pci/pcie/aer.c
>> +++ b/drivers/pci/pcie/aer.c
>> @@ -107,6 +107,12 @@ struct aer_stats {
>>  					PCI_ERR_ROOT_MULTI_COR_RCV |
>	\
>>  					PCI_ERR_ROOT_MULTI_UNCOR_RCV)
>>
>> +#define AER_ERR_ANFE_UNC_MASK
>	(PCI_ERR_UNC_POISON_TLP |	\
>> +					PCI_ERR_UNC_COMP_TIME |
>	\
>> +					PCI_ERR_UNC_COMP_ABORT |
>	\
>> +					PCI_ERR_UNC_UNX_COMP |
>	\
>> +					PCI_ERR_UNC_UNSUP)
>> +
>>  static int pcie_aer_disable;
>>  static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
>>
>> @@ -1196,6 +1202,41 @@ void aer_recover_queue(int domain, unsigned
>int bus, unsigned int devfn,
>>  EXPORT_SYMBOL_GPL(aer_recover_queue);
>>  #endif
>>
>> +static void anfe_get_uc_status(struct pci_dev *dev, struct aer_err_info
>*info)
>> +{
>> +	u32 uncor_mask, uncor_status;
>> +	u16 device_status;
>> +	int aer = dev->aer_cap;
>> +
>> +	if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA,
>&device_status))
>> +		return;
>> +	/*
>> +	 * Take the most conservative route here. If there are
>> +	 * Non-Fatal/Fatal errors detected, do not assume any
>> +	 * bit in uncor_status is set by ANFE.
>> +	 */
>> +	if (device_status & (PCI_EXP_DEVSTA_NFED | PCI_EXP_DEVSTA_FED))
>> +		return;
>> +
>
>Is there not a race here?  If we happen to get either an NFED or FED
>between the read of device_status above and here we might pick up a status
>that corresponds to that (and hence clear something we should not).

In this scenario, info->anfe_status is 0.

>
>Or am I missing that race being close somewhere?

The bits leading to NFED or FED is masked out when assigning info->anfe_status.
Bits for FED is masked out by ~info->severity,
bit for NFED is masked out by AER_ERR_ANFE_UNC_MASK.

So we never clear status bits for NFED or FED in ANFE handler.

See below assignment of info->anfe_status.

Thanks
Zhenzhong

>
>> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_STATUS,
>&uncor_status);
>> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK,
>&uncor_mask);
>> +	/*
>> +	 * According to PCIe Base Specification Revision 6.1,
>> +	 * Section 6.2.3.2.4, if an UNCOR error is raised as
>> +	 * Advisory Non-Fatal error, it will match the following
>> +	 * conditions:
>> +	 *	a. The severity of the error is Non-Fatal.
>> +	 *	b. The error is one of the following:
>> +	 *		1. Poisoned TLP           (Section 6.2.3.2.4.3)
>> +	 *		2. Completion Timeout     (Section 6.2.3.2.4.4)
>> +	 *		3. Completer Abort        (Section 6.2.3.2.4.1)
>> +	 *		4. Unexpected Completion  (Section 6.2.3.2.4.5)
>> +	 *		5. Unsupported Request    (Section 6.2.3.2.4.1)
>> +	 */
>> +	info->anfe_status = uncor_status & ~uncor_mask & ~info->severity
>&
>> +			    AER_ERR_ANFE_UNC_MASK;
>> +}
>> +
>>  /**
>>   * aer_get_device_error_info - read error status from dev and store it to
>info
>>   * @dev: pointer to the device expected to have a error record
>> @@ -1213,6 +1254,7 @@ int aer_get_device_error_info(struct pci_dev
>*dev, struct aer_err_info *info)
>>
>>  	/* Must reset in this function */
>>  	info->status = 0;
>> +	info->anfe_status = 0;
>>  	info->tlp_header_valid = 0;
>>
>>  	/* The device might not support AER */
>> @@ -1226,6 +1268,9 @@ int aer_get_device_error_info(struct pci_dev
>*dev, struct aer_err_info *info)
>>  			&info->mask);
>>  		if (!(info->status & ~info->mask))
>>  			return 0;
>> +
>> +		if (info->status & PCI_ERR_COR_ADV_NFAT)
>> +			anfe_get_uc_status(dev, info);
>>  	} else if (type == PCI_EXP_TYPE_ROOT_PORT ||
>>  		   type == PCI_EXP_TYPE_RC_EC ||
>>  		   type == PCI_EXP_TYPE_DOWNSTREAM ||
Jonathan Cameron April 26, 2024, 4:11 p.m. UTC | #3
On Tue, 23 Apr 2024 02:25:05 +0000
"Duan, Zhenzhong" <zhenzhong.duan@intel.com> wrote:

> >-----Original Message-----
> >From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
> >Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that might
> >be ANFE in aer_err_info
> >
> >On Wed, 17 Apr 2024 14:14:05 +0800
> >Zhenzhong Duan <zhenzhong.duan@intel.com> wrote:
> >  
> >> In some cases the detector of a Non-Fatal Error(NFE) is not the most
> >> appropriate agent to determine the type of the error. For example,
> >> when software performs a configuration read from a non-existent
> >> device or Function, completer will send an ERR_NONFATAL Message.
> >> On some platforms, ERR_NONFATAL results in a System Error, which
> >> breaks normal software probing.
> >>
> >> Advisory Non-Fatal Error(ANFE) is a special case that can be used
> >> in above scenario. It is predominantly determined by the role of the
> >> detecting agent (Requester, Completer, or Receiver) and the specific
> >> error. In such cases, an agent with AER signals the NFE (if enabled)
> >> by sending an ERR_COR Message as an advisory to software, instead of
> >> sending ERR_NONFATAL.
> >>
> >> When processing an ANFE, ideally both correctable error(CE) status and
> >> uncorrectable error(UE) status should be cleared. However, there is no
> >> way to fully identify the UE associated with ANFE. Even worse, a Fatal
> >> Error(FE) or Non-Fatal Error(NFE) may set the same UE status bit as
> >> ANFE. Treating an ANFE as NFE will reproduce above mentioned issue,
> >> i.e., breaking softwore probing; treating NFE as ANFE will make us
> >> ignoring some UEs which need active recover operation. To avoid clearing
> >> UEs that are not ANFE by accident, the most conservative route is taken
> >> here: If any of the FE/NFE Detected bits is set in Device Status, do not
> >> touch UE status, they should be cleared later by the UE handler. Otherwise,
> >> a specific set of UEs that may be raised as ANFE according to the PCIe
> >> specification will be cleared if their corresponding severity is Non-Fatal.
> >>
> >> To achieve above purpose, store UNCOR_STATUS bits that might be ANFE
> >> in aer_err_info.anfe_status. So that those bits could be printed and
> >> processed later.
> >>
> >> Tested-by: Yudong Wang <yudong.wang@intel.com>
> >> Co-developed-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
> >> Signed-off-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
> >> Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
> >> ---
> >>  drivers/pci/pci.h      |  1 +
> >>  drivers/pci/pcie/aer.c | 45  
> >++++++++++++++++++++++++++++++++++++++++++  
> >>  2 files changed, 46 insertions(+)
> >>
> >> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
> >> index 17fed1846847..3f9eb807f9fd 100644
> >> --- a/drivers/pci/pci.h
> >> +++ b/drivers/pci/pci.h
> >> @@ -412,6 +412,7 @@ struct aer_err_info {
> >>
> >>  	unsigned int status;		/* COR/UNCOR Error Status */
> >>  	unsigned int mask;		/* COR/UNCOR Error Mask */
> >> +	unsigned int anfe_status;	/* UNCOR Error Status for ANFE */
> >>  	struct pcie_tlp_log tlp;	/* TLP Header */
> >>  };
> >>
> >> diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
> >> index ac6293c24976..27364ab4b148 100644
> >> --- a/drivers/pci/pcie/aer.c
> >> +++ b/drivers/pci/pcie/aer.c
> >> @@ -107,6 +107,12 @@ struct aer_stats {
> >>  					PCI_ERR_ROOT_MULTI_COR_RCV |  
> >	\  
> >>  					PCI_ERR_ROOT_MULTI_UNCOR_RCV)
> >>
> >> +#define AER_ERR_ANFE_UNC_MASK  
> >	(PCI_ERR_UNC_POISON_TLP |	\  
> >> +					PCI_ERR_UNC_COMP_TIME |  
> >	\  
> >> +					PCI_ERR_UNC_COMP_ABORT |  
> >	\  
> >> +					PCI_ERR_UNC_UNX_COMP |  
> >	\  
> >> +					PCI_ERR_UNC_UNSUP)
> >> +
> >>  static int pcie_aer_disable;
> >>  static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
> >>
> >> @@ -1196,6 +1202,41 @@ void aer_recover_queue(int domain, unsigned  
> >int bus, unsigned int devfn,  
> >>  EXPORT_SYMBOL_GPL(aer_recover_queue);
> >>  #endif
> >>
> >> +static void anfe_get_uc_status(struct pci_dev *dev, struct aer_err_info  
> >*info)  
> >> +{
> >> +	u32 uncor_mask, uncor_status;
> >> +	u16 device_status;
> >> +	int aer = dev->aer_cap;
> >> +
> >> +	if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA,  
> >&device_status))  
> >> +		return;
> >> +	/*
> >> +	 * Take the most conservative route here. If there are
> >> +	 * Non-Fatal/Fatal errors detected, do not assume any
> >> +	 * bit in uncor_status is set by ANFE.
> >> +	 */
> >> +	if (device_status & (PCI_EXP_DEVSTA_NFED | PCI_EXP_DEVSTA_FED))
> >> +		return;
> >> +  
> >
> >Is there not a race here?  If we happen to get either an NFED or FED
> >between the read of device_status above and here we might pick up a status
> >that corresponds to that (and hence clear something we should not).  
> 
> In this scenario, info->anfe_status is 0.

OK. In that case what is the point of the check above?
If the code is safe to races, it's safe to go ahead without that check
on what might race.

> 
> >
> >Or am I missing that race being close somewhere?  
> 
> The bits leading to NFED or FED is masked out when assigning info->anfe_status.
> Bits for FED is masked out by ~info->severity,
> bit for NFED is masked out by AER_ERR_ANFE_UNC_MASK.
> 
> So we never clear status bits for NFED or FED in ANFE handler.
> 
> See below assignment of info->anfe_status.
> 
> Thanks
> Zhenzhong
> 
> >  
> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_STATUS,  
> >&uncor_status);  
> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK,  
> >&uncor_mask);  
> >> +	/*
> >> +	 * According to PCIe Base Specification Revision 6.1,
> >> +	 * Section 6.2.3.2.4, if an UNCOR error is raised as
> >> +	 * Advisory Non-Fatal error, it will match the following
> >> +	 * conditions:
> >> +	 *	a. The severity of the error is Non-Fatal.
> >> +	 *	b. The error is one of the following:
> >> +	 *		1. Poisoned TLP           (Section 6.2.3.2.4.3)
> >> +	 *		2. Completion Timeout     (Section 6.2.3.2.4.4)
> >> +	 *		3. Completer Abort        (Section 6.2.3.2.4.1)
> >> +	 *		4. Unexpected Completion  (Section 6.2.3.2.4.5)
> >> +	 *		5. Unsupported Request    (Section 6.2.3.2.4.1)
> >> +	 */
> >> +	info->anfe_status = uncor_status & ~uncor_mask & ~info->severity  
> >&  
> >> +			    AER_ERR_ANFE_UNC_MASK;
> >> +}
> >> +
> >>  /**
> >>   * aer_get_device_error_info - read error status from dev and store it to  
> >info  
> >>   * @dev: pointer to the device expected to have a error record
> >> @@ -1213,6 +1254,7 @@ int aer_get_device_error_info(struct pci_dev  
> >*dev, struct aer_err_info *info)  
> >>
> >>  	/* Must reset in this function */
> >>  	info->status = 0;
> >> +	info->anfe_status = 0;
> >>  	info->tlp_header_valid = 0;
> >>
> >>  	/* The device might not support AER */
> >> @@ -1226,6 +1268,9 @@ int aer_get_device_error_info(struct pci_dev  
> >*dev, struct aer_err_info *info)  
> >>  			&info->mask);
> >>  		if (!(info->status & ~info->mask))
> >>  			return 0;
> >> +
> >> +		if (info->status & PCI_ERR_COR_ADV_NFAT)
> >> +			anfe_get_uc_status(dev, info);
> >>  	} else if (type == PCI_EXP_TYPE_ROOT_PORT ||
> >>  		   type == PCI_EXP_TYPE_RC_EC ||
> >>  		   type == PCI_EXP_TYPE_DOWNSTREAM ||  
> 
>
Zhenzhong Duan April 28, 2024, 3:31 a.m. UTC | #4
Hi Jonathan,

>-----Original Message-----
>From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
>Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that might
>be ANFE in aer_err_info
>
>On Tue, 23 Apr 2024 02:25:05 +0000
>"Duan, Zhenzhong" <zhenzhong.duan@intel.com> wrote:
>
>> >-----Original Message-----
>> >From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
>> >Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that
>might
>> >be ANFE in aer_err_info
>> >
>> >On Wed, 17 Apr 2024 14:14:05 +0800
>> >Zhenzhong Duan <zhenzhong.duan@intel.com> wrote:
>> >
>> >> In some cases the detector of a Non-Fatal Error(NFE) is not the most
>> >> appropriate agent to determine the type of the error. For example,
>> >> when software performs a configuration read from a non-existent
>> >> device or Function, completer will send an ERR_NONFATAL Message.
>> >> On some platforms, ERR_NONFATAL results in a System Error, which
>> >> breaks normal software probing.
>> >>
>> >> Advisory Non-Fatal Error(ANFE) is a special case that can be used
>> >> in above scenario. It is predominantly determined by the role of the
>> >> detecting agent (Requester, Completer, or Receiver) and the specific
>> >> error. In such cases, an agent with AER signals the NFE (if enabled)
>> >> by sending an ERR_COR Message as an advisory to software, instead of
>> >> sending ERR_NONFATAL.
>> >>
>> >> When processing an ANFE, ideally both correctable error(CE) status and
>> >> uncorrectable error(UE) status should be cleared. However, there is no
>> >> way to fully identify the UE associated with ANFE. Even worse, a Fatal
>> >> Error(FE) or Non-Fatal Error(NFE) may set the same UE status bit as
>> >> ANFE. Treating an ANFE as NFE will reproduce above mentioned issue,
>> >> i.e., breaking softwore probing; treating NFE as ANFE will make us
>> >> ignoring some UEs which need active recover operation. To avoid
>clearing
>> >> UEs that are not ANFE by accident, the most conservative route is taken
>> >> here: If any of the FE/NFE Detected bits is set in Device Status, do not
>> >> touch UE status, they should be cleared later by the UE handler.
>Otherwise,
>> >> a specific set of UEs that may be raised as ANFE according to the PCIe
>> >> specification will be cleared if their corresponding severity is Non-Fatal.
>> >>
>> >> To achieve above purpose, store UNCOR_STATUS bits that might be
>ANFE
>> >> in aer_err_info.anfe_status. So that those bits could be printed and
>> >> processed later.
>> >>
>> >> Tested-by: Yudong Wang <yudong.wang@intel.com>
>> >> Co-developed-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
>> >> Signed-off-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
>> >> Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
>> >> ---
>> >>  drivers/pci/pci.h      |  1 +
>> >>  drivers/pci/pcie/aer.c | 45
>> >++++++++++++++++++++++++++++++++++++++++++
>> >>  2 files changed, 46 insertions(+)
>> >>
>> >> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
>> >> index 17fed1846847..3f9eb807f9fd 100644
>> >> --- a/drivers/pci/pci.h
>> >> +++ b/drivers/pci/pci.h
>> >> @@ -412,6 +412,7 @@ struct aer_err_info {
>> >>
>> >>  	unsigned int status;		/* COR/UNCOR Error Status */
>> >>  	unsigned int mask;		/* COR/UNCOR Error Mask */
>> >> +	unsigned int anfe_status;	/* UNCOR Error Status for ANFE */
>> >>  	struct pcie_tlp_log tlp;	/* TLP Header */
>> >>  };
>> >>
>> >> diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
>> >> index ac6293c24976..27364ab4b148 100644
>> >> --- a/drivers/pci/pcie/aer.c
>> >> +++ b/drivers/pci/pcie/aer.c
>> >> @@ -107,6 +107,12 @@ struct aer_stats {
>> >>  					PCI_ERR_ROOT_MULTI_COR_RCV |
>> >	\
>> >>  					PCI_ERR_ROOT_MULTI_UNCOR_RCV)
>> >>
>> >> +#define AER_ERR_ANFE_UNC_MASK
>> >	(PCI_ERR_UNC_POISON_TLP |	\
>> >> +					PCI_ERR_UNC_COMP_TIME |
>> >	\
>> >> +					PCI_ERR_UNC_COMP_ABORT |
>> >	\
>> >> +					PCI_ERR_UNC_UNX_COMP |
>> >	\
>> >> +					PCI_ERR_UNC_UNSUP)
>> >> +
>> >>  static int pcie_aer_disable;
>> >>  static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
>> >>
>> >> @@ -1196,6 +1202,41 @@ void aer_recover_queue(int domain,
>unsigned
>> >int bus, unsigned int devfn,
>> >>  EXPORT_SYMBOL_GPL(aer_recover_queue);
>> >>  #endif
>> >>
>> >> +static void anfe_get_uc_status(struct pci_dev *dev, struct
>aer_err_info
>> >*info)
>> >> +{
>> >> +	u32 uncor_mask, uncor_status;
>> >> +	u16 device_status;
>> >> +	int aer = dev->aer_cap;
>> >> +
>> >> +	if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA,
>> >&device_status))
>> >> +		return;
>> >> +	/*
>> >> +	 * Take the most conservative route here. If there are
>> >> +	 * Non-Fatal/Fatal errors detected, do not assume any
>> >> +	 * bit in uncor_status is set by ANFE.
>> >> +	 */
>> >> +	if (device_status & (PCI_EXP_DEVSTA_NFED | PCI_EXP_DEVSTA_FED))
>> >> +		return;
>> >> +
>> >
>> >Is there not a race here?  If we happen to get either an NFED or FED
>> >between the read of device_status above and here we might pick up a
>status
>> >that corresponds to that (and hence clear something we should not).
>>
>> In this scenario, info->anfe_status is 0.
>
>OK. In that case what is the point of the check above?
>If the code is safe to races, it's safe to go ahead without that check
>on what might race.

Good question.
After further digging into the spec, I just found I misunderstood it.
An UNCUR error raised as ANFE can be raised as NFE in different cases,
so info->anfe_status can be nonzero here and the race you mentioned
does exist, the check on PCI_EXP_DEVSTA_FED is also unnecessary.
Sorry for the misleading. I plan to have below change to fix the race:

       unsigned int anfe_status;
       anfe_status = uncor_status & ~uncor_mask & ~info->severity &
                           AER_ERR_ANFE_UNC_MASK;

       if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA, &device_status))
               return;
       /*
        * Take the most conservative route here. If there are
        * Non-Fatal errors detected, do not assume any
        * bit in uncor_status is set by ANFE.
        */
       if (device_status & PCI_EXP_DEVSTA_NFED)
               return;
        info->anfe_status = anfe_status;

With this change, there is still a small window between reading uncor_status
and device_status to leak ANFE, but that's the best we can do and better
than clearing NFE. Let me know if you have better idea😊

Thanks
Zhenzhong

>
>>
>> >
>> >Or am I missing that race being close somewhere?
>>
>> The bits leading to NFED or FED is masked out when assigning info-
>>anfe_status.
>> Bits for FED is masked out by ~info->severity,
>> bit for NFED is masked out by AER_ERR_ANFE_UNC_MASK.
>>
>> So we never clear status bits for NFED or FED in ANFE handler.
>>
>> See below assignment of info->anfe_status.
>>
>> Thanks
>> Zhenzhong
>>
>> >
>> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_STATUS,
>> >&uncor_status);
>> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK,
>> >&uncor_mask);
>> >> +	/*
>> >> +	 * According to PCIe Base Specification Revision 6.1,
>> >> +	 * Section 6.2.3.2.4, if an UNCOR error is raised as
>> >> +	 * Advisory Non-Fatal error, it will match the following
>> >> +	 * conditions:
>> >> +	 *	a. The severity of the error is Non-Fatal.
>> >> +	 *	b. The error is one of the following:
>> >> +	 *		1. Poisoned TLP           (Section 6.2.3.2.4.3)
>> >> +	 *		2. Completion Timeout     (Section 6.2.3.2.4.4)
>> >> +	 *		3. Completer Abort        (Section 6.2.3.2.4.1)
>> >> +	 *		4. Unexpected Completion  (Section 6.2.3.2.4.5)
>> >> +	 *		5. Unsupported Request    (Section 6.2.3.2.4.1)
>> >> +	 */
>> >> +	info->anfe_status = uncor_status & ~uncor_mask & ~info->severity
>> >&
>> >> +			    AER_ERR_ANFE_UNC_MASK;
>> >> +}
>> >> +
>> >>  /**
>> >>   * aer_get_device_error_info - read error status from dev and store it
>to
>> >info
>> >>   * @dev: pointer to the device expected to have a error record
>> >> @@ -1213,6 +1254,7 @@ int aer_get_device_error_info(struct pci_dev
>> >*dev, struct aer_err_info *info)
>> >>
>> >>  	/* Must reset in this function */
>> >>  	info->status = 0;
>> >> +	info->anfe_status = 0;
>> >>  	info->tlp_header_valid = 0;
>> >>
>> >>  	/* The device might not support AER */
>> >> @@ -1226,6 +1268,9 @@ int aer_get_device_error_info(struct pci_dev
>> >*dev, struct aer_err_info *info)
>> >>  			&info->mask);
>> >>  		if (!(info->status & ~info->mask))
>> >>  			return 0;
>> >> +
>> >> +		if (info->status & PCI_ERR_COR_ADV_NFAT)
>> >> +			anfe_get_uc_status(dev, info);
>> >>  	} else if (type == PCI_EXP_TYPE_ROOT_PORT ||
>> >>  		   type == PCI_EXP_TYPE_RC_EC ||
>> >>  		   type == PCI_EXP_TYPE_DOWNSTREAM ||
>>
>>
Jonathan Cameron May 1, 2024, 12:24 p.m. UTC | #5
On Sun, 28 Apr 2024 03:31:11 +0000
"Duan, Zhenzhong" <zhenzhong.duan@intel.com> wrote:

> Hi Jonathan,
> 
> >-----Original Message-----
> >From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
> >Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that might
> >be ANFE in aer_err_info
> >
> >On Tue, 23 Apr 2024 02:25:05 +0000
> >"Duan, Zhenzhong" <zhenzhong.duan@intel.com> wrote:
> >  
> >> >-----Original Message-----
> >> >From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
> >> >Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that  
> >might  
> >> >be ANFE in aer_err_info
> >> >
> >> >On Wed, 17 Apr 2024 14:14:05 +0800
> >> >Zhenzhong Duan <zhenzhong.duan@intel.com> wrote:
> >> >  
> >> >> In some cases the detector of a Non-Fatal Error(NFE) is not the most
> >> >> appropriate agent to determine the type of the error. For example,
> >> >> when software performs a configuration read from a non-existent
> >> >> device or Function, completer will send an ERR_NONFATAL Message.
> >> >> On some platforms, ERR_NONFATAL results in a System Error, which
> >> >> breaks normal software probing.
> >> >>
> >> >> Advisory Non-Fatal Error(ANFE) is a special case that can be used
> >> >> in above scenario. It is predominantly determined by the role of the
> >> >> detecting agent (Requester, Completer, or Receiver) and the specific
> >> >> error. In such cases, an agent with AER signals the NFE (if enabled)
> >> >> by sending an ERR_COR Message as an advisory to software, instead of
> >> >> sending ERR_NONFATAL.
> >> >>
> >> >> When processing an ANFE, ideally both correctable error(CE) status and
> >> >> uncorrectable error(UE) status should be cleared. However, there is no
> >> >> way to fully identify the UE associated with ANFE. Even worse, a Fatal
> >> >> Error(FE) or Non-Fatal Error(NFE) may set the same UE status bit as
> >> >> ANFE. Treating an ANFE as NFE will reproduce above mentioned issue,
> >> >> i.e., breaking softwore probing; treating NFE as ANFE will make us
> >> >> ignoring some UEs which need active recover operation. To avoid  
> >clearing  
> >> >> UEs that are not ANFE by accident, the most conservative route is taken
> >> >> here: If any of the FE/NFE Detected bits is set in Device Status, do not
> >> >> touch UE status, they should be cleared later by the UE handler.  
> >Otherwise,  
> >> >> a specific set of UEs that may be raised as ANFE according to the PCIe
> >> >> specification will be cleared if their corresponding severity is Non-Fatal.
> >> >>
> >> >> To achieve above purpose, store UNCOR_STATUS bits that might be  
> >ANFE  
> >> >> in aer_err_info.anfe_status. So that those bits could be printed and
> >> >> processed later.
> >> >>
> >> >> Tested-by: Yudong Wang <yudong.wang@intel.com>
> >> >> Co-developed-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
> >> >> Signed-off-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
> >> >> Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
> >> >> ---
> >> >>  drivers/pci/pci.h      |  1 +
> >> >>  drivers/pci/pcie/aer.c | 45  
> >> >++++++++++++++++++++++++++++++++++++++++++  
> >> >>  2 files changed, 46 insertions(+)
> >> >>
> >> >> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
> >> >> index 17fed1846847..3f9eb807f9fd 100644
> >> >> --- a/drivers/pci/pci.h
> >> >> +++ b/drivers/pci/pci.h
> >> >> @@ -412,6 +412,7 @@ struct aer_err_info {
> >> >>
> >> >>  	unsigned int status;		/* COR/UNCOR Error Status */
> >> >>  	unsigned int mask;		/* COR/UNCOR Error Mask */
> >> >> +	unsigned int anfe_status;	/* UNCOR Error Status for ANFE */
> >> >>  	struct pcie_tlp_log tlp;	/* TLP Header */
> >> >>  };
> >> >>
> >> >> diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
> >> >> index ac6293c24976..27364ab4b148 100644
> >> >> --- a/drivers/pci/pcie/aer.c
> >> >> +++ b/drivers/pci/pcie/aer.c
> >> >> @@ -107,6 +107,12 @@ struct aer_stats {
> >> >>  					PCI_ERR_ROOT_MULTI_COR_RCV |  
> >> >	\  
> >> >>  					PCI_ERR_ROOT_MULTI_UNCOR_RCV)
> >> >>
> >> >> +#define AER_ERR_ANFE_UNC_MASK  
> >> >	(PCI_ERR_UNC_POISON_TLP |	\  
> >> >> +					PCI_ERR_UNC_COMP_TIME |  
> >> >	\  
> >> >> +					PCI_ERR_UNC_COMP_ABORT |  
> >> >	\  
> >> >> +					PCI_ERR_UNC_UNX_COMP |  
> >> >	\  
> >> >> +					PCI_ERR_UNC_UNSUP)
> >> >> +
> >> >>  static int pcie_aer_disable;
> >> >>  static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
> >> >>
> >> >> @@ -1196,6 +1202,41 @@ void aer_recover_queue(int domain,  
> >unsigned  
> >> >int bus, unsigned int devfn,  
> >> >>  EXPORT_SYMBOL_GPL(aer_recover_queue);
> >> >>  #endif
> >> >>
> >> >> +static void anfe_get_uc_status(struct pci_dev *dev, struct  
> >aer_err_info  
> >> >*info)  
> >> >> +{
> >> >> +	u32 uncor_mask, uncor_status;
> >> >> +	u16 device_status;
> >> >> +	int aer = dev->aer_cap;
> >> >> +
> >> >> +	if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA,  
> >> >&device_status))  
> >> >> +		return;
> >> >> +	/*
> >> >> +	 * Take the most conservative route here. If there are
> >> >> +	 * Non-Fatal/Fatal errors detected, do not assume any
> >> >> +	 * bit in uncor_status is set by ANFE.
> >> >> +	 */
> >> >> +	if (device_status & (PCI_EXP_DEVSTA_NFED | PCI_EXP_DEVSTA_FED))
> >> >> +		return;
> >> >> +  
> >> >
> >> >Is there not a race here?  If we happen to get either an NFED or FED
> >> >between the read of device_status above and here we might pick up a  
> >status  
> >> >that corresponds to that (and hence clear something we should not).  
> >>
> >> In this scenario, info->anfe_status is 0.  
> >
> >OK. In that case what is the point of the check above?
> >If the code is safe to races, it's safe to go ahead without that check
> >on what might race.  
> 
> Good question.
> After further digging into the spec, I just found I misunderstood it.
> An UNCUR error raised as ANFE can be raised as NFE in different cases,
> so info->anfe_status can be nonzero here and the race you mentioned
> does exist, the check on PCI_EXP_DEVSTA_FED is also unnecessary.
> Sorry for the misleading. I plan to have below change to fix the race:
> 
>        unsigned int anfe_status;
>        anfe_status = uncor_status & ~uncor_mask & ~info->severity &
>                            AER_ERR_ANFE_UNC_MASK;
> 
>        if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA, &device_status))
>                return;
>        /*
>         * Take the most conservative route here. If there are
>         * Non-Fatal errors detected, do not assume any
>         * bit in uncor_status is set by ANFE.
>         */
>        if (device_status & PCI_EXP_DEVSTA_NFED)
>                return;
>         info->anfe_status = anfe_status;
> 
> With this change, there is still a small window between reading uncor_status
> and device_status to leak ANFE, but that's the best we can do and better
> than clearing NFE. Let me know if you have better idea😊

Worth leaving some breadcrumbs about there being a race (so a comment)
and explain what the side effects of hitting that race are (lost info
on the error I think, but not a missed error)?
> 
> Thanks
> Zhenzhong
> 
> >  
> >>  
> >> >
> >> >Or am I missing that race being close somewhere?  
> >>
> >> The bits leading to NFED or FED is masked out when assigning info-
> >>anfe_status.
> >> Bits for FED is masked out by ~info->severity,
> >> bit for NFED is masked out by AER_ERR_ANFE_UNC_MASK.
> >>
> >> So we never clear status bits for NFED or FED in ANFE handler.
> >>
> >> See below assignment of info->anfe_status.
> >>
> >> Thanks
> >> Zhenzhong
> >>  
> >> >  
> >> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_STATUS,  
> >> >&uncor_status);  
> >> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK,  
> >> >&uncor_mask);  
> >> >> +	/*
> >> >> +	 * According to PCIe Base Specification Revision 6.1,
> >> >> +	 * Section 6.2.3.2.4, if an UNCOR error is raised as
> >> >> +	 * Advisory Non-Fatal error, it will match the following
> >> >> +	 * conditions:
> >> >> +	 *	a. The severity of the error is Non-Fatal.
> >> >> +	 *	b. The error is one of the following:
> >> >> +	 *		1. Poisoned TLP           (Section 6.2.3.2.4.3)
> >> >> +	 *		2. Completion Timeout     (Section 6.2.3.2.4.4)
> >> >> +	 *		3. Completer Abort        (Section 6.2.3.2.4.1)
> >> >> +	 *		4. Unexpected Completion  (Section 6.2.3.2.4.5)
> >> >> +	 *		5. Unsupported Request    (Section 6.2.3.2.4.1)
> >> >> +	 */
> >> >> +	info->anfe_status = uncor_status & ~uncor_mask & ~info->severity  
> >> >&  
> >> >> +			    AER_ERR_ANFE_UNC_MASK;
> >> >> +}
> >> >> +
> >> >>  /**
> >> >>   * aer_get_device_error_info - read error status from dev and store it  
> >to  
> >> >info  
> >> >>   * @dev: pointer to the device expected to have a error record
> >> >> @@ -1213,6 +1254,7 @@ int aer_get_device_error_info(struct pci_dev  
> >> >*dev, struct aer_err_info *info)  
> >> >>
> >> >>  	/* Must reset in this function */
> >> >>  	info->status = 0;
> >> >> +	info->anfe_status = 0;
> >> >>  	info->tlp_header_valid = 0;
> >> >>
> >> >>  	/* The device might not support AER */
> >> >> @@ -1226,6 +1268,9 @@ int aer_get_device_error_info(struct pci_dev  
> >> >*dev, struct aer_err_info *info)  
> >> >>  			&info->mask);
> >> >>  		if (!(info->status & ~info->mask))
> >> >>  			return 0;
> >> >> +
> >> >> +		if (info->status & PCI_ERR_COR_ADV_NFAT)
> >> >> +			anfe_get_uc_status(dev, info);
> >> >>  	} else if (type == PCI_EXP_TYPE_ROOT_PORT ||
> >> >>  		   type == PCI_EXP_TYPE_RC_EC ||
> >> >>  		   type == PCI_EXP_TYPE_DOWNSTREAM ||  
> >>
> >>  
>
Zhenzhong Duan May 3, 2024, 11:10 a.m. UTC | #6
>-----Original Message-----
>From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
>Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that might
>be ANFE in aer_err_info
>
>On Sun, 28 Apr 2024 03:31:11 +0000
>"Duan, Zhenzhong" <zhenzhong.duan@intel.com> wrote:
>
>> Hi Jonathan,
>>
>> >-----Original Message-----
>> >From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
>> >Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that
>might
>> >be ANFE in aer_err_info
>> >
>> >On Tue, 23 Apr 2024 02:25:05 +0000
>> >"Duan, Zhenzhong" <zhenzhong.duan@intel.com> wrote:
>> >
>> >> >-----Original Message-----
>> >> >From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
>> >> >Subject: Re: [PATCH v3 1/3] PCI/AER: Store UNCOR_STATUS bits that
>> >might
>> >> >be ANFE in aer_err_info
>> >> >
>> >> >On Wed, 17 Apr 2024 14:14:05 +0800
>> >> >Zhenzhong Duan <zhenzhong.duan@intel.com> wrote:
>> >> >
>> >> >> In some cases the detector of a Non-Fatal Error(NFE) is not the most
>> >> >> appropriate agent to determine the type of the error. For example,
>> >> >> when software performs a configuration read from a non-existent
>> >> >> device or Function, completer will send an ERR_NONFATAL Message.
>> >> >> On some platforms, ERR_NONFATAL results in a System Error, which
>> >> >> breaks normal software probing.
>> >> >>
>> >> >> Advisory Non-Fatal Error(ANFE) is a special case that can be used
>> >> >> in above scenario. It is predominantly determined by the role of the
>> >> >> detecting agent (Requester, Completer, or Receiver) and the specific
>> >> >> error. In such cases, an agent with AER signals the NFE (if enabled)
>> >> >> by sending an ERR_COR Message as an advisory to software, instead
>of
>> >> >> sending ERR_NONFATAL.
>> >> >>
>> >> >> When processing an ANFE, ideally both correctable error(CE) status
>and
>> >> >> uncorrectable error(UE) status should be cleared. However, there is
>no
>> >> >> way to fully identify the UE associated with ANFE. Even worse, a
>Fatal
>> >> >> Error(FE) or Non-Fatal Error(NFE) may set the same UE status bit as
>> >> >> ANFE. Treating an ANFE as NFE will reproduce above mentioned
>issue,
>> >> >> i.e., breaking softwore probing; treating NFE as ANFE will make us
>> >> >> ignoring some UEs which need active recover operation. To avoid
>> >clearing
>> >> >> UEs that are not ANFE by accident, the most conservative route is
>taken
>> >> >> here: If any of the FE/NFE Detected bits is set in Device Status, do
>not
>> >> >> touch UE status, they should be cleared later by the UE handler.
>> >Otherwise,
>> >> >> a specific set of UEs that may be raised as ANFE according to the
>PCIe
>> >> >> specification will be cleared if their corresponding severity is Non-
>Fatal.
>> >> >>
>> >> >> To achieve above purpose, store UNCOR_STATUS bits that might be
>> >ANFE
>> >> >> in aer_err_info.anfe_status. So that those bits could be printed and
>> >> >> processed later.
>> >> >>
>> >> >> Tested-by: Yudong Wang <yudong.wang@intel.com>
>> >> >> Co-developed-by: "Wang, Qingshun"
><qingshun.wang@linux.intel.com>
>> >> >> Signed-off-by: "Wang, Qingshun" <qingshun.wang@linux.intel.com>
>> >> >> Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
>> >> >> ---
>> >> >>  drivers/pci/pci.h      |  1 +
>> >> >>  drivers/pci/pcie/aer.c | 45
>> >> >++++++++++++++++++++++++++++++++++++++++++
>> >> >>  2 files changed, 46 insertions(+)
>> >> >>
>> >> >> diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
>> >> >> index 17fed1846847..3f9eb807f9fd 100644
>> >> >> --- a/drivers/pci/pci.h
>> >> >> +++ b/drivers/pci/pci.h
>> >> >> @@ -412,6 +412,7 @@ struct aer_err_info {
>> >> >>
>> >> >>  	unsigned int status;		/* COR/UNCOR Error Status
>*/
>> >> >>  	unsigned int mask;		/* COR/UNCOR Error Mask */
>> >> >> +	unsigned int anfe_status;	/* UNCOR Error Status for
>ANFE */
>> >> >>  	struct pcie_tlp_log tlp;	/* TLP Header */
>> >> >>  };
>> >> >>
>> >> >> diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
>> >> >> index ac6293c24976..27364ab4b148 100644
>> >> >> --- a/drivers/pci/pcie/aer.c
>> >> >> +++ b/drivers/pci/pcie/aer.c
>> >> >> @@ -107,6 +107,12 @@ struct aer_stats {
>> >> >>
>	PCI_ERR_ROOT_MULTI_COR_RCV |
>> >> >	\
>> >> >>
>	PCI_ERR_ROOT_MULTI_UNCOR_RCV)
>> >> >>
>> >> >> +#define AER_ERR_ANFE_UNC_MASK
>> >> >	(PCI_ERR_UNC_POISON_TLP |	\
>> >> >> +					PCI_ERR_UNC_COMP_TIME |
>> >> >	\
>> >> >> +					PCI_ERR_UNC_COMP_ABORT
>|
>> >> >	\
>> >> >> +					PCI_ERR_UNC_UNX_COMP |
>> >> >	\
>> >> >> +					PCI_ERR_UNC_UNSUP)
>> >> >> +
>> >> >>  static int pcie_aer_disable;
>> >> >>  static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
>> >> >>
>> >> >> @@ -1196,6 +1202,41 @@ void aer_recover_queue(int domain,
>> >unsigned
>> >> >int bus, unsigned int devfn,
>> >> >>  EXPORT_SYMBOL_GPL(aer_recover_queue);
>> >> >>  #endif
>> >> >>
>> >> >> +static void anfe_get_uc_status(struct pci_dev *dev, struct
>> >aer_err_info
>> >> >*info)
>> >> >> +{
>> >> >> +	u32 uncor_mask, uncor_status;
>> >> >> +	u16 device_status;
>> >> >> +	int aer = dev->aer_cap;
>> >> >> +
>> >> >> +	if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA,
>> >> >&device_status))
>> >> >> +		return;
>> >> >> +	/*
>> >> >> +	 * Take the most conservative route here. If there are
>> >> >> +	 * Non-Fatal/Fatal errors detected, do not assume any
>> >> >> +	 * bit in uncor_status is set by ANFE.
>> >> >> +	 */
>> >> >> +	if (device_status & (PCI_EXP_DEVSTA_NFED |
>PCI_EXP_DEVSTA_FED))
>> >> >> +		return;
>> >> >> +
>> >> >
>> >> >Is there not a race here?  If we happen to get either an NFED or FED
>> >> >between the read of device_status above and here we might pick up a
>> >status
>> >> >that corresponds to that (and hence clear something we should not).
>> >>
>> >> In this scenario, info->anfe_status is 0.
>> >
>> >OK. In that case what is the point of the check above?
>> >If the code is safe to races, it's safe to go ahead without that check
>> >on what might race.
>>
>> Good question.
>> After further digging into the spec, I just found I misunderstood it.
>> An UNCUR error raised as ANFE can be raised as NFE in different cases,
>> so info->anfe_status can be nonzero here and the race you mentioned
>> does exist, the check on PCI_EXP_DEVSTA_FED is also unnecessary.
>> Sorry for the misleading. I plan to have below change to fix the race:
>>
>>        unsigned int anfe_status;
>>        anfe_status = uncor_status & ~uncor_mask & ~info->severity &
>>                            AER_ERR_ANFE_UNC_MASK;
>>
>>        if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA, &device_status))
>>                return;
>>        /*
>>         * Take the most conservative route here. If there are
>>         * Non-Fatal errors detected, do not assume any
>>         * bit in uncor_status is set by ANFE.
>>         */
>>        if (device_status & PCI_EXP_DEVSTA_NFED)
>>                return;
>>         info->anfe_status = anfe_status;
>>
>> With this change, there is still a small window between reading
>uncor_status
>> and device_status to leak ANFE, but that's the best we can do and better
>> than clearing NFE. Let me know if you have better idea😊
>
>Worth leaving some breadcrumbs about there being a race (so a comment)
>and explain what the side effects of hitting that race are (lost info
>on the error I think, but not a missed error)?

Plan to add below comments, let me know if it's unclear for you:

"If there is another ANFE between reading uncor_status and clearing
PCI_ERR_COR_ADV_NFAT bit in cor_status register, that ANFE isn't
recorded in info->anfe_status. It will be read out as NFE in next
uncor_status register reading and processed by NFE handler."

Thanks
Zhenzhong

>>
>> Thanks
>> Zhenzhong
>>
>> >
>> >>
>> >> >
>> >> >Or am I missing that race being close somewhere?
>> >>
>> >> The bits leading to NFED or FED is masked out when assigning info-
>> >>anfe_status.
>> >> Bits for FED is masked out by ~info->severity,
>> >> bit for NFED is masked out by AER_ERR_ANFE_UNC_MASK.
>> >>
>> >> So we never clear status bits for NFED or FED in ANFE handler.
>> >>
>> >> See below assignment of info->anfe_status.
>> >>
>> >> Thanks
>> >> Zhenzhong
>> >>
>> >> >
>> >> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_STATUS,
>> >> >&uncor_status);
>> >> >> +	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK,
>> >> >&uncor_mask);
>> >> >> +	/*
>> >> >> +	 * According to PCIe Base Specification Revision 6.1,
>> >> >> +	 * Section 6.2.3.2.4, if an UNCOR error is raised as
>> >> >> +	 * Advisory Non-Fatal error, it will match the following
>> >> >> +	 * conditions:
>> >> >> +	 *	a. The severity of the error is Non-Fatal.
>> >> >> +	 *	b. The error is one of the following:
>> >> >> +	 *		1. Poisoned TLP           (Section 6.2.3.2.4.3)
>> >> >> +	 *		2. Completion Timeout     (Section 6.2.3.2.4.4)
>> >> >> +	 *		3. Completer Abort        (Section 6.2.3.2.4.1)
>> >> >> +	 *		4. Unexpected Completion  (Section
>6.2.3.2.4.5)
>> >> >> +	 *		5. Unsupported Request    (Section 6.2.3.2.4.1)
>> >> >> +	 */
>> >> >> +	info->anfe_status = uncor_status & ~uncor_mask & ~info-
>>severity
>> >> >&
>> >> >> +			    AER_ERR_ANFE_UNC_MASK;
>> >> >> +}
>> >> >> +
>> >> >>  /**
>> >> >>   * aer_get_device_error_info - read error status from dev and store
>it
>> >to
>> >> >info
>> >> >>   * @dev: pointer to the device expected to have a error record
>> >> >> @@ -1213,6 +1254,7 @@ int aer_get_device_error_info(struct
>pci_dev
>> >> >*dev, struct aer_err_info *info)
>> >> >>
>> >> >>  	/* Must reset in this function */
>> >> >>  	info->status = 0;
>> >> >> +	info->anfe_status = 0;
>> >> >>  	info->tlp_header_valid = 0;
>> >> >>
>> >> >>  	/* The device might not support AER */
>> >> >> @@ -1226,6 +1268,9 @@ int aer_get_device_error_info(struct
>pci_dev
>> >> >*dev, struct aer_err_info *info)
>> >> >>  			&info->mask);
>> >> >>  		if (!(info->status & ~info->mask))
>> >> >>  			return 0;
>> >> >> +
>> >> >> +		if (info->status & PCI_ERR_COR_ADV_NFAT)
>> >> >> +			anfe_get_uc_status(dev, info);
>> >> >>  	} else if (type == PCI_EXP_TYPE_ROOT_PORT ||
>> >> >>  		   type == PCI_EXP_TYPE_RC_EC ||
>> >> >>  		   type == PCI_EXP_TYPE_DOWNSTREAM ||
>> >>
>> >>
>>
diff mbox series

Patch

diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index 17fed1846847..3f9eb807f9fd 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -412,6 +412,7 @@  struct aer_err_info {
 
 	unsigned int status;		/* COR/UNCOR Error Status */
 	unsigned int mask;		/* COR/UNCOR Error Mask */
+	unsigned int anfe_status;	/* UNCOR Error Status for ANFE */
 	struct pcie_tlp_log tlp;	/* TLP Header */
 };
 
diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
index ac6293c24976..27364ab4b148 100644
--- a/drivers/pci/pcie/aer.c
+++ b/drivers/pci/pcie/aer.c
@@ -107,6 +107,12 @@  struct aer_stats {
 					PCI_ERR_ROOT_MULTI_COR_RCV |	\
 					PCI_ERR_ROOT_MULTI_UNCOR_RCV)
 
+#define AER_ERR_ANFE_UNC_MASK		(PCI_ERR_UNC_POISON_TLP |	\
+					PCI_ERR_UNC_COMP_TIME |		\
+					PCI_ERR_UNC_COMP_ABORT |	\
+					PCI_ERR_UNC_UNX_COMP |		\
+					PCI_ERR_UNC_UNSUP)
+
 static int pcie_aer_disable;
 static pci_ers_result_t aer_root_reset(struct pci_dev *dev);
 
@@ -1196,6 +1202,41 @@  void aer_recover_queue(int domain, unsigned int bus, unsigned int devfn,
 EXPORT_SYMBOL_GPL(aer_recover_queue);
 #endif
 
+static void anfe_get_uc_status(struct pci_dev *dev, struct aer_err_info *info)
+{
+	u32 uncor_mask, uncor_status;
+	u16 device_status;
+	int aer = dev->aer_cap;
+
+	if (pcie_capability_read_word(dev, PCI_EXP_DEVSTA, &device_status))
+		return;
+	/*
+	 * Take the most conservative route here. If there are
+	 * Non-Fatal/Fatal errors detected, do not assume any
+	 * bit in uncor_status is set by ANFE.
+	 */
+	if (device_status & (PCI_EXP_DEVSTA_NFED | PCI_EXP_DEVSTA_FED))
+		return;
+
+	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_STATUS, &uncor_status);
+	pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK, &uncor_mask);
+	/*
+	 * According to PCIe Base Specification Revision 6.1,
+	 * Section 6.2.3.2.4, if an UNCOR error is raised as
+	 * Advisory Non-Fatal error, it will match the following
+	 * conditions:
+	 *	a. The severity of the error is Non-Fatal.
+	 *	b. The error is one of the following:
+	 *		1. Poisoned TLP           (Section 6.2.3.2.4.3)
+	 *		2. Completion Timeout     (Section 6.2.3.2.4.4)
+	 *		3. Completer Abort        (Section 6.2.3.2.4.1)
+	 *		4. Unexpected Completion  (Section 6.2.3.2.4.5)
+	 *		5. Unsupported Request    (Section 6.2.3.2.4.1)
+	 */
+	info->anfe_status = uncor_status & ~uncor_mask & ~info->severity &
+			    AER_ERR_ANFE_UNC_MASK;
+}
+
 /**
  * aer_get_device_error_info - read error status from dev and store it to info
  * @dev: pointer to the device expected to have a error record
@@ -1213,6 +1254,7 @@  int aer_get_device_error_info(struct pci_dev *dev, struct aer_err_info *info)
 
 	/* Must reset in this function */
 	info->status = 0;
+	info->anfe_status = 0;
 	info->tlp_header_valid = 0;
 
 	/* The device might not support AER */
@@ -1226,6 +1268,9 @@  int aer_get_device_error_info(struct pci_dev *dev, struct aer_err_info *info)
 			&info->mask);
 		if (!(info->status & ~info->mask))
 			return 0;
+
+		if (info->status & PCI_ERR_COR_ADV_NFAT)
+			anfe_get_uc_status(dev, info);
 	} else if (type == PCI_EXP_TYPE_ROOT_PORT ||
 		   type == PCI_EXP_TYPE_RC_EC ||
 		   type == PCI_EXP_TYPE_DOWNSTREAM ||