| Message ID | cover.1686045347.git.quic_varada@quicinc.com |
|---|---|
| Headers | show |
| Series | Enable IPQ9754 USB | expand |
On 07/06/2023 13:48, Varadarajan Narayanan wrote: > Add USB phy and controller related nodes > > SS PHY need two supplies and HS PHY needs three supplies. 0.925V > and 3.3V are from fixed regulators and 1.8V is generated from > PMIC's LDO > > Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> > --- > Changes in v12: > - Rebase > Changes in v11: > - Rename dwc_0 -> usb_0_dwc3 > Changes in v10: > - Fix regulator definitions > Changes in v8: > - Change clocks order to match the bindings > Changes in v7: > - Change com_aux -> cfg_ahb > Changes in v6: > - Introduce fixed regulators for the phy > - Resolved all 'make dtbs_check' messages > > Changes in v5: > - Fix additional comments > - Edit nodes to match with qcom,sc8280xp-qmp-usb3-uni-phy.yaml > - 'make dtbs_check' giving the following messages since > ipq9574 doesn't have power domains. Hope this is ok > > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml > > Changes in v4: > - Use newer bindings without subnodes > - Fix coding style issues > > Changes in v3: > - Insert the nodes at proper location > > Changes in v2: > - Fixed issues flagged by Krzysztof > - Fix issues reported by make dtbs_check > - Remove NOC related clocks (to be added with proper > interconnect support) > --- > arch/arm64/boot/dts/qcom/ipq9574.dtsi | 104 ++++++++++++++++++++++++++++++++++ > 1 file changed, 104 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > index 0baeb10..8f7c59e 100644 > --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi > +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > @@ -94,6 +94,24 @@ > }; > }; > > + fixed_3p3: s3300 { > + compatible = "regulator-fixed"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-name = "fixed_3p3"; > + }; > + > + fixed_0p925: s0925 { > + compatible = "regulator-fixed"; > + regulator-min-microvolt = <925000>; > + regulator-max-microvolt = <925000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-name = "fixed_0p925"; > + }; > + These regulators are provided by the board, not by the SoC itself. As such they should go to the board DT files. Please excuse me for not noticing this during earlier review stage. I was too concentrated on not making them non-USB-specific. > memory@40000000 { > device_type = "memory"; > /* We expect the bootloader to fill in the size */ > @@ -465,6 +483,92 @@ > status = "disabled"; > }; > > + usb_0_qusbphy: phy@7b000 { > + compatible = "qcom,ipq9574-qusb2-phy"; > + reg = <0x0007b000 0x180>; > + #phy-cells = <0>; > + > + clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > + <&xo_board_clk>; > + clock-names = "cfg_ahb", > + "ref"; > + > + resets = <&gcc GCC_QUSB2_0_PHY_BCR>; > + status = "disabled"; > + }; > + > + usb_0_qmpphy: phy@7d000 { > + compatible = "qcom,ipq9574-qmp-usb3-phy"; > + reg = <0x0007d000 0xa00>; > + #phy-cells = <0>; > + > + clocks = <&gcc GCC_USB0_AUX_CLK>, > + <&xo_board_clk>, > + <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > + <&gcc GCC_USB0_PIPE_CLK>; > + clock-names = "aux", > + "ref", > + "cfg_ahb", > + "pipe"; > + > + resets = <&gcc GCC_USB0_PHY_BCR>, > + <&gcc GCC_USB3PHY_0_PHY_BCR>; > + reset-names = "phy", > + "phy_phy"; > + > + status = "disabled"; > + > + #clock-cells = <0>; > + clock-output-names = "usb0_pipe_clk"; > + }; > + > + usb3: usb@8af8800 { > + compatible = "qcom,ipq9574-dwc3", "qcom,dwc3"; > + reg = <0x08af8800 0x400>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + clocks = <&gcc GCC_SNOC_USB_CLK>, > + <&gcc GCC_USB0_MASTER_CLK>, > + <&gcc GCC_ANOC_USB_AXI_CLK>, > + <&gcc GCC_USB0_SLEEP_CLK>, > + <&gcc GCC_USB0_MOCK_UTMI_CLK>; > + > + clock-names = "cfg_noc", > + "core", > + "iface", > + "sleep", > + "mock_utmi"; > + > + assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>, > + <&gcc GCC_USB0_MOCK_UTMI_CLK>; > + assigned-clock-rates = <200000000>, > + <24000000>; > + > + interrupts-extended = <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "pwr_event"; > + > + resets = <&gcc GCC_USB_BCR>; > + status = "disabled"; > + > + usb_0_dwc3: usb@8a00000 { > + compatible = "snps,dwc3"; > + reg = <0x8a00000 0xcd00>; > + clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>; > + clock-names = "ref"; > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; > + phys = <&usb_0_qusbphy>, <&usb_0_qmpphy>; > + phy-names = "usb2-phy", "usb3-phy"; > + tx-fifo-resize; > + snps,is-utmi-l1-suspend; > + snps,hird-threshold = /bits/ 8 <0x0>; > + snps,dis_u2_susphy_quirk; > + snps,dis_u3_susphy_quirk; > + dr_mode = "host"; > + }; > + }; > + > intc: interrupt-controller@b000000 { > compatible = "qcom,msm-qgic2"; > reg = <0x0b000000 0x1000>, /* GICD */
On 07/06/2023 12:48, Varadarajan Narayanan wrote: > Add USB phy and controller related nodes > > SS PHY need two supplies and HS PHY needs three supplies. 0.925V > and 3.3V are from fixed regulators and 1.8V is generated from > PMIC's LDO > > Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> > --- > Changes in v12: > - Rebase > Changes in v11: > - Rename dwc_0 -> usb_0_dwc3 > Changes in v10: > - Fix regulator definitions > Changes in v8: > - Change clocks order to match the bindings > Changes in v7: > - Change com_aux -> cfg_ahb > Changes in v6: > - Introduce fixed regulators for the phy > - Resolved all 'make dtbs_check' messages > > Changes in v5: > - Fix additional comments > - Edit nodes to match with qcom,sc8280xp-qmp-usb3-uni-phy.yaml > - 'make dtbs_check' giving the following messages since > ipq9574 doesn't have power domains. Hope this is ok > > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml > > Changes in v4: > - Use newer bindings without subnodes > - Fix coding style issues > > Changes in v3: > - Insert the nodes at proper location > > Changes in v2: > - Fixed issues flagged by Krzysztof > - Fix issues reported by make dtbs_check > - Remove NOC related clocks (to be added with proper > interconnect support) > --- > arch/arm64/boot/dts/qcom/ipq9574.dtsi | 104 ++++++++++++++++++++++++++++++++++ > 1 file changed, 104 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > index 0baeb10..8f7c59e 100644 > --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi > +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > @@ -94,6 +94,24 @@ > }; > }; > > + fixed_3p3: s3300 { Use regulator- prefix for node name. > + compatible = "regulator-fixed"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-name = "fixed_3p3"; > + }; > + > + fixed_0p925: s0925 { > + compatible = "regulator-fixed"; > + regulator-min-microvolt = <925000>; > + regulator-max-microvolt = <925000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-name = "fixed_0p925"; > + }; > + > memory@40000000 { > device_type = "memory"; > /* We expect the bootloader to fill in the size */ > @@ -465,6 +483,92 @@ > status = "disabled"; > }; > > + usb_0_qusbphy: phy@7b000 { > + compatible = "qcom,ipq9574-qusb2-phy"; > + reg = <0x0007b000 0x180>; > + #phy-cells = <0>; > + > + clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > + <&xo_board_clk>; > + clock-names = "cfg_ahb", > + "ref"; > + > + resets = <&gcc GCC_QUSB2_0_PHY_BCR>; > + status = "disabled"; > + }; > + > + usb_0_qmpphy: phy@7d000 { > + compatible = "qcom,ipq9574-qmp-usb3-phy"; > + reg = <0x0007d000 0xa00>; > + #phy-cells = <0>; > + > + clocks = <&gcc GCC_USB0_AUX_CLK>, > + <&xo_board_clk>, > + <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > + <&gcc GCC_USB0_PIPE_CLK>; > + clock-names = "aux", > + "ref", > + "cfg_ahb", > + "pipe"; > + > + resets = <&gcc GCC_USB0_PHY_BCR>, > + <&gcc GCC_USB3PHY_0_PHY_BCR>; > + reset-names = "phy", > + "phy_phy"; > + > + status = "disabled"; status is always the last property. > + > + #clock-cells = <0>; > + clock-output-names = "usb0_pipe_clk"; > + }; > + > + usb3: usb@8af8800 { > + compatible = "qcom,ipq9574-dwc3", "qcom,dwc3"; > + reg = <0x08af8800 0x400>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + clocks = <&gcc GCC_SNOC_USB_CLK>, > + <&gcc GCC_USB0_MASTER_CLK>, > + <&gcc GCC_ANOC_USB_AXI_CLK>, > + <&gcc GCC_USB0_SLEEP_CLK>, > + <&gcc GCC_USB0_MOCK_UTMI_CLK>; > + > + clock-names = "cfg_noc", > + "core", > + "iface", > + "sleep", > + "mock_utmi"; > + > + assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>, > + <&gcc GCC_USB0_MOCK_UTMI_CLK>; > + assigned-clock-rates = <200000000>, > + <24000000>; > + > + interrupts-extended = <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "pwr_event"; > + > + resets = <&gcc GCC_USB_BCR>; > + status = "disabled"; > + > + usb_0_dwc3: usb@8a00000 { > + compatible = "snps,dwc3"; > + reg = <0x8a00000 0xcd00>; > + clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>; > + clock-names = "ref"; > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; > + phys = <&usb_0_qusbphy>, <&usb_0_qmpphy>; > + phy-names = "usb2-phy", "usb3-phy"; > + tx-fifo-resize; > + snps,is-utmi-l1-suspend; > + snps,hird-threshold = /bits/ 8 <0x0>; > + snps,dis_u2_susphy_quirk; > + snps,dis_u3_susphy_quirk; > + dr_mode = "host"; Why is this property of the SoC? Best regards, Krzysztof
On Wed, Jun 07, 2023 at 02:07:31PM +0300, Dmitry Baryshkov wrote: > On 07/06/2023 13:48, Varadarajan Narayanan wrote: > >Add USB phy and controller related nodes > > > >SS PHY need two supplies and HS PHY needs three supplies. 0.925V > >and 3.3V are from fixed regulators and 1.8V is generated from > >PMIC's LDO > > > >Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > >Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> > >--- > > Changes in v12: > > - Rebase > > Changes in v11: > > - Rename dwc_0 -> usb_0_dwc3 > > Changes in v10: > > - Fix regulator definitions > > Changes in v8: > > - Change clocks order to match the bindings > > Changes in v7: > > - Change com_aux -> cfg_ahb > > Changes in v6: > > - Introduce fixed regulators for the phy > > - Resolved all 'make dtbs_check' messages > > > > Changes in v5: > > - Fix additional comments > > - Edit nodes to match with qcom,sc8280xp-qmp-usb3-uni-phy.yaml > > - 'make dtbs_check' giving the following messages since > > ipq9574 doesn't have power domains. Hope this is ok > > > > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property > > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml > > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property > > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml > > > > Changes in v4: > > - Use newer bindings without subnodes > > - Fix coding style issues > > > > Changes in v3: > > - Insert the nodes at proper location > > > > Changes in v2: > > - Fixed issues flagged by Krzysztof > > - Fix issues reported by make dtbs_check > > - Remove NOC related clocks (to be added with proper > > interconnect support) > >--- > > arch/arm64/boot/dts/qcom/ipq9574.dtsi | 104 ++++++++++++++++++++++++++++++++++ > > 1 file changed, 104 insertions(+) > > > >diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > >index 0baeb10..8f7c59e 100644 > >--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi > >+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > >@@ -94,6 +94,24 @@ > > }; > > }; > >+ fixed_3p3: s3300 { > >+ compatible = "regulator-fixed"; > >+ regulator-min-microvolt = <3300000>; > >+ regulator-max-microvolt = <3300000>; > >+ regulator-boot-on; > >+ regulator-always-on; > >+ regulator-name = "fixed_3p3"; > >+ }; > >+ > >+ fixed_0p925: s0925 { > >+ compatible = "regulator-fixed"; > >+ regulator-min-microvolt = <925000>; > >+ regulator-max-microvolt = <925000>; > >+ regulator-boot-on; > >+ regulator-always-on; > >+ regulator-name = "fixed_0p925"; > >+ }; > >+ > > These regulators are provided by the board, not by the SoC itself. As such > they should go to the board DT files. Please excuse me for not noticing this > during earlier review stage. I was too concentrated on not making them > non-USB-specific. Will move it to board dts. Thanks Varada > > memory@40000000 { > > device_type = "memory"; > > /* We expect the bootloader to fill in the size */ > >@@ -465,6 +483,92 @@ > > status = "disabled"; > > }; > >+ usb_0_qusbphy: phy@7b000 { > >+ compatible = "qcom,ipq9574-qusb2-phy"; > >+ reg = <0x0007b000 0x180>; > >+ #phy-cells = <0>; > >+ > >+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > >+ <&xo_board_clk>; > >+ clock-names = "cfg_ahb", > >+ "ref"; > >+ > >+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>; > >+ status = "disabled"; > >+ }; > >+ > >+ usb_0_qmpphy: phy@7d000 { > >+ compatible = "qcom,ipq9574-qmp-usb3-phy"; > >+ reg = <0x0007d000 0xa00>; > >+ #phy-cells = <0>; > >+ > >+ clocks = <&gcc GCC_USB0_AUX_CLK>, > >+ <&xo_board_clk>, > >+ <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > >+ <&gcc GCC_USB0_PIPE_CLK>; > >+ clock-names = "aux", > >+ "ref", > >+ "cfg_ahb", > >+ "pipe"; > >+ > >+ resets = <&gcc GCC_USB0_PHY_BCR>, > >+ <&gcc GCC_USB3PHY_0_PHY_BCR>; > >+ reset-names = "phy", > >+ "phy_phy"; > >+ > >+ status = "disabled"; > >+ > >+ #clock-cells = <0>; > >+ clock-output-names = "usb0_pipe_clk"; > >+ }; > >+ > >+ usb3: usb@8af8800 { > >+ compatible = "qcom,ipq9574-dwc3", "qcom,dwc3"; > >+ reg = <0x08af8800 0x400>; > >+ #address-cells = <1>; > >+ #size-cells = <1>; > >+ ranges; > >+ > >+ clocks = <&gcc GCC_SNOC_USB_CLK>, > >+ <&gcc GCC_USB0_MASTER_CLK>, > >+ <&gcc GCC_ANOC_USB_AXI_CLK>, > >+ <&gcc GCC_USB0_SLEEP_CLK>, > >+ <&gcc GCC_USB0_MOCK_UTMI_CLK>; > >+ > >+ clock-names = "cfg_noc", > >+ "core", > >+ "iface", > >+ "sleep", > >+ "mock_utmi"; > >+ > >+ assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>, > >+ <&gcc GCC_USB0_MOCK_UTMI_CLK>; > >+ assigned-clock-rates = <200000000>, > >+ <24000000>; > >+ > >+ interrupts-extended = <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; > >+ interrupt-names = "pwr_event"; > >+ > >+ resets = <&gcc GCC_USB_BCR>; > >+ status = "disabled"; > >+ > >+ usb_0_dwc3: usb@8a00000 { > >+ compatible = "snps,dwc3"; > >+ reg = <0x8a00000 0xcd00>; > >+ clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>; > >+ clock-names = "ref"; > >+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; > >+ phys = <&usb_0_qusbphy>, <&usb_0_qmpphy>; > >+ phy-names = "usb2-phy", "usb3-phy"; > >+ tx-fifo-resize; > >+ snps,is-utmi-l1-suspend; > >+ snps,hird-threshold = /bits/ 8 <0x0>; > >+ snps,dis_u2_susphy_quirk; > >+ snps,dis_u3_susphy_quirk; > >+ dr_mode = "host"; > >+ }; > >+ }; > >+ > > intc: interrupt-controller@b000000 { > > compatible = "qcom,msm-qgic2"; > > reg = <0x0b000000 0x1000>, /* GICD */ > > -- > With best wishes > Dmitry >
On Wed, Jun 07, 2023 at 08:50:41PM +0200, Krzysztof Kozlowski wrote: > On 07/06/2023 12:48, Varadarajan Narayanan wrote: > > Add USB phy and controller related nodes > > > > SS PHY need two supplies and HS PHY needs three supplies. 0.925V > > and 3.3V are from fixed regulators and 1.8V is generated from > > PMIC's LDO > > > > Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > > Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com> > > --- > > Changes in v12: > > - Rebase > > Changes in v11: > > - Rename dwc_0 -> usb_0_dwc3 > > Changes in v10: > > - Fix regulator definitions > > Changes in v8: > > - Change clocks order to match the bindings > > Changes in v7: > > - Change com_aux -> cfg_ahb > > Changes in v6: > > - Introduce fixed regulators for the phy > > - Resolved all 'make dtbs_check' messages > > > > Changes in v5: > > - Fix additional comments > > - Edit nodes to match with qcom,sc8280xp-qmp-usb3-uni-phy.yaml > > - 'make dtbs_check' giving the following messages since > > ipq9574 doesn't have power domains. Hope this is ok > > > > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property > > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml > > /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property > > From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml > > > > Changes in v4: > > - Use newer bindings without subnodes > > - Fix coding style issues > > > > Changes in v3: > > - Insert the nodes at proper location > > > > Changes in v2: > > - Fixed issues flagged by Krzysztof > > - Fix issues reported by make dtbs_check > > - Remove NOC related clocks (to be added with proper > > interconnect support) > > --- > > arch/arm64/boot/dts/qcom/ipq9574.dtsi | 104 ++++++++++++++++++++++++++++++++++ > > 1 file changed, 104 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > > index 0baeb10..8f7c59e 100644 > > --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi > > +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi > > @@ -94,6 +94,24 @@ > > }; > > }; > > > > + fixed_3p3: s3300 { > > Use regulator- prefix for node name. ok > > + compatible = "regulator-fixed"; > > + regulator-min-microvolt = <3300000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-boot-on; > > + regulator-always-on; > > + regulator-name = "fixed_3p3"; > > + }; > > + > > + fixed_0p925: s0925 { > > + compatible = "regulator-fixed"; > > + regulator-min-microvolt = <925000>; > > + regulator-max-microvolt = <925000>; > > + regulator-boot-on; > > + regulator-always-on; > > + regulator-name = "fixed_0p925"; > > + }; > > + > > memory@40000000 { > > device_type = "memory"; > > /* We expect the bootloader to fill in the size */ > > @@ -465,6 +483,92 @@ > > status = "disabled"; > > }; > > > > + usb_0_qusbphy: phy@7b000 { > > + compatible = "qcom,ipq9574-qusb2-phy"; > > + reg = <0x0007b000 0x180>; > > + #phy-cells = <0>; > > + > > + clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > > + <&xo_board_clk>; > > + clock-names = "cfg_ahb", > > + "ref"; > > + > > + resets = <&gcc GCC_QUSB2_0_PHY_BCR>; > > + status = "disabled"; > > + }; > > + > > + usb_0_qmpphy: phy@7d000 { > > + compatible = "qcom,ipq9574-qmp-usb3-phy"; > > + reg = <0x0007d000 0xa00>; > > + #phy-cells = <0>; > > + > > + clocks = <&gcc GCC_USB0_AUX_CLK>, > > + <&xo_board_clk>, > > + <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, > > + <&gcc GCC_USB0_PIPE_CLK>; > > + clock-names = "aux", > > + "ref", > > + "cfg_ahb", > > + "pipe"; > > + > > + resets = <&gcc GCC_USB0_PHY_BCR>, > > + <&gcc GCC_USB3PHY_0_PHY_BCR>; > > + reset-names = "phy", > > + "phy_phy"; > > + > > + status = "disabled"; > > status is always the last property. ok > > + > > + #clock-cells = <0>; > > + clock-output-names = "usb0_pipe_clk"; > > + }; > > + > > + usb3: usb@8af8800 { > > + compatible = "qcom,ipq9574-dwc3", "qcom,dwc3"; > > + reg = <0x08af8800 0x400>; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + clocks = <&gcc GCC_SNOC_USB_CLK>, > > + <&gcc GCC_USB0_MASTER_CLK>, > > + <&gcc GCC_ANOC_USB_AXI_CLK>, > > + <&gcc GCC_USB0_SLEEP_CLK>, > > + <&gcc GCC_USB0_MOCK_UTMI_CLK>; > > + > > + clock-names = "cfg_noc", > > + "core", > > + "iface", > > + "sleep", > > + "mock_utmi"; > > + > > + assigned-clocks = <&gcc GCC_USB0_MASTER_CLK>, > > + <&gcc GCC_USB0_MOCK_UTMI_CLK>; > > + assigned-clock-rates = <200000000>, > > + <24000000>; > > + > > + interrupts-extended = <&intc GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "pwr_event"; > > + > > + resets = <&gcc GCC_USB_BCR>; > > + status = "disabled"; > > + > > + usb_0_dwc3: usb@8a00000 { > > + compatible = "snps,dwc3"; > > + reg = <0x8a00000 0xcd00>; > > + clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>; > > + clock-names = "ref"; > > + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; > > + phys = <&usb_0_qusbphy>, <&usb_0_qmpphy>; > > + phy-names = "usb2-phy", "usb3-phy"; > > + tx-fifo-resize; > > + snps,is-utmi-l1-suspend; > > + snps,hird-threshold = /bits/ 8 <0x0>; > > + snps,dis_u2_susphy_quirk; > > + snps,dis_u3_susphy_quirk; > > + dr_mode = "host"; > > Why is this property of the SoC? Will remove it from here. It is present in ipq9574-rdp433.dts Thanks Varada
This patch series adds the relevant phy and controller configurations for enabling USB on IPQ9754 Portions of the patchset have been merged. Please see https://lore.kernel.org/lkml/ZGN9gchu7dRb6QwC@matsya/ [v12]: - In dtsi usb@8a00000 -> usb@8af8800 [v11]: - Rename dwc_0 -> usb_0_dwc3 - Minor change in qcom,sc8280xp-qmp-usb3-uni-phy.yaml to factor in latest updates to the file [v10]: - Fix regulator definitions - Address couple of other comments [v9]: - Update bindings to make power-domains as optional since IPQ9574 doesn't have GDSCs [v8]: - Update bindings for the clock name change [v7]: - com_aux -> cfg_ahb in patch 7 [v6]: - Incorporated review comments - Resolve make dtbs_check messages - Fixed pcs_usb offset - Board dts file name changed [v5]: - Incorporated review comments - 'make dtbs_check' giving the following messages since ipq9574 doesn't have power domains. Hope this is ok /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: phy@7d000: 'power-domains' is a required property From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml /local/mnt/workspace/varada/varda-linux/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dtb: usb@8a00000: 'power-domains' is a required property From schema: /local/mnt/workspace/varada/varda-linux/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml - Move qmp phy DT node to newer specification [v4]: - Incorporated review comments - Address all 'make dtbs_check' errors [v3]: - Incorporated review comments regarding coding style [v2]: - Incorporated review comments regarding coding style, maintaining sorted order of entries and unused phy register offsets - Removed NOC clock entries from DT node (will be implemented later with interconnect support) - Fixed 'make dtbs_check' errors/warnings [v1]: https://lore.kernel.org/linux-arm-msm/5dac3aa4-8dc7-f9eb-5cf3-b361efdc9494@linaro.org/T/ Varadarajan Narayanan (5): dt-bindings: usb: dwc3: Add IPQ9574 compatible clk: qcom: gcc-ipq9574: Add USB related clocks arm64: dts: qcom: ipq9574: Add USB related nodes arm64: dts: qcom: ipq9574: Add LDO regulator node arm64: dts: qcom: ipq9574: Enable USB .../devicetree/bindings/usb/qcom,dwc3.yaml | 3 +- arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 30 ++++++ arch/arm64/boot/dts/qcom/ipq9574.dtsi | 104 +++++++++++++++++++++ drivers/clk/qcom/gcc-ipq9574.c | 37 ++++++++ include/dt-bindings/clock/qcom,ipq9574-gcc.h | 2 + 5 files changed, 175 insertions(+), 1 deletion(-)