| Message ID | 1617268396-1837-5-git-send-email-skakit@codeaurora.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add PMIC DT files for sc7280 | expand |
Same comments as '[1/5] arm64: dts: qcom: pm7325: Add PMIC peripherals for pm7325', plus another nit: '[3/5] arm64: dts: qcom: pmk8350: Add PMIC peripherals for pmk8350' has an ADC config for the die temperature of the pmr735a, hence it seems this patch should be before the 'pmk8350' one in this series. On Thu, Apr 01, 2021 at 02:43:15PM +0530, satya priya wrote: > Add temp-alarm and GPIO support for pmr735a. > > Signed-off-by: satya priya <skakit@codeaurora.org> > --- > arch/arm64/boot/dts/qcom/pmr735a.dtsi | 53 +++++++++++++++++++++++++++++++++++ > 1 file changed, 53 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/pmr735a.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/pmr735a.dtsi b/arch/arm64/boot/dts/qcom/pmr735a.dtsi > new file mode 100644 > index 0000000..07077fb > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/pmr735a.dtsi > @@ -0,0 +1,53 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +// Copyright (c) 2021, The Linux Foundation. All rights reserved. > + > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > + > +&spmi_bus { > + pmr735a: pmic@4 { > + compatible = "qcom,pmr735a", "qcom,spmi-pmic"; > + reg = <0x4 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pmr735a_temp_alarm: temp-alarm@a00 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0xa00>; > + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; > + #thermal-sensor-cells = <0>; > + }; > + > + pmr735a_gpios: gpios@8800 { > + compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio"; > + reg = <0x8800>; > + gpio-controller; > + gpio-ranges = <&pmr735a_gpios 0 0 4>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > +}; > + > +&thermal_zones { > + pmr735a_thermal: pmr735a-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + thermal-sensors = <&pmr735a_temp_alarm>; > + > + trips { > + pmr735a_trip0: trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + pmr735a_trip1: trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "critical"; > + }; > + }; > + }; > +}; > -- > QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member > of Code Aurora Forum, hosted by The Linux Foundation >
On 2021-04-03 00:56, Matthias Kaehlcke wrote: > Same comments as '[1/5] arm64: dts: qcom: pm7325: Add PMIC peripherals > for pm7325', plus another nit: > > '[3/5] arm64: dts: qcom: pmk8350: Add PMIC peripherals for pmk8350' has > an ADC config for the die temperature of the pmr735a, hence it seems > this > patch should be before the 'pmk8350' one in this series. > Okay. > On Thu, Apr 01, 2021 at 02:43:15PM +0530, satya priya wrote: >> Add temp-alarm and GPIO support for pmr735a. >> >> Signed-off-by: satya priya <skakit@codeaurora.org> >> ---
diff --git a/arch/arm64/boot/dts/qcom/pmr735a.dtsi b/arch/arm64/boot/dts/qcom/pmr735a.dtsi new file mode 100644 index 0000000..07077fb --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmr735a.dtsi @@ -0,0 +1,53 @@ +// SPDX-License-Identifier: BSD-3-Clause +// Copyright (c) 2021, The Linux Foundation. All rights reserved. + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmr735a: pmic@4 { + compatible = "qcom,pmr735a", "qcom,spmi-pmic"; + reg = <0x4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmr735a_temp_alarm: temp-alarm@a00 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0xa00>; + interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; + #thermal-sensor-cells = <0>; + }; + + pmr735a_gpios: gpios@8800 { + compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio"; + reg = <0x8800>; + gpio-controller; + gpio-ranges = <&pmr735a_gpios 0 0 4>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; + +&thermal_zones { + pmr735a_thermal: pmr735a-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + thermal-sensors = <&pmr735a_temp_alarm>; + + trips { + pmr735a_trip0: trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + pmr735a_trip1: trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; +};
Add temp-alarm and GPIO support for pmr735a. Signed-off-by: satya priya <skakit@codeaurora.org> --- arch/arm64/boot/dts/qcom/pmr735a.dtsi | 53 +++++++++++++++++++++++++++++++++++ 1 file changed, 53 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pmr735a.dtsi