diff mbox series

[v17,4/5] usb: dwc3: qcom: Configure wakeup interrupts during suspend

Message ID 1653387228-28110-5-git-send-email-quic_kriskura@quicinc.com
State New
Headers show
Series USB DWC3 host wake up support from system suspend | expand

Commit Message

Krishna Kurapati May 24, 2022, 10:13 a.m. UTC 
From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>

Configure DP/DM line interrupts based on the USB2 device attached to
the root hub port. When HS/FS device is connected, configure the DP line
as falling edge to detect both disconnect and remote wakeup scenarios. When
LS device is connected, configure DM line as falling edge to detect both
disconnect and remote wakeup. When no device is connected, configure both
DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
---
 drivers/usb/dwc3/dwc3-qcom.c | 74 ++++++++++++++++++++++++++++++++++++++------
 1 file changed, 65 insertions(+), 9 deletions(-)
diff mbox series

Patch

diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
index 7352124..5d5db62 100644
--- a/drivers/usb/dwc3/dwc3-qcom.c
+++ b/drivers/usb/dwc3/dwc3-qcom.c
@@ -20,7 +20,8 @@ 
 #include <linux/usb/of.h>
 #include <linux/reset.h>
 #include <linux/iopoll.h>
-
+#include <linux/usb/hcd.h>
+#include <linux/usb.h>
 #include "core.h"
 
 /* USB QSCRATCH Hardware registers */
@@ -296,11 +297,37 @@  static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
 	icc_put(qcom->icc_path_apps);
 }
 
-static void dwc3_qcom_enable_wakeup_irq(int irq)
+enum usb_device_speed dwc3_qcom_update_usb2_speed(struct dwc3_qcom *qcom)
+{
+	struct dwc3	*dwc = platform_get_drvdata(qcom->dwc3);
+	struct usb_hcd	*hcd = platform_get_drvdata(dwc->xhci);
+	struct usb_device *udev;
+	enum usb_device_speed usb2_speed;
+
+	/*
+	 * It is possible to query the speed of all children of
+	 * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code
+	 * currently supports only 1 port per controller. So
+	 * this is sufficient.
+	 */
+	udev = usb_hub_find_child(hcd->self.root_hub, 1);
+
+	if (udev)
+		usb2_speed = udev->speed;
+	else
+		usb2_speed = USB_SPEED_UNKNOWN;
+
+	return usb2_speed;
+}
+
+static void dwc3_qcom_enable_wakeup_irq(int irq, unsigned int polarity)
 {
 	if (!irq)
 		return;
 
+	if (polarity)
+		irq_set_irq_type(irq, polarity);
+
 	enable_irq(irq);
 	enable_irq_wake(irq);
 }
@@ -316,24 +343,53 @@  static void dwc3_qcom_disable_wakeup_irq(int irq)
 
 static void dwc3_qcom_disable_interrupts(struct dwc3_qcom *qcom)
 {
-	dwc3_qcom_disable_wakeup_irq(qcom->hs_phy_irq);
+	enum usb_device_speed usb2_speed = dwc3_qcom_update_usb2_speed(qcom);
 
-	dwc3_qcom_disable_wakeup_irq(qcom->dp_hs_phy_irq);
+	dwc3_qcom_disable_wakeup_irq(qcom->hs_phy_irq);
 
-	dwc3_qcom_disable_wakeup_irq(qcom->dm_hs_phy_irq);
+	if (usb2_speed == USB_SPEED_LOW) {
+		dwc3_qcom_disable_wakeup_irq(qcom->dm_hs_phy_irq);
+	} else if ((usb2_speed == USB_SPEED_HIGH) ||
+				(usb2_speed == USB_SPEED_FULL)) {
+		dwc3_qcom_disable_wakeup_irq(qcom->dp_hs_phy_irq);
+	} else {
+		dwc3_qcom_disable_wakeup_irq(qcom->dp_hs_phy_irq);
+		dwc3_qcom_disable_wakeup_irq(qcom->dm_hs_phy_irq);
+	}
 
 	dwc3_qcom_disable_wakeup_irq(qcom->ss_phy_irq);
 }
 
 static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
 {
-	dwc3_qcom_enable_wakeup_irq(qcom->hs_phy_irq);
+	enum usb_device_speed usb2_speed = dwc3_qcom_update_usb2_speed(qcom);
 
-	dwc3_qcom_enable_wakeup_irq(qcom->dp_hs_phy_irq);
+	dwc3_qcom_enable_wakeup_irq(qcom->hs_phy_irq, 0);
 
-	dwc3_qcom_enable_wakeup_irq(qcom->dm_hs_phy_irq);
+	/*
+	 * Configure DP/DM line interrupts based on the USB2 device attached to
+	 * the root hub port. When HS/FS device is connected, configure the DP line
+	 * as falling edge to detect both disconnect and remote wakeup scenarios. When
+	 * LS device is connected, configure DM line as falling edge to detect both
+	 * disconnect and remote wakeup. When no device is connected, configure both
+	 * DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
+	 */
+
+	if (usb2_speed == USB_SPEED_LOW) {
+		dwc3_qcom_enable_wakeup_irq(qcom->dm_hs_phy_irq,
+						IRQ_TYPE_EDGE_FALLING);
+	} else if ((usb2_speed == USB_SPEED_HIGH) ||
+				(usb2_speed == USB_SPEED_FULL)) {
+		dwc3_qcom_enable_wakeup_irq(qcom->dp_hs_phy_irq,
+						IRQ_TYPE_EDGE_FALLING);
+	} else {
+		dwc3_qcom_enable_wakeup_irq(qcom->dp_hs_phy_irq,
+						IRQ_TYPE_EDGE_RISING);
+		dwc3_qcom_enable_wakeup_irq(qcom->dm_hs_phy_irq,
+						IRQ_TYPE_EDGE_RISING);
+	}
 
-	dwc3_qcom_enable_wakeup_irq(qcom->ss_phy_irq);
+	dwc3_qcom_enable_wakeup_irq(qcom->ss_phy_irq, 0);
 }
 
 static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)