diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 76d7a9e80f04..dd77c7dfa310 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -947,6 +947,130 @@ static const struct qmp_phy_init_tbl qmp_v3_usb3_tx_tbl[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x06),
 };
 
+static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_rbr[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x37),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_ENABLE1, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x69),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x6f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_CTRL, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_hbr[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x37),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_ENABLE1, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x69),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_CTRL, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_hbr2[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x37),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_ENABLE1, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x8c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_CTRL, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+};
+
+static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_hbr3[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x37),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_ENABLE1, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_BUF_ENABLE, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x69),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x2a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_CTRL, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+};
+
 static const struct qmp_phy_init_tbl qmp_v3_usb3_rx_tbl[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
 	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
@@ -1798,6 +1922,11 @@ struct qmp_phy_cfg {
 	bool no_pcs_sw_reset;
 };
 
+struct qmp_phy_combo_cfg {
+	const struct qmp_phy_cfg *usb_cfg;
+	const struct qmp_phy_cfg *dp_cfg;
+};
+
 /**
  * struct qmp_phy - per-lane phy descriptor
  *
@@ -1831,6 +1960,15 @@ struct qmp_phy {
 	struct qcom_qmp *qmp;
 	struct reset_control *lane_rst;
 	enum phy_mode mode;
+	unsigned int dp_aux_cfg;
+	struct phy_configure_opts_dp dp_opts;
+	struct qmp_phy_dp_clks *dp_clks;
+};
+
+struct qmp_phy_dp_clks {
+	struct qmp_phy *qphy;
+	struct clk_hw dp_link_hw;
+	struct clk_hw dp_pixel_hw;
 };
 
 /**
@@ -2475,6 +2613,329 @@ static void qcom_qmp_phy_configure(void __iomem *base,
 	qcom_qmp_phy_configure_lane(base, regs, tbl, num, 0xff);
 }
 
+static int qcom_qmp_phy_serdes_init(struct qmp_phy *qphy)
+{
+	struct qcom_qmp *qmp = qphy->qmp;
+	const struct qmp_phy_cfg *cfg = qphy->cfg;
+	void __iomem *serdes = qphy->serdes;
+	const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts;
+	const struct qmp_phy_init_tbl *serdes_tbl;
+	int serdes_tbl_num;
+	int ret;
+
+	if (cfg->type == PHY_TYPE_DP) {
+		switch (dp_opts->link_rate) {
+		case 1620:
+			serdes_tbl = qmp_v3_dp_serdes_tbl_rbr;
+			serdes_tbl_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_rbr);
+			break;
+		case 2700:
+			serdes_tbl = qmp_v3_dp_serdes_tbl_hbr;
+			serdes_tbl_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_hbr);
+			break;
+		case 5400:
+			serdes_tbl = qmp_v3_dp_serdes_tbl_hbr2;
+			serdes_tbl_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_hbr2);
+			break;
+		case 8100:
+			serdes_tbl = qmp_v3_dp_serdes_tbl_hbr3;
+			serdes_tbl_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_hbr3);
+			break;
+		default:
+			/* Other link rates aren't supported */
+			return -EINVAL;
+		}
+	} else {
+		serdes_tbl = cfg->serdes_tbl;
+		serdes_tbl_num = cfg->serdes_tbl_num;
+	}
+
+	qcom_qmp_phy_configure(serdes, cfg->regs, serdes_tbl, serdes_tbl_num);
+
+	if (cfg->has_phy_com_ctrl) {
+		void __iomem *status;
+		unsigned int mask, val;
+
+		qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
+		qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
+			     SERDES_START | PCS_START);
+
+		status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS];
+		mask = cfg->mask_com_pcs_ready;
+
+		ret = readl_poll_timeout(status, val, (val & mask), 10,
+					 PHY_INIT_COMPLETE_TIMEOUT);
+		if (ret) {
+			dev_err(qmp->dev,
+				"phy common block init timed-out\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static void qcom_qmp_phy_dp_aux_init(struct qmp_phy *qphy)
+{
+	writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
+	       DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
+	       qphy->pcs + QSERDES_V3_DP_PHY_PD_CTL);
+
+	/* Turn on BIAS current for PHY/PLL */
+	writel(QSERDES_V3_COM_BIAS_EN | QSERDES_V3_COM_BIAS_EN_MUX |
+	       QSERDES_V3_COM_CLKBUF_L_EN | QSERDES_V3_COM_EN_SYSCLK_TX_SEL,
+	       qphy->serdes + QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN);
+
+	writel(DP_PHY_PD_CTL_PSR_PWRDN, qphy->pcs + QSERDES_V3_DP_PHY_PD_CTL);
+
+	/* Make sure that hardware is done with  PSR power down */
+	wmb();
+	writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
+	       DP_PHY_PD_CTL_LANE_0_1_PWRDN |
+	       DP_PHY_PD_CTL_LANE_2_3_PWRDN | DP_PHY_PD_CTL_PLL_PWRDN |
+	       DP_PHY_PD_CTL_DP_CLAMP_EN,
+	       qphy->pcs + QSERDES_V3_DP_PHY_PD_CTL);
+
+	writel(QSERDES_V3_COM_BIAS_EN |
+	       QSERDES_V3_COM_BIAS_EN_MUX | QSERDES_V3_COM_CLKBUF_R_EN |
+	       QSERDES_V3_COM_CLKBUF_L_EN | QSERDES_V3_COM_EN_SYSCLK_TX_SEL |
+	       QSERDES_V3_COM_CLKBUF_RX_DRIVE_L,
+	       qphy->serdes + QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN);
+
+	writel(0x00, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG0);
+	writel(0x13, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG1);
+	writel(0x24, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG2);
+	writel(0x00, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG3);
+	writel(0x0a, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG4);
+	writel(0x26, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG5);
+	writel(0x0a, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG6);
+	writel(0x03, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG7);
+	writel(0xbb, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG8);
+	writel(0x03, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG9);
+	qphy->dp_aux_cfg = 0;
+
+	writel(PHY_AUX_STOP_ERR_MASK | PHY_AUX_DEC_ERR_MASK |
+	       PHY_AUX_SYNC_ERR_MASK | PHY_AUX_ALIGN_ERR_MASK |
+	       PHY_AUX_REQ_ERR_MASK,
+	       qphy->pcs + QSERDES_V3_DP_PHY_AUX_INTERRUPT_MASK);
+}
+
+static const u8 vm_pre_emphasis[4][4] = {
+	{ 0x00, 0x0b, 0x12, 0xff },       /* pe0, 0 db */
+	{ 0x00, 0x0a, 0x12, 0xff },       /* pe1, 3.5 db */
+	{ 0x00, 0x0c, 0xff, 0xff },       /* pe2, 6.0 db */
+	{ 0xff, 0xff, 0xff, 0xff }        /* pe3, 9.5 db */
+};
+
+/* voltage swing, 0.2v and 1.0v are not support */
+static const u8 vm_voltage_swing[4][4] = {
+	{ 0x07, 0x0f, 0x14, 0xff }, /* sw0, 0.4v  */
+	{ 0x11, 0x1d, 0x1f, 0xff }, /* sw1, 0.6 v */
+	{ 0x18, 0x1f, 0xff, 0xff }, /* sw1, 0.8 v */
+	{ 0xff, 0xff, 0xff, 0xff }  /* sw1, 1.2 v, optional */
+};
+
+static const u8 vm_pre_emphasis_hbr3_hbr2[4][4] = {
+	{ 0x00, 0x0c, 0x15, 0x1a },
+	{ 0x02, 0x0e, 0x16, 0xff },
+	{ 0x02, 0x11, 0xff, 0xff },
+	{ 0x04, 0xff, 0xff, 0xff }
+};
+
+static const u8 vm_voltage_swing_hbr3_hbr2[4][4] = {
+	{ 0x02, 0x12, 0x16, 0x1a },
+	{ 0x09, 0x19, 0x1f, 0xff },
+	{ 0x10, 0x1f, 0xff, 0xff },
+	{ 0x1f, 0xff, 0xff, 0xff }
+};
+
+static const u8 vm_pre_emphasis_hbr_rbr[4][4] = {
+	{ 0x00, 0x0c, 0x14, 0x19 },
+	{ 0x00, 0x0b, 0x12, 0xff },
+	{ 0x00, 0x0b, 0xff, 0xff },
+	{ 0x04, 0xff, 0xff, 0xff }
+};
+
+static const u8 vm_voltage_swing_hbr_rbr[4][4] = {
+	{ 0x08, 0x0f, 0x16, 0x1f },
+	{ 0x11, 0x1e, 0x1f, 0xff },
+	{ 0x19, 0x1f, 0xff, 0xff },
+	{ 0x1f, 0xff, 0xff, 0xff }
+};
+
+static void qcom_qmp_phy_configure_dp_tx(struct qmp_phy *qphy)
+{
+	const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts;
+	unsigned int v_level = 0, p_level = 0;
+	u32 bias_en, drvr_en;
+	u8 voltage_swing_cfg, pre_emphasis_cfg;
+	int i;
+
+	for (i = 0; i < dp_opts->lanes; i++) {
+		v_level = max(v_level, dp_opts->voltage[i]);
+		p_level = max(p_level, dp_opts->pre[i]);
+	}
+
+	if (dp_opts->lanes == 1) {
+		bias_en = 0x3e;
+		drvr_en = 0x13;
+	} else {
+		bias_en = 0x3f;
+		drvr_en = 0x10;
+	}
+
+	/* TODO: Pick based on link rate */
+	voltage_swing_cfg = vm_voltage_swing_hbr_rbr[v_level][p_level];
+	pre_emphasis_cfg = vm_pre_emphasis_hbr_rbr[v_level][p_level];
+
+	/* TODO: Move check to config check */
+	if (voltage_swing_cfg == 0xFF && pre_emphasis_cfg == 0xFF)
+		return;
+
+	/* Enable MUX to use Cursor values from these registers */
+	voltage_swing_cfg |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN;
+	pre_emphasis_cfg |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN;
+
+	writel(voltage_swing_cfg, qphy->tx + QSERDES_V3_TX_TX_DRV_LVL);
+	writel(pre_emphasis_cfg, qphy->tx + QSERDES_V3_TX_TX_EMP_POST1_LVL);
+	writel(voltage_swing_cfg, qphy->tx2 + QSERDES_V3_TX_TX_DRV_LVL);
+	writel(pre_emphasis_cfg, qphy->tx2 + QSERDES_V3_TX_TX_EMP_POST1_LVL);
+
+	writel(drvr_en, qphy->tx + QSERDES_V3_TX_HIGHZ_DRVR_EN);
+	writel(bias_en, qphy->tx + QSERDES_V3_TX_TRANSCEIVER_BIAS_EN);
+	writel(drvr_en, qphy->tx2 + QSERDES_V3_TX_HIGHZ_DRVR_EN);
+	writel(bias_en, qphy->tx2 + QSERDES_V3_TX_TRANSCEIVER_BIAS_EN);
+}
+
+static int qcom_qmp_dp_phy_configure(struct phy *phy, union phy_configure_opts *opts)
+{
+	const struct phy_configure_opts_dp *dp_opts = &opts->dp;
+	struct qmp_phy *qphy = phy_get_drvdata(phy);
+
+	memcpy(&qphy->dp_opts, dp_opts, sizeof(*dp_opts));
+	if (qphy->dp_opts.set_voltages) {
+		qcom_qmp_phy_configure_dp_tx(qphy);
+		qphy->dp_opts.set_voltages = 0;
+	}
+
+	return 0;
+}
+
+static int qcom_qmp_phy_configure_dp_phy(struct qmp_phy *qphy)
+{
+	const struct qmp_phy_dp_clks *dp_clks = qphy->dp_clks;
+	const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts;
+	u32 val, phy_vco_div, status;
+	unsigned long pixel_freq;
+
+	val = DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
+	      DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN;
+
+	/*
+	if (lane_cnt == 4 || orientation == ORIENTATION_CC2)
+		val |= DP_PHY_PD_CTL_LANE_0_1_PWRDN;
+	if (lane_cnt == 4 || orientation == ORIENTATION_CC1)
+		val |= DP_PHY_PD_CTL_LANE_2_3_PWRDN;
+	*/
+	/*
+	 * TODO: Assume orientation is CC1 for now and two lanes, need to
+	 * use type-c connector to understand orientation and lanes
+	 */
+	val |= DP_PHY_PD_CTL_LANE_2_3_PWRDN;
+
+	writel(val, qphy->pcs + QSERDES_V3_DP_PHY_PD_CTL);
+
+	/*
+	if (orientation == ORIENTATION_CC2)
+		writel(0x4c, qphy->pcs + QSERDES_V3_DP_PHY_MODE);
+	else
+	*/
+	/* does this do anything? link_clock_sel_mux isn't set (bit 5) */
+	writel(0x5c, qphy->pcs + QSERDES_V3_DP_PHY_MODE);
+
+	writel(0x05, qphy->pcs + QSERDES_V3_DP_PHY_TX0_TX1_LANE_CTL);
+	writel(0x05, qphy->pcs + QSERDES_V3_DP_PHY_TX2_TX3_LANE_CTL);
+
+	switch (dp_opts->link_rate) {
+	case 1620:
+		phy_vco_div = 0x1;
+		pixel_freq = 1620000000UL / 2;
+		break;
+	case 2700:
+		phy_vco_div = 0x1;
+		pixel_freq = 2700000000UL / 2;
+		break;
+	case 5400:
+		phy_vco_div = 0x2;
+		pixel_freq = 5400000000UL / 4;
+		break;
+	case 8100:
+		phy_vco_div = 0x0;
+		pixel_freq = 8100000000UL / 6;
+		break;
+	default:
+		/* Other link rates aren't supported */
+		return -EINVAL;
+	}
+	writel(phy_vco_div, qphy->pcs + QSERDES_V3_DP_PHY_VCO_DIV);
+
+	clk_set_rate(dp_clks->dp_link_hw.clk, dp_opts->link_rate * 100000);
+	clk_set_rate(dp_clks->dp_pixel_hw.clk, pixel_freq);
+
+	writel(0x04, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG2);
+	writel(0x01, qphy->pcs + QSERDES_V3_DP_PHY_CFG);
+	writel(0x05, qphy->pcs + QSERDES_V3_DP_PHY_CFG);
+	writel(0x01, qphy->pcs + QSERDES_V3_DP_PHY_CFG);
+	writel(0x09, qphy->pcs + QSERDES_V3_DP_PHY_CFG);
+
+	writel(0x20, qphy->serdes + QSERDES_COM_RESETSM_CNTRL);
+
+	if (readl_poll_timeout(qphy->serdes + QSERDES_V3_COM_C_READY_STATUS,
+			status,
+			((status & BIT(0)) > 0),
+			500,
+			10000))
+		return -ETIMEDOUT;
+
+	writel(0x19, qphy->pcs + QSERDES_V3_DP_PHY_CFG);
+
+	if (readl_poll_timeout(qphy->pcs + QSERDES_V3_DP_PHY_STATUS,
+			status,
+			((status & BIT(1)) > 0),
+			500,
+			10000))
+		return -ETIMEDOUT;
+
+	writel(0x18, qphy->pcs + QSERDES_V3_DP_PHY_CFG);
+	udelay(2000);
+	writel(0x19, qphy->pcs + QSERDES_V3_DP_PHY_CFG);
+
+	return readl_poll_timeout(qphy->pcs + QSERDES_V3_DP_PHY_STATUS,
+			status,
+			((status & BIT(1)) > 0),
+			500,
+			10000);
+}
+
+/*
+ * We need to calibrate the aux setting here as many times
+ * as the caller tries
+ */
+static int qcom_qmp_dp_phy_calibrate(struct phy *phy)
+{
+	struct qmp_phy *qphy = phy_get_drvdata(phy);
+	const u8 cfg1_settings[] = { 0x13, 0x23, 0x1d };
+	u8 val;
+
+	qphy->dp_aux_cfg++;
+	qphy->dp_aux_cfg %= ARRAY_SIZE(cfg1_settings);
+	val = cfg1_settings[qphy->dp_aux_cfg];
+
+	writel(val, qphy->pcs + QSERDES_V3_DP_PHY_AUX_CFG1);
+
+	return 0;
+}
+
 static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 {
 	struct qcom_qmp *qmp = qphy->qmp;
@@ -2529,6 +2990,9 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 			     SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
 			     SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
 
+		/* Default type-c orientation, i.e CC1 */
+		qphy_setbits(dp_com, QPHY_V3_DP_COM_TYPEC_CTRL, 0x02);
+
 		qphy_setbits(dp_com, QPHY_V3_DP_COM_PHY_MODE_CTRL,
 			     USB3_MODE | DP_MODE);
 
@@ -2536,6 +3000,9 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 		qphy_clrbits(dp_com, QPHY_V3_DP_COM_RESET_OVRD_CTRL,
 			     SW_DPPHY_RESET_MUX | SW_DPPHY_RESET |
 			     SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
+
+		qphy_clrbits(dp_com, QPHY_V3_DP_COM_SWI_CTRL, 0x03);
+		qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
 	}
 
 	if (cfg->has_phy_com_ctrl) {
@@ -2551,36 +3018,10 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 					cfg->pwrdn_ctrl);
 	}
 
-	/* Serdes configuration */
-	qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
-			       cfg->serdes_tbl_num);
-
-	if (cfg->has_phy_com_ctrl) {
-		void __iomem *status;
-		unsigned int mask, val;
-
-		qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET], SW_RESET);
-		qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
-			     SERDES_START | PCS_START);
-
-		status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS];
-		mask = cfg->mask_com_pcs_ready;
-
-		ret = readl_poll_timeout(status, val, (val & mask), 10,
-					 PHY_INIT_COMPLETE_TIMEOUT);
-		if (ret) {
-			dev_err(qmp->dev,
-				"phy common block init timed-out\n");
-			goto err_com_init;
-		}
-	}
-
 	mutex_unlock(&qmp->phy_mutex);
 
 	return 0;
 
-err_com_init:
-	clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks);
 err_rst:
 	while (++i < cfg->num_resets)
 		reset_control_assert(qmp->resets[i]);
@@ -2627,20 +3068,12 @@ static int qcom_qmp_phy_com_exit(struct qmp_phy *qphy)
 	return 0;
 }
 
-static int qcom_qmp_phy_enable(struct phy *phy)
+static int qcom_qmp_phy_init(struct phy *phy)
 {
 	struct qmp_phy *qphy = phy_get_drvdata(phy);
 	struct qcom_qmp *qmp = qphy->qmp;
 	const struct qmp_phy_cfg *cfg = qphy->cfg;
-	void __iomem *tx = qphy->tx;
-	void __iomem *rx = qphy->rx;
-	void __iomem *pcs = qphy->pcs;
-	void __iomem *pcs_misc = qphy->pcs_misc;
-	void __iomem *dp_com = qmp->dp_com;
-	void __iomem *status;
-	unsigned int mask, val, ready;
 	int ret;
-
 	dev_vdbg(qmp->dev, "Initializing QMP phy\n");
 
 	if (cfg->no_pcs_sw_reset) {
@@ -2667,13 +3100,34 @@ static int qcom_qmp_phy_enable(struct phy *phy)
 
 		ret = reset_control_assert(qmp->ufs_reset);
 		if (ret)
-			goto err_lane_rst;
+			return ret;
 	}
 
 	ret = qcom_qmp_phy_com_init(qphy);
 	if (ret)
 		return ret;
 
+	if (cfg->type == PHY_TYPE_DP)
+		qcom_qmp_phy_dp_aux_init(qphy);
+
+	return 0;
+}
+
+static int qcom_qmp_phy_power_on(struct phy *phy)
+{
+	struct qmp_phy *qphy = phy_get_drvdata(phy);
+	struct qcom_qmp *qmp = qphy->qmp;
+	const struct qmp_phy_cfg *cfg = qphy->cfg;
+	void __iomem *tx = qphy->tx;
+	void __iomem *rx = qphy->rx;
+	void __iomem *pcs = qphy->pcs;
+	void __iomem *pcs_misc = qphy->pcs_misc;
+	void __iomem *status;
+	unsigned int mask, val, ready;
+	int ret;
+
+	qcom_qmp_phy_serdes_init(qphy);
+
 	if (cfg->has_lane_rst) {
 		ret = reset_control_deassert(qphy->lane_rst);
 		if (ret) {
@@ -2697,13 +3151,24 @@ static int qcom_qmp_phy_enable(struct phy *phy)
 		qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs,
 					    cfg->tx_tbl, cfg->tx_tbl_num, 2);
 
+	/* Configure special DP tx tunings */
+	if (cfg->type == PHY_TYPE_DP)
+		qcom_qmp_phy_configure_dp_tx(qphy);
+
 	qcom_qmp_phy_configure_lane(rx, cfg->regs,
 				    cfg->rx_tbl, cfg->rx_tbl_num, 1);
+
 	if (cfg->is_dual_lane_phy)
 		qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs,
 					    cfg->rx_tbl, cfg->rx_tbl_num, 2);
 
-	qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+	/* Configure link rate, swing, etc. */
+	if (cfg->type == PHY_TYPE_DP) {
+		qcom_qmp_phy_configure_dp_phy(qphy);
+	} else {
+		qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+	}
+
 	ret = reset_control_deassert(qmp->ufs_reset);
 	if (ret)
 		goto err_lane_rst;
@@ -2721,69 +3186,77 @@ static int qcom_qmp_phy_enable(struct phy *phy)
 	if (cfg->has_pwrdn_delay)
 		usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);
 
-	/* Pull PHY out of reset state */
-	if (!cfg->no_pcs_sw_reset)
-		qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
-
-	if (cfg->has_phy_dp_com_ctrl)
-		qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
-
-	/* start SerDes and Phy-Coding-Sublayer */
-	qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
-
-	if (cfg->type == PHY_TYPE_UFS) {
-		status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
-		mask = PCS_READY;
-		ready = PCS_READY;
-	} else {
-		status = pcs + cfg->regs[QPHY_PCS_STATUS];
-		mask = PHYSTATUS;
-		ready = 0;
-	}
+	if (cfg->type != PHY_TYPE_DP) {
+		/* Pull PHY out of reset state */
+		if (!cfg->no_pcs_sw_reset)
+			qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+		/* start SerDes and Phy-Coding-Sublayer */
+		qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+
+		if (cfg->type == PHY_TYPE_UFS) {
+			status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
+			mask = PCS_READY;
+			ready = PCS_READY;
+		} else {
+			status = pcs + cfg->regs[QPHY_PCS_STATUS];
+			mask = PHYSTATUS;
+			ready = 0;
+		}
 
-	ret = readl_poll_timeout(status, val, (val & mask) == ready, 10,
-				 PHY_INIT_COMPLETE_TIMEOUT);
-	if (ret) {
-		dev_err(qmp->dev, "phy initialization timed-out\n");
-		goto err_pcs_ready;
+		ret = readl_poll_timeout(status, val, (val & mask) == ready, 10,
+					 PHY_INIT_COMPLETE_TIMEOUT);
+		if (ret) {
+			dev_err(qmp->dev, "phy initialization timed-out\n");
+			goto err_pcs_ready;
+		}
 	}
 	return 0;
 
 err_pcs_ready:
-	reset_control_assert(qmp->ufs_reset);
 	clk_disable_unprepare(qphy->pipe_clk);
 err_clk_enable:
 	if (cfg->has_lane_rst)
 		reset_control_assert(qphy->lane_rst);
 err_lane_rst:
-	qcom_qmp_phy_com_exit(qphy);
-
 	return ret;
 }
 
-static int qcom_qmp_phy_disable(struct phy *phy)
+static int qcom_qmp_phy_power_off(struct phy *phy)
 {
 	struct qmp_phy *qphy = phy_get_drvdata(phy);
 	const struct qmp_phy_cfg *cfg = qphy->cfg;
 
 	clk_disable_unprepare(qphy->pipe_clk);
 
-	/* PHY reset */
-	if (!cfg->no_pcs_sw_reset)
-		qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+	if (cfg->type == PHY_TYPE_DP) {
+		/* Assert DP PHY power down */
+		writel(DP_PHY_PD_CTL_PSR_PWRDN, qphy->pcs + QSERDES_V3_DP_PHY_PD_CTL);
+	} else {
+		/* PHY reset */
+		if (!cfg->no_pcs_sw_reset)
+			qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
 
-	/* stop SerDes and Phy-Coding-Sublayer */
-	qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+		/* stop SerDes and Phy-Coding-Sublayer */
+		qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
 
-	/* Put PHY into POWER DOWN state: active low */
-	if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL]) {
-		qphy_clrbits(qphy->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
-			     cfg->pwrdn_ctrl);
-	} else {
-		qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL,
-				cfg->pwrdn_ctrl);
+		/* Put PHY into POWER DOWN state: active low */
+		if (cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL]) {
+			qphy_clrbits(qphy->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
+				     cfg->pwrdn_ctrl);
+		} else {
+			qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL,
+					cfg->pwrdn_ctrl);
+		}
 	}
 
+	return 0;
+}
+
+static int qcom_qmp_phy_exit(struct phy *phy)
+{
+	struct qmp_phy *qphy = phy_get_drvdata(phy);
+	const struct qmp_phy_cfg *cfg = qphy->cfg;
+
 	if (cfg->has_lane_rst)
 		reset_control_assert(qphy->lane_rst);
 
@@ -2792,6 +3265,31 @@ static int qcom_qmp_phy_disable(struct phy *phy)
 	return 0;
 }
 
+static int qcom_qmp_phy_enable(struct phy *phy)
+{
+	int ret;
+
+	ret = qcom_qmp_phy_init(phy);
+	if (ret)
+		return ret;
+
+	ret = qcom_qmp_phy_power_on(phy);
+	if (ret)
+		qcom_qmp_phy_exit(phy);
+
+	return ret;
+}
+
+static int qcom_qmp_phy_disable(struct phy *phy)
+{
+	int ret;
+
+	ret = qcom_qmp_phy_power_off(phy);
+	if (ret)
+		return ret;
+	return qcom_qmp_phy_exit(phy);
+}
+
 static int qcom_qmp_phy_set_mode(struct phy *phy,
 				 enum phy_mode mode, int submode)
 {
@@ -2857,7 +3355,7 @@ static int __maybe_unused qcom_qmp_phy_runtime_suspend(struct device *dev)
 
 	dev_vdbg(dev, "Suspending QMP phy, mode:%d\n", qphy->mode);
 
-	/* Supported only for USB3 PHY */
+	/* Supported only for USB3 PHY and luckily USB3 is the first phy */
 	if (cfg->type != PHY_TYPE_USB3)
 		return 0;
 
@@ -2883,7 +3381,7 @@ static int __maybe_unused qcom_qmp_phy_runtime_resume(struct device *dev)
 
 	dev_vdbg(dev, "Resuming QMP phy, mode:%d\n", qphy->mode);
 
-	/* Supported only for USB3 PHY */
+	/* Supported only for USB3 PHY and luckily USB3 is the first phy */
 	if (cfg->type != PHY_TYPE_USB3)
 		return 0;
 
@@ -2967,7 +3465,7 @@ static int qcom_qmp_phy_clk_init(struct device *dev, const struct qmp_phy_cfg *c
 	return devm_clk_bulk_get(dev, num, qmp->clks);
 }
 
-static void phy_pipe_clk_release_provider(void *res)
+static void phy_clk_release_provider(void *res)
 {
 	of_clk_del_provider(res);
 }
@@ -3024,9 +3522,202 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
 	 * Roll a devm action because the clock provider is the child node, but
 	 * the child node is not actually a device.
 	 */
-	ret = devm_add_action(qmp->dev, phy_pipe_clk_release_provider, np);
+	ret = devm_add_action(qmp->dev, phy_clk_release_provider, np);
 	if (ret)
-		phy_pipe_clk_release_provider(np);
+		phy_clk_release_provider(np);
+
+	return ret;
+}
+
+/*
+ * Display Port PLL driver block diagram for branch clocks
+ *
+ *              +------------------------------+
+ *              |         DP_VCO_CLK           |
+ *              |                              |
+ *              |    +-------------------+     |
+ *              |    |   (DP PLL/VCO)    |     |
+ *              |    +---------+---------+     |
+ *              |              v               |
+ *              |   +----------+-----------+   |
+ *              |   | hsclk_divsel_clk_src |   |
+ *              |   +----------+-----------+   |
+ *              +------------------------------+
+ *                              |
+ *          +---------<---------v------------>----------+
+ *          |                                           |
+ * +--------v----------------+                          |
+ * |    dp_phy_pll_link_clk  |                          |
+ * |     link_clk            |                          |
+ * +--------+----------------+                          |
+ *          |                                           |
+ *          |                                           |
+ *          v                                           v
+ * Input to DISPCC block                                |
+ * for link clk, crypto clk                             |
+ * and interface clock                                  |
+ *                                                      |
+ *                                                      |
+ *      +--------<------------+-----------------+---<---+
+ *      |                     |                 |
+ * +----v---------+  +--------v-----+  +--------v------+
+ * | vco_divided  |  | vco_divided  |  | vco_divided   |
+ * |    _clk_src  |  |    _clk_src  |  |    _clk_src   |
+ * |              |  |              |  |               |
+ * |divsel_six    |  |  divsel_two  |  |  divsel_four  |
+ * +-------+------+  +-----+--------+  +--------+------+
+ *         |                 |                  |
+ *         v---->----------v-------------<------v
+ *                         |
+ *              +----------+-----------------+
+ *              |   dp_phy_pll_vco_div_clk   |
+ *              +---------+------------------+
+ *                        |
+ *                        v
+ *              Input to DISPCC block
+ *              for DP pixel clock
+ *
+ */
+static int qcom_qmp_dp_pixel_clk_determine_rate(struct clk_hw *hw,
+						struct clk_rate_request *req)
+{
+	switch (req->rate) {
+	case 1620000000UL / 2:
+	case 2700000000UL / 2:
+	/* 5.4 and 8.1 GHz are same link rate as 2.7GHz, i.e. div 4 and div 6 */
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static unsigned long
+qcom_qmp_dp_pixel_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+	const struct qmp_phy_dp_clks *dp_clks;
+	const struct qmp_phy *qphy;
+	const struct phy_configure_opts_dp *dp_opts;
+
+	dp_clks = container_of(hw, struct qmp_phy_dp_clks, dp_pixel_hw);
+	qphy = dp_clks->qphy;
+	dp_opts = &qphy->dp_opts;
+
+	switch (dp_opts->link_rate) {
+	case 1620:
+		return 1620000000UL / 2;
+	case 2700:
+		return 2700000000UL / 2;
+	case 5400:
+		return 5400000000UL / 4;
+	case 8100:
+		return 8100000000UL / 6;
+	default:
+		return 0;
+	}
+}
+
+static const struct clk_ops qcom_qmp_dp_pixel_clk_ops = {
+	.determine_rate = qcom_qmp_dp_pixel_clk_determine_rate,
+	.recalc_rate = qcom_qmp_dp_pixel_clk_recalc_rate,
+};
+
+static int qcom_qmp_dp_link_clk_determine_rate(struct clk_hw *hw,
+					       struct clk_rate_request *req)
+{
+	switch (req->rate) {
+	case 162000000:
+	case 270000000:
+	case 540000000:
+	case 810000000:
+		return 0;
+	default:
+		return -EINVAL;
+	}
+}
+
+static unsigned long
+qcom_qmp_dp_link_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+	const struct qmp_phy_dp_clks *dp_clks;
+	const struct qmp_phy *qphy;
+	const struct phy_configure_opts_dp *dp_opts;
+
+	dp_clks = container_of(hw, struct qmp_phy_dp_clks, dp_link_hw);
+	qphy = dp_clks->qphy;
+	dp_opts = &qphy->dp_opts;
+
+	switch (dp_opts->link_rate) {
+	case 1620:
+	case 2700:
+	case 5400:
+	case 8100:
+		return dp_opts->link_rate * 100000;
+	default:
+		return 0;
+	}
+}
+
+static const struct clk_ops qcom_qmp_dp_link_clk_ops = {
+	.determine_rate = qcom_qmp_dp_link_clk_determine_rate,
+	.recalc_rate = qcom_qmp_dp_link_clk_recalc_rate,
+};
+
+static struct clk_hw *
+qcom_qmp_dp_clks_hw_get(struct of_phandle_args *clkspec, void *data)
+{
+	struct qmp_phy_dp_clks *dp_clks = data;
+	unsigned int idx = clkspec->args[0];
+
+	if (idx >= 2) {
+		pr_err("%s: invalid index %u\n", __func__, idx);
+		return ERR_PTR(-EINVAL);
+	}
+
+	if (idx == 0)
+		return &dp_clks->dp_link_hw;
+
+	return &dp_clks->dp_pixel_hw;
+}
+
+static int phy_dp_clks_register(struct qcom_qmp *qmp, struct qmp_phy *qphy,
+				struct device_node *np)
+{
+	struct clk_init_data init = { };
+	struct qmp_phy_dp_clks *dp_clks;
+	int ret;
+
+	dp_clks = devm_kzalloc(qmp->dev, sizeof(*dp_clks), GFP_KERNEL);
+	if (!dp_clks)
+		return -ENOMEM;
+
+	dp_clks->qphy = qphy;
+	qphy->dp_clks = dp_clks;
+
+	init.ops = &qcom_qmp_dp_link_clk_ops;
+	init.name = "qmp_dp_phy_pll_link_clk";
+	dp_clks->dp_link_hw.init = &init;
+	ret = devm_clk_hw_register(qmp->dev, &dp_clks->dp_link_hw);
+	if (ret)
+		return ret;
+
+	init.ops = &qcom_qmp_dp_pixel_clk_ops;
+	init.name = "qmp_dp_phy_pll_vco_div_clk";
+	dp_clks->dp_pixel_hw.init = &init;
+	ret = devm_clk_hw_register(qmp->dev, &dp_clks->dp_pixel_hw);
+	if (ret)
+		return ret;
+
+	ret = of_clk_add_hw_provider(np, qcom_qmp_dp_clks_hw_get, dp_clks);
+	if (ret)
+		return ret;
+
+	/*
+	 * Roll a devm action because the clock provider is the child node, but
+	 * the child node is not actually a device.
+	 */
+	ret = devm_add_action(qmp->dev, phy_clk_release_provider, np);
+	if (ret)
+		phy_clk_release_provider(np);
 
 	return ret;
 }
@@ -3038,6 +3729,17 @@ static const struct phy_ops qcom_qmp_phy_gen_ops = {
 	.owner		= THIS_MODULE,
 };
 
+static const struct phy_ops qcom_qmp_phy_dp_ops = {
+	.init		= qcom_qmp_phy_init,
+	.configure	= qcom_qmp_dp_phy_configure,
+	.power_on	= qcom_qmp_phy_power_on,
+	.calibrate	= qcom_qmp_dp_phy_calibrate,
+	.power_off	= qcom_qmp_phy_power_off,
+	.exit		= qcom_qmp_phy_exit,
+	.set_mode	= qcom_qmp_phy_set_mode,
+	.owner		= THIS_MODULE,
+};
+
 static const struct phy_ops qcom_qmp_pcie_ufs_ops = {
 	.power_on	= qcom_qmp_phy_enable,
 	.power_off	= qcom_qmp_phy_disable,
@@ -3052,7 +3754,7 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id,
 	struct qcom_qmp *qmp = dev_get_drvdata(dev);
 	struct phy *generic_phy;
 	struct qmp_phy *qphy;
-	const struct phy_ops *ops = &qcom_qmp_phy_gen_ops;
+	const struct phy_ops *ops;
 	char prop_name[MAX_PROP_NAME];
 	int ret;
 
@@ -3143,6 +3845,10 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id,
 
 	if (cfg->type == PHY_TYPE_UFS || cfg->type == PHY_TYPE_PCIE)
 		ops = &qcom_qmp_pcie_ufs_ops;
+	else if (cfg->type == PHY_TYPE_DP)
+		ops = &qcom_qmp_phy_dp_ops;
+	else
+		ops = &qcom_qmp_phy_gen_ops;
 
 	generic_phy = devm_phy_create(dev, np, ops);
 	if (IS_ERR(generic_phy)) {
@@ -3226,6 +3932,10 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 };
 MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table);
 
+static const struct of_device_id qcom_qmp_combo_phy_of_match_table[] = {
+	{ }
+};
+
 static const struct dev_pm_ops qcom_qmp_phy_pm_ops = {
 	SET_RUNTIME_PM_OPS(qcom_qmp_phy_runtime_suspend,
 			   qcom_qmp_phy_runtime_resume, NULL)
@@ -3240,8 +3950,13 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 	struct phy_provider *phy_provider;
 	void __iomem *base;
 	void __iomem *serdes;
+	void __iomem *usb_serdes;
+	void __iomem *dp_serdes;
+	const struct qmp_phy_combo_cfg *combo_cfg = NULL;
 	const struct qmp_phy_cfg *cfg;
-	int num, id;
+	const struct qmp_phy_cfg *usb_cfg;
+	const struct qmp_phy_cfg *dp_cfg;
+	int num, id, expected_phys;
 	int ret;
 
 	qmp = devm_kzalloc(dev, sizeof(*qmp), GFP_KERNEL);
@@ -3253,8 +3968,20 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 
 	/* Get the specific init parameters of QMP phy */
 	cfg = of_device_get_match_data(dev);
-	if (!cfg)
-		return -EINVAL;
+	if (!cfg) {
+		const struct of_device_id *match;
+
+		match = of_match_device(qcom_qmp_combo_phy_of_match_table, dev);
+		if (!match)
+			return -EINVAL;
+
+		combo_cfg = match->data;
+		if (!combo_cfg)
+			return -EINVAL;
+
+		usb_cfg = combo_cfg->usb_cfg;
+		cfg = usb_cfg; /* Setup clks and regulators */
+	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	base = devm_ioremap_resource(dev, res);
@@ -3263,9 +3990,10 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 
 	/* per PHY serdes; usually located at base address */
 	serdes = base;
+	usb_serdes = base;
 
 	/* per PHY dp_com; if PHY has dp_com control block */
-	if (cfg->has_phy_dp_com_ctrl) {
+	if (combo_cfg || cfg->has_phy_dp_com_ctrl) {
 		res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 		base = devm_ioremap_resource(dev, res);
 		if (IS_ERR(base))
@@ -3274,6 +4002,20 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 		qmp->dp_com = base;
 	}
 
+	if (combo_cfg) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+		base = devm_ioremap_resource(dev, res);
+		if (IS_ERR(base))
+			return PTR_ERR(base);
+
+		/* Only two serdes for combo PHY */
+		dp_serdes = base;
+		dp_cfg = combo_cfg->dp_cfg;
+		expected_phys = 2;
+	} else {
+		expected_phys = cfg->nlanes;
+	}
+
 	mutex_init(&qmp->phy_mutex);
 
 	ret = qcom_qmp_phy_clk_init(dev, cfg);
@@ -3294,14 +4036,13 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 
 	num = of_get_available_child_count(dev->of_node);
 	/* do we have a rogue child node ? */
-	if (num > cfg->nlanes)
+	if (num > expected_phys)
 		return -EINVAL;
 
 	qmp->phys = devm_kcalloc(dev, num, sizeof(*qmp->phys), GFP_KERNEL);
 	if (!qmp->phys)
 		return -ENOMEM;
 
-	id = 0;
 	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
 	/*
@@ -3310,7 +4051,16 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 	 */
 	pm_runtime_forbid(dev);
 
+	id = 0;
 	for_each_available_child_of_node(dev->of_node, child) {
+		if (of_node_name_eq(child, "dp-phy")) {
+			cfg = dp_cfg;
+			serdes = dp_serdes;
+		} else if (of_node_name_eq(child, "usb3-phy")) {
+			cfg = usb_cfg;
+			serdes = usb_serdes;
+		}
+
 		/* Create per-lane phy */
 		ret = qcom_qmp_phy_create(dev, child, id, serdes, cfg);
 		if (ret) {
@@ -3330,6 +4080,13 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 					"failed to register pipe clock source\n");
 				goto err_node_put;
 			}
+		} else if (cfg->type == PHY_TYPE_DP) {
+			ret = phy_dp_clks_register(qmp, qmp->phys[id], child);
+			if (ret) {
+				dev_err(qmp->dev,
+					"failed to register DP clock source\n");
+				goto err_node_put;
+			}
 		}
 		id++;
 	}
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 4277f592684b..5de1f25fc166 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -135,6 +135,9 @@
 #define QPHY_V3_DP_COM_RESET_OVRD_CTRL			0x1c
 
 /* Only for QMP V3 PHY - QSERDES COM registers */
+#define QSERDES_V3_COM_ATB_SEL1				0x000
+#define QSERDES_V3_COM_ATB_SEL2				0x004
+#define QSERDES_V3_COM_FREQ_UPDATE			0x008
 #define QSERDES_V3_COM_BG_TIMER				0x00c
 #define QSERDES_V3_COM_SSC_EN_CENTER			0x010
 #define QSERDES_V3_COM_SSC_ADJ_PER1			0x014
@@ -144,6 +147,13 @@
 #define QSERDES_V3_COM_SSC_STEP_SIZE1			0x024
 #define QSERDES_V3_COM_SSC_STEP_SIZE2			0x028
 #define QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN		0x034
+# define QSERDES_V3_COM_BIAS_EN				0x0001
+# define QSERDES_V3_COM_BIAS_EN_MUX			0x0002
+# define QSERDES_V3_COM_CLKBUF_R_EN			0x0004
+# define QSERDES_V3_COM_CLKBUF_L_EN			0x0008
+# define QSERDES_V3_COM_EN_SYSCLK_TX_SEL		0x0010
+# define QSERDES_V3_COM_CLKBUF_RX_DRIVE_L		0x0020
+# define QSERDES_V3_COM_CLKBUF_RX_DRIVE_R		0x0040
 #define QSERDES_V3_COM_CLK_ENABLE1			0x038
 #define QSERDES_V3_COM_SYS_CLK_CTRL			0x03c
 #define QSERDES_V3_COM_SYSCLK_BUF_ENABLE		0x040
@@ -205,12 +215,36 @@
 #define QSERDES_V3_COM_CMN_MODE				0x184
 
 /* Only for QMP V3 PHY - TX registers */
+#define QSERDES_V3_TX_BIST_MODE_LANENO			0x000
+#define QSERDES_V3_TX_CLKBUF_ENABLE			0x008
+#define QSERDES_V3_TX_TX_EMP_POST1_LVL			0x00c
+# define DP_PHY_TXn_TX_EMP_POST1_LVL_MASK		0x001f
+# define DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN		0x0020
+
+#define QSERDES_V3_TX_TX_DRV_LVL			0x01c
+# define DP_PHY_TXn_TX_DRV_LVL_MASK			0x001f
+# define DP_PHY_TXn_TX_DRV_LVL_MUX_EN			0x0020
+
+#define QSERDES_V3_TX_RESET_TSYNC_EN			0x024
+#define QSERDES_V3_TX_PRE_STALL_LDO_BOOST_EN		0x028
+
+#define QSERDES_V3_TX_TX_BAND				0x02c
+#define QSERDES_V3_TX_SLEW_CNTL				0x030
+#define QSERDES_V3_TX_INTERFACE_SELECT			0x034
+#define QSERDES_V3_TX_RES_CODE_LANE_TX			0x03c
+#define QSERDES_V3_TX_RES_CODE_LANE_RX			0x040
 #define QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX		0x044
 #define QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX		0x048
 #define QSERDES_V3_TX_DEBUG_BUS_SEL			0x058
+#define QSERDES_V3_TX_TRANSCEIVER_BIAS_EN		0x05c
 #define QSERDES_V3_TX_HIGHZ_DRVR_EN			0x060
+#define QSERDES_V3_TX_TX_POL_INV			0x064
+#define QSERDES_V3_TX_PARRATE_REC_DETECT_IDLE_EN	0x068
 #define QSERDES_V3_TX_LANE_MODE_1			0x08c
 #define QSERDES_V3_TX_RCV_DETECT_LVL_2			0x0a4
+#define QSERDES_V3_TX_TRAN_DRVR_EMP_EN			0x0c0
+#define QSERDES_V3_TX_TX_INTERFACE_MODE			0x0c4
+#define QSERDES_V3_TX_VMODE_CTRL1			0x0f0
 
 /* Only for QMP V3 PHY - RX registers */
 #define QSERDES_V3_RX_UCDR_FO_GAIN			0x008
@@ -313,6 +347,52 @@
 #define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG4		0x5c
 #define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG5		0x60
 
+/* Only for QMP V3 PHY - DP PHY registers */
+#define QSERDES_V3_DP_PHY_REVISION_ID0			0x000
+#define QSERDES_V3_DP_PHY_REVISION_ID1			0x004
+#define QSERDES_V3_DP_PHY_REVISION_ID2			0x008
+#define QSERDES_V3_DP_PHY_REVISION_ID3			0x00c
+#define QSERDES_V3_DP_PHY_CFG				0x010
+#define QSERDES_V3_DP_PHY_PD_CTL			0x018
+# define DP_PHY_PD_CTL_PWRDN				0x001
+# define DP_PHY_PD_CTL_PSR_PWRDN			0x002
+# define DP_PHY_PD_CTL_AUX_PWRDN			0x004
+# define DP_PHY_PD_CTL_LANE_0_1_PWRDN			0x008
+# define DP_PHY_PD_CTL_LANE_2_3_PWRDN			0x010
+# define DP_PHY_PD_CTL_PLL_PWRDN			0x020
+# define DP_PHY_PD_CTL_DP_CLAMP_EN			0x040
+#define QSERDES_V3_DP_PHY_MODE				0x01c
+#define QSERDES_V3_DP_PHY_AUX_CFG0			0x020
+#define QSERDES_V3_DP_PHY_AUX_CFG1			0x024
+#define QSERDES_V3_DP_PHY_AUX_CFG2			0x028
+#define QSERDES_V3_DP_PHY_AUX_CFG3			0x02c
+#define QSERDES_V3_DP_PHY_AUX_CFG4			0x030
+#define QSERDES_V3_DP_PHY_AUX_CFG5			0x034
+#define QSERDES_V3_DP_PHY_AUX_CFG6			0x038
+#define QSERDES_V3_DP_PHY_AUX_CFG7			0x03c
+#define QSERDES_V3_DP_PHY_AUX_CFG8			0x040
+#define QSERDES_V3_DP_PHY_AUX_CFG9			0x044
+
+#define QSERDES_V3_DP_PHY_AUX_INTERRUPT_MASK		0x048
+# define PHY_AUX_STOP_ERR_MASK				0x01
+# define PHY_AUX_DEC_ERR_MASK 				0x02
+# define PHY_AUX_SYNC_ERR_MASK				0x04
+# define PHY_AUX_ALIGN_ERR_MASK				0x08
+# define PHY_AUX_REQ_ERR_MASK				0x10
+
+#define QSERDES_V3_DP_PHY_AUX_INTERRUPT_CLEAR		0x04c
+#define QSERDES_V3_DP_PHY_AUX_BIST_CFG			0x050
+
+#define QSERDES_V3_DP_PHY_VCO_DIV			0x064
+#define QSERDES_V3_DP_PHY_TX0_TX1_LANE_CTL		0x06c
+#define QSERDES_V3_DP_PHY_TX2_TX3_LANE_CTL		0x088
+
+#define QSERDES_V3_DP_PHY_SPARE0			0x0ac
+#define DP_PHY_SPARE0_MASK				0x0f
+#define DP_PHY_SPARE0_ORIENTATION_INFO_SHIFT		0x04(0x0004)
+
+#define QSERDES_V3_DP_PHY_STATUS			0x0c0
+
 /* Only for QMP V4 PHY - QSERDES COM registers */
 #define QSERDES_V4_COM_SSC_EN_CENTER			0x010
 #define QSERDES_V4_COM_SSC_PER1				0x01c
