@@ -9,6 +9,12 @@
#include <linux/regmap.h>
#include <linux/watchdog.h>
+#define PON_POFF_REASON1 0x0c
+#define PON_POFF_REASON1_PMIC_WD BIT(2)
+#define PON_POFF_REASON2 0x0d
+#define PON_POFF_REASON2_UVLO BIT(5)
+#define PON_POFF_REASON2_OTST3 BIT(6)
+
#define PON_INT_RT_STS 0x10
#define PMIC_WD_BARK_STS_BIT BIT(6)
@@ -110,12 +116,14 @@ static irqreturn_t pm8916_wdt_isr(int irq, void *arg)
}
static const struct watchdog_info pm8916_wdt_ident = {
- .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE,
+ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE |
+ WDIOF_OVERHEAT | WDIOF_CARDRESET | WDIOF_POWERUNDER,
.identity = "QCOM PM8916 PON WDT",
};
static const struct watchdog_info pm8916_wdt_pt_ident = {
.options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE |
+ WDIOF_OVERHEAT | WDIOF_CARDRESET | WDIOF_POWERUNDER |
WDIOF_PRETIMEOUT,
.identity = "QCOM PM8916 PON WDT",
};
@@ -135,6 +143,7 @@ static int pm8916_wdt_probe(struct platform_device *pdev)
struct pm8916_wdt *wdt;
struct device *parent;
int err, irq;
+ u8 poff[2];
wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
if (!wdt)
@@ -175,6 +184,20 @@ static int pm8916_wdt_probe(struct platform_device *pdev)
wdt->wdev.info = &pm8916_wdt_ident;
}
+ err = regmap_bulk_read(wdt->regmap, wdt->baseaddr + PON_POFF_REASON1,
+ &poff, ARRAY_SIZE(poff));
+ if (err == 0) {
+ dev_dbg(dev, "POFF reason: %#x %#x\n", poff[0], poff[1]);
+ if (poff[0] & PON_POFF_REASON1_PMIC_WD)
+ wdt->wdev.bootstatus |= WDIOF_CARDRESET;
+ if (poff[1] & PON_POFF_REASON2_UVLO)
+ wdt->wdev.bootstatus |= WDIOF_POWERUNDER;
+ if (poff[1] & PON_POFF_REASON2_OTST3)
+ wdt->wdev.bootstatus |= WDIOF_OVERHEAT;
+ } else {
+ dev_err(dev, "failed to read POFF reason: %d\n", err);
+ }
+
/* Configure watchdog to hard-reset mode */
err = regmap_write(wdt->regmap,
wdt->baseaddr + PON_PMIC_WD_RESET_S2_CTL,
The PM8916 PMIC provides "power-off reason" (POFF_REASON) registers to allow detecting why the board was powered off or rebooted. This can be used to expose if a reset happened due to a watchdog timeout. The watchdog API also provides status bits for overtemperature and undervoltage which happen to be reported in the same PMIC register. Make this information available as part of the watchdog device so userspace can decide to handle the situation accordingly. Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> --- drivers/watchdog/pm8916_wdt.c | 25 ++++++++++++++++++++++++- 1 file changed, 24 insertions(+), 1 deletion(-)