diff mbox series

[v2,2/3] ARM: dts: qcom: msm8960: add the device node of USB1

Message ID 20220730081412.14297-1-peremen@gmail.com
State Superseded
Headers show
Series [v2,1/3] ARM: dts: qcom: msm8960: change the device node of sleep_clk | expand

Commit Message

Shinjo Park July 30, 2022, 8:14 a.m. UTC 
Use the same USB definition as qcom-apq8064.dtsi, tested on Casio GzOne.

Signed-off-by: Shinjo Park <peremen@gmail.com>
Reviewed-by: David Heidelberg <david@ixit.cz>
---

v2:
 - Rewrite commit message
 - Reorder status line

 arch/arm/boot/dts/qcom-msm8960.dtsi | 32 +++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

Comments

Rudraksha Gupta Aug. 2, 2022, 5:21 a.m. UTC | #1 
> #include <dt-bindings/clock/qcom,lcc-msm8960.h>
Does not apply cleanly to mainline. Please include the above
Shinjo Park Aug. 3, 2022, 7:29 a.m. UTC | #2 
On 2022년 8월 2일 화요일 오전 7시 21분 54초 CEST Rudraksha Gupta wrote:
>  > #include <dt-bindings/clock/qcom,lcc-msm8960.h>
> 
> Does not apply cleanly to mainline. Please include the above

Will be fixed in the next revision of this patch.
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index e1f010c9643e..4c8a67c0cc7b 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -4,6 +4,7 @@ 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8960.h>
 #include <dt-bindings/clock/qcom,lcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
 #include <dt-bindings/mfd/qcom-rpm.h>
 #include <dt-bindings/soc/qcom,gsbi.h>
 
@@ -201,6 +202,37 @@  regulators {
 			};
 		};
 
+		usb1: usb@12500000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			#reset-cells = <1>;
+			status = "disabled";
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8960",
+						     "qcom,usb-hs-phy";
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+					#phy-cells = <0>;
+				};
+			};
+		};
+
 		acc0: clock-controller@2088000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;