[v6,2/2] arm64: dts: qcom: add SA8540P ride(Qdrive-3)

Introduce the Qualcomm SA8540P ride automotive platform, also known as
Qdrive-3 development board.

This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs and USB.

The SA8540P ride contains four PM8450 PMICs.

Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
---
 arch/arm64/boot/dts/qcom/Makefile         |   1 +
 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 309 ++++++++++++++++++++++
 2 files changed, 310 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-ride.dts

On Thu, Oct 20, 2022 at 01:49:23PM +0200, konrad.dybcio@somainline.org wrote:
> On 2022-10-20 09:30, Parikshit Pareek wrote:
> > Introduce the Qualcomm SA8540P ride automotive platform, also known as
> > Qdrive-3 development board.
> > 
> > This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
> > regulators, debug UART, PMICs, remoteprocs and USB.
> > 
> > The SA8540P ride contains four PM8450 PMICs.
> > 
> > Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
> > ---
> 
> Hi!
> 
> [...[
> 
> > +		vreg_l3c: ldo3 {
> > +			regulator-name = "vreg_l3c";
> > +			regulator-min-microvolt = <1200000>;
> > +			regulator-max-microvolt = <1200000>;
> > +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > +			regulator-allow-set-load;
> Not sure if setting load is desired after recent rpmh regulator changes.
May I know the exact patch being refered here?
> 
> [...]
> 
> > +
> > +&spmi_bus {
> > +	pm8450a: pmic@0 {
> > +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> Please add a pm8450[aceg].dtsi instead, as other boards would probably like
> to
> reuse this. Also, move the spmi.h inclusion there.
> 
> [...]
> 
> > +};
> > +
> > +/* PINCTRL */
> Not sure if it's useful if there's nothing there for now.
> 
> Konrad

Regards,
Parikshit Pareek

On Fri, Oct 28, 2022 at 01:20:59PM +0530, Parikshit Pareek wrote:
> > > +		vreg_l3c: ldo3 {
> > > +			regulator-name = "vreg_l3c";
> > > +			regulator-min-microvolt = <1200000>;
> > > +			regulator-max-microvolt = <1200000>;
> > > +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> > > +			regulator-allow-set-load;
> > Not sure if setting load is desired after recent rpmh regulator changes.
>
> May I know the exact patch being refered here?

Hi Parikshit,

You now need to specify a regulator-allowed-modes. Here's some links
with more information:

https://lore.kernel.org/all/20220907204924.173030-1-ahalaney@redhat.com/
https://lore.kernel.org/all/20220824142229.RFT.v2.2.I6f77860e5cd98bf5c67208fa9edda4a08847c304@changeid/

Brian

On 10/20/2022 1:00 PM, Parikshit Pareek wrote:
> Introduce the Qualcomm SA8540P ride automotive platform, also known as
> Qdrive-3 development board.
> 
> This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
> regulators, debug UART, PMICs, remoteprocs and USB.
> 
> The SA8540P ride contains four PM8450 PMICs.
> 
> Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
> ---
>   arch/arm64/boot/dts/qcom/Makefile         |   1 +
>   arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 309 ++++++++++++++++++++++
>   2 files changed, 310 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index b0558d3389e5..c89d44756791 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -54,6 +54,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> new file mode 100644
> index 000000000000..0faf06625b05
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -0,0 +1,309 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +#include "sa8540p.dtsi"
> +
> +/ {
> +	model = "Qualcomm SA8540P Ride";
> +	compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
> +
> +	aliases {
> +		serial0 = &qup2_uart17;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +};
> +
> +&apps_rsc {
> +	pmm8540-a-regulators {
> +		compatible = "qcom,pm8150-rpmh-regulators";
> +		qcom,pmic-id = "a";
> +
> +		vreg_l3a: ldo3 {
> +			regulator-name = "vreg_l3a";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1208000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l5a: ldo5 {
> +			regulator-name = "vreg_l5a";
> +			regulator-min-microvolt = <912000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7a: ldo7 {
> +			regulator-name = "vreg_l7a";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l13a: ldo13 {
> +			regulator-name = "vreg_l13a";
> +			regulator-min-microvolt = <3072000>;
> +			regulator-max-microvolt = <3072000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	pmm8540-c-regulators {
> +		compatible = "qcom,pm8150-rpmh-regulators";
> +		qcom,pmic-id = "c";
> +
> +		vreg_l1c: ldo1 {
> +			regulator-name = "vreg_l1c";
> +			regulator-min-microvolt = <912000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2c: ldo2 {
> +			regulator-name = "vreg_l2c";
> +			regulator-min-microvolt = <3072000>;
> +			regulator-max-microvolt = <3072000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3c: ldo3 {
> +			regulator-name = "vreg_l3c";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +		};
As we don't have ufs_card_hc for ride platform, we can remove vreg_l3c.
> +
> +		vreg_l4c: ldo4 {
> +			regulator-name = "vreg_l4c";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1208000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6c: ldo6 {
> +			regulator-name = "vreg_l6c";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l7c: ldo7 {
> +			regulator-name = "vreg_l7c";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l10c: ldo10 {
> +			regulator-name = "vreg_l10c";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2504000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +		};
Similarly we can remove this vreg_l10c.
> +
> +		vreg_l17c: ldo17 {
> +			regulator-name = "vreg_l17c";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2504000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +		};
> +	};
> +
> +	pmm8540-g-regulators {
> +		compatible = "qcom,pm8150-rpmh-regulators";
> +		qcom,pmic-id = "g";
> +
> +		vreg_l3g: ldo3 {
> +			regulator-name = "vreg_l3g";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7g: ldo7 {
> +			regulator-name = "vreg_l7g";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8g: ldo8 {
> +			regulator-name = "vreg_l8g";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <880000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +};
> +
> +&qup2 {
> +	status = "okay";
> +};
> +
> +&qup2_uart17 {
> +	compatible = "qcom,geni-debug-uart";
> +	status = "okay";
> +};
> +
> +&remoteproc_adsp {
> +	firmware-name = "qcom/sa8540p/adsp.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_nsp0 {
> +	firmware-name = "qcom/sa8540p/cdsp.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_nsp1 {
> +	firmware-name = "qcom/sa8540p/cdsp1.mbn";
> +	status = "okay";
> +};
> +
> +&spmi_bus {
> +	pm8450a: pmic@0 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x0 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450a_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450a_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pm8450c: pmic@4 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x4 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450c_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450c_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pm8450e: pmic@8 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x8 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450e_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450e_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pm8450g: pmic@c {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0xc SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450g_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450g_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +};
> +
> +&ufs_mem_hc {
> +	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
> +
> +	vcc-supply = <&vreg_l17c>;
> +	vcc-max-microamp = <800000>;
> +	vccq-supply = <&vreg_l6c>;
> +	vccq-max-microamp = <900000>;
> +
> +	status = "okay";
> +};
> +
> +&ufs_mem_phy {
> +	vdda-phy-supply = <&vreg_l8g>;
> +	vdda-pll-supply = <&vreg_l3g>;
> +
> +	status = "okay";
> +};
> +
> +&usb_0 {
> +	status = "okay";
> +};
> +
> +&usb_0_dwc3 {
> +	/* TODO: Define USB-C connector properly */
> +	dr_mode = "peripheral";
> +};
> +
> +&usb_0_hsphy {
> +	vdda-pll-supply = <&vreg_l5a>;
> +	vdda18-supply = <&vreg_l7a>;
> +	vdda33-supply = <&vreg_l13a>;
> +
> +	status = "okay";
> +};
> +
> +&usb_0_qmpphy {
> +	vdda-phy-supply = <&vreg_l3a>;
> +	vdda-pll-supply = <&vreg_l5a>;
> +
> +	status = "okay";
> +};
> +
> +&usb_2_hsphy0 {
> +	vdda-pll-supply = <&vreg_l5a>;
> +	vdda18-supply = <&vreg_l7g>;
> +	vdda33-supply = <&vreg_l13a>;
> +
> +	status = "okay";
> +};
> +
> +&usb_2_qmpphy0 {
> +	vdda-phy-supply = <&vreg_l3a>;
> +	vdda-pll-supply = <&vreg_l5a>;
> +
> +	status = "okay";
> +};
> +
> +&xo_board_clk {
> +	clock-frequency = <38400000>;
> +};
> +
> +/* PINCTRL */