new file mode 100644
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pmk8350: pmic@6 {
+ compatible = "qcom,pmk8350", "qcom,spmi-pmic";
+ reg = <0x6 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmk8350_pon: pon@1300 {
+ compatible = "qcom,pm8998-pon";
+ reg = <0x1300>;
+
+ pon_pwrkey: pwrkey {
+ compatible = "qcom,pmk8350-pwrkey";
+ interrupts = <0x6 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+ linux,code = <KEY_POWER>;
+ status = "disabled";
+ };
+
+ pon_resin: resin {
+ compatible = "qcom,pmk8350-resin";
+ interrupts = <0x6 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
+ status = "disabled";
+ };
+ };
+
+ pmk8350_vadc: adc@3100 {
+ compatible = "qcom,spmi-adc7";
+ reg = <0x3100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0x6 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #io-channel-cells = <1>;
+ };
+
+ pmk8350_adc_tm: adc-tm@3400 {
+ compatible = "qcom,adc-tm7";
+ reg = <0x3400>;
+ interrupts = <0x6 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #thermal-sensor-cells = <1>;
+ status = "disabled";
+ };
+
+ pmk8350_rtc: rtc@6100 {
+ compatible = "qcom,pmk8350-rtc";
+ reg = <0x6100>, <0x6200>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x6 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
+
+ pmk8350_gpios: gpio@b000 {
+ compatible = "qcom,pmk8350-gpio", "qcom,spmi-gpio";
+ reg = <0xb000>;
+ gpio-controller;
+ gpio-ranges = <&pmk8350_gpios 0 0 4>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
PMK8350 is shipped on SID6 with some SoCs, for example with SM6375. Add a DT with the SID changed to allow it to work. Unfortunately, the entire DT needs to be copied even if the diff is very little, as the node names are not unique. Including pm6125 and pmk8350 together for example, would make pmk8350 overwrite the pm6125 node, as both are defined as 'pmic@0'. Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> --- arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi | 73 ++++++++++++++++++++++ 1 file changed, 73 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/pmk8350_sid6.dtsi