diff mbox series

[v3,7/8] arm64: dts: qcom: sm8350: add PCIe devices

Message ID 20221110183158.856242-8-dmitry.baryshkov@linaro.org
State Superseded
Headers show
Series PCI/phy: Add support for PCI on sm8350 platform | expand

Commit Message

Dmitry Baryshkov Nov. 10, 2022, 6:31 p.m. UTC
Add PCIe0 and PCIe1 (and corresponding PHY) devices found on SM8350
platform. The PCIe0 is a 1-lane Gen3 host, PCIe1 is a 2-lane Gen3 host.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8350.dtsi | 246 ++++++++++++++++++++++++++-
 1 file changed, 244 insertions(+), 2 deletions(-)

Comments

Johan Hovold Nov. 16, 2022, 2:50 p.m. UTC | #1
On Thu, Nov 10, 2022 at 09:31:57PM +0300, Dmitry Baryshkov wrote:
> Add PCIe0 and PCIe1 (and corresponding PHY) devices found on SM8350
> platform. The PCIe0 is a 1-lane Gen3 host, PCIe1 is a 2-lane Gen3 host.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/sm8350.dtsi | 246 ++++++++++++++++++++++++++-
>  1 file changed, 244 insertions(+), 2 deletions(-)

> +		pcie0: pci@1c00000 {
> +			compatible = "qcom,pcie-sm8350";
> +			reg = <0 0x01c00000 0 0x3000>,
> +			      <0 0x60000000 0 0xf1d>,
> +			      <0 0x60000f20 0 0xa8>,
> +			      <0 0x60001000 0 0x1000>,
> +			      <0 0x60100000 0 0x100000>;
> +			reg-names = "parf", "dbi", "elbi", "atu", "config";
> +			device_type = "pci";
> +			linux,pci-domain = <0>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <1>;
> +
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
> +				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
> +
> +			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi0", "msi1", "msi2", "msi3",
> +					  "msi4", "msi5", "msi6", "msi7";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> +			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
> +				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
> +				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
> +				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
> +				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
> +				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
> +				 <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
> +				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
> +			clock-names = "aux",
> +				      "cfg",
> +				      "bus_master",
> +				      "bus_slave",
> +				      "slave_q2a",
> +				      "tbu",
> +				      "ddrss_sf_tbu",
> +				      "aggre0",
> +				      "aggre1";
> +
> +			iommus = <&apps_smmu 0x1c00 0x7f>;
> +			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
> +				    <0x100 &apps_smmu 0x1c01 0x1>;
> +
> +			resets = <&gcc GCC_PCIE_0_BCR>;
> +			reset-names = "pci";
> +
> +			power-domains = <&gcc PCIE_0_GDSC>;
> +
> +			phys = <&pcie0_phy>;
> +			phy-names = "pciephy";
> +
> +			perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
> +			wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pcie0_default_state>;

So I still think these do not belong in the dtsi for the reasons I just
gave in a reply to v2.

> +
> +			status = "disabled";
> +		};
> +
> +		pcie0_phy: phy@1c06000 {
> +			compatible = "qcom,sm8350-qmp-gen3x1-pcie-phy";
> +			reg = <0 0x01c06000 0 0x2000>;

> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;

These three should not be here (same for pcie1).

> +			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
> +				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_0_CLKREF_EN>,
> +				 <&gcc GCC_PCIE0_PHY_RCHNG_CLK>,
> +				 <&gcc GCC_PCIE_0_PIPE_CLK>;
> +			clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe";
> +
> +			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
> +			reset-names = "phy";
> +
> +			assigned-clocks = <&gcc GCC_PCIE0_PHY_RCHNG_CLK>;
> +			assigned-clock-rates = <100000000>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "pcie_0_pipe_clk";
> +
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};

>  		lpass_ag_noc: interconnect@3c40000 {
>  			compatible = "qcom,sm8350-lpass-ag-noc";
>  			reg = <0 0x03c40000 0 0xf080>;
> @@ -1761,6 +1957,52 @@ tlmm: pinctrl@f100000 {
>  			gpio-ranges = <&tlmm 0 0 204>;
>  			wakeup-parent = <&pdc>;
>  
> +			pcie0_default_state: pcie0-default-state {
> +				perst-pins {
> +					pins = "gpio94";
> +					function = "gpio";
> +					drive-strength = <2>;
> +					bias-pull-down;
> +				};
> +
> +				clkreq-pins {
> +					pins = "gpio95";
> +					function = "pcie0_clkreqn";
> +					drive-strength = <2>;
> +					bias-pull-up;
> +				};
> +
> +				wake-pins {
> +					pins = "gpio96";
> +					function = "gpio";
> +					drive-strength = <2>;
> +					bias-pull-up;
> +				};
> +			};
> +
> +			pcie1_default_state: pcie1-default-state {
> +				perst-pins {
> +					pins = "gpio97";
> +					function = "gpio";
> +					drive-strength = <2>;
> +					bias-pull-down;
> +				};
> +
> +				clkreq-pins {
> +					pins = "gpio98";
> +					function = "pcie1_clkreqn";
> +					drive-strength = <2>;
> +					bias-pull-up;
> +				};
> +
> +				wake-pins {
> +					pins = "gpio99";
> +					function = "gpio";
> +					drive-strength = <2>;
> +					bias-pull-up;
> +				};
> +			};
> +
>  			qup_uart3_default_state: qup-uart3-default-state {
>  				rx-pins {
>  					pins = "gpio18";

Johan
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index a86d9ea93b9d..90a26f406bf3 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -656,8 +656,8 @@  gcc: clock-controller@100000 {
 				      "usb3_uni_phy_sec_gcc_usb30_pipe_clk";
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 				 <&sleep_clk>,
-				 <0>,
-				 <0>,
+				 <&pcie0_phy>,
+				 <&pcie1_phy>,
 				 <0>,
 				 <0>,
 				 <0>,
@@ -1582,6 +1582,202 @@  mmss_noc: interconnect@1740000 {
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		pcie0: pci@1c00000 {
+			compatible = "qcom,pcie-sm8350";
+			reg = <0 0x01c00000 0 0x3000>,
+			      <0 0x60000000 0 0xf1d>,
+			      <0 0x60000f20 0 0xa8>,
+			      <0 0x60001000 0 0x1000>,
+			      <0 0x60100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0", "msi1", "msi2", "msi3",
+					  "msi4", "msi5", "msi6", "msi7";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "tbu",
+				      "ddrss_sf_tbu",
+				      "aggre0",
+				      "aggre1";
+
+			iommus = <&apps_smmu 0x1c00 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
+				    <0x100 &apps_smmu 0x1c01 0x1>;
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+
+			perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie0_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie0_phy: phy@1c06000 {
+			compatible = "qcom,sm8350-qmp-gen3x1-pcie-phy";
+			reg = <0 0x01c06000 0 0x2000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE0_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_0_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE0_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie_0_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		pcie1: pci@1c08000 {
+			compatible = "qcom,pcie-sm8350";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40001000 0 0x1000>,
+			      <0 0x40100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x40200000 0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0 0x40300000 0x0 0x1fd00000>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "tbu",
+				      "ddrss_sf_tbu",
+				      "aggre1";
+
+			iommus = <&apps_smmu 0x1c80 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1c80 0x1>,
+				    <0x100 &apps_smmu 0x1c81 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+
+			perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie1_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0f000 {
+			compatible = "qcom,sm8350-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c0e000 0 0x2000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_CLKREF_EN>,
+				 <&gcc GCC_PCIE1_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie_1_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		lpass_ag_noc: interconnect@3c40000 {
 			compatible = "qcom,sm8350-lpass-ag-noc";
 			reg = <0 0x03c40000 0 0xf080>;
@@ -1761,6 +1957,52 @@  tlmm: pinctrl@f100000 {
 			gpio-ranges = <&tlmm 0 0 204>;
 			wakeup-parent = <&pdc>;
 
+			pcie0_default_state: pcie0-default-state {
+				perst-pins {
+					pins = "gpio94";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq-pins {
+					pins = "gpio95";
+					function = "pcie0_clkreqn";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake-pins {
+					pins = "gpio96";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			pcie1_default_state: pcie1-default-state {
+				perst-pins {
+					pins = "gpio97";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq-pins {
+					pins = "gpio98";
+					function = "pcie1_clkreqn";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake-pins {
+					pins = "gpio99";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
 			qup_uart3_default_state: qup-uart3-default-state {
 				rx-pins {
 					pins = "gpio18";