| Message ID | 20221116121732.2731448-2-abel.vesa@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | ufs: host: ufs-qcom: Add support for SM8550 | expand |
On 16/11/2022 13:17, Abel Vesa wrote: > On SM8550, depending on the Qunipro, we can run with G5 or G4. > For now, when the major version is 5 or above, we go with G5. > Therefore, we need to specifically tell UFS HC that. > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > --- > drivers/ufs/host/ufs-qcom.c | 4 ++++ > drivers/ufs/host/ufs-qcom.h | 2 ++ > 2 files changed, 6 insertions(+) > > diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c > index ca60a5b0292b..72334aefe81c 100644 > --- a/drivers/ufs/host/ufs-qcom.c > +++ b/drivers/ufs/host/ufs-qcom.c > @@ -227,6 +227,10 @@ static void ufs_qcom_select_unipro_mode(struct ufs_qcom_host *host) > ufshcd_rmwl(host->hba, QUNIPRO_SEL, > ufs_qcom_cap_qunipro(host) ? QUNIPRO_SEL : 0, > REG_UFS_CFG1); > + > + if (host->hw_ver.major == 0x05) > + ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 0, REG_UFS_CFG0); > + > /* make sure above configuration is applied before we return */ > mb(); > } > diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h > index 751ded3e3531..10621055bf7f 100644 > --- a/drivers/ufs/host/ufs-qcom.h > +++ b/drivers/ufs/host/ufs-qcom.h > @@ -36,6 +36,7 @@ enum { > /* On older UFS revisions, this register is called "RETRY_TIMER_REG" */ > REG_UFS_PARAM0 = 0xD0, > REG_UFS_PA_LINK_STARTUP_TIMER = 0xD8, > + REG_UFS_CFG0 = 0xD8, Are you sure these two should point to the same register? Maybe it deserves some kind of a comment? Konrad > REG_UFS_CFG1 = 0xDC, > REG_UFS_CFG2 = 0xE0, > REG_UFS_HW_VERSION = 0xE4, > @@ -75,6 +76,7 @@ enum { > > /* bit definitions for REG_UFS_CFG1 register */ > #define QUNIPRO_SEL BIT(0) > +#define QUNIPRO_G4_SEL BIT(5) > #define UFS_PHY_SOFT_RESET BIT(1) > #define UTP_DBG_RAMS_EN BIT(17) > #define TEST_BUS_EN BIT(18)
On 22-11-16 13:28:53, Konrad Dybcio wrote: > > > On 16/11/2022 13:17, Abel Vesa wrote: > > On SM8550, depending on the Qunipro, we can run with G5 or G4. > > For now, when the major version is 5 or above, we go with G5. > > Therefore, we need to specifically tell UFS HC that. > > > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > > --- > > drivers/ufs/host/ufs-qcom.c | 4 ++++ > > drivers/ufs/host/ufs-qcom.h | 2 ++ > > 2 files changed, 6 insertions(+) > > > > diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c > > index ca60a5b0292b..72334aefe81c 100644 > > --- a/drivers/ufs/host/ufs-qcom.c > > +++ b/drivers/ufs/host/ufs-qcom.c > > @@ -227,6 +227,10 @@ static void ufs_qcom_select_unipro_mode(struct ufs_qcom_host *host) > > ufshcd_rmwl(host->hba, QUNIPRO_SEL, > > ufs_qcom_cap_qunipro(host) ? QUNIPRO_SEL : 0, > > REG_UFS_CFG1); > > + > > + if (host->hw_ver.major == 0x05) > > + ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 0, REG_UFS_CFG0); > > + > > /* make sure above configuration is applied before we return */ > > mb(); > > } > > diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h > > index 751ded3e3531..10621055bf7f 100644 > > --- a/drivers/ufs/host/ufs-qcom.h > > +++ b/drivers/ufs/host/ufs-qcom.h > > @@ -36,6 +36,7 @@ enum { > > /* On older UFS revisions, this register is called "RETRY_TIMER_REG" */ > > REG_UFS_PARAM0 = 0xD0, > > REG_UFS_PA_LINK_STARTUP_TIMER = 0xD8, > > + REG_UFS_CFG0 = 0xD8, > Are you sure these two should point to the same register? Maybe it deserves > some kind of a comment? The REG_UFS_PA_LINK_STARTUP_TIMER is used by non qunipro variants. (UFS versions below 2.x) The REG_UFS_CFG0 is used by qunipro variants. (UFS versions above 2.x). Will add a comment to the later one that would look like this: "/* Found on UFS versions above 2.x only */" Thanks, Abel > > Konrad > > REG_UFS_CFG1 = 0xDC, > > REG_UFS_CFG2 = 0xE0, > > REG_UFS_HW_VERSION = 0xE4, > > @@ -75,6 +76,7 @@ enum { > > /* bit definitions for REG_UFS_CFG1 register */ > > #define QUNIPRO_SEL BIT(0) > > +#define QUNIPRO_G4_SEL BIT(5) > > #define UFS_PHY_SOFT_RESET BIT(1) > > #define UTP_DBG_RAMS_EN BIT(17) > > #define TEST_BUS_EN BIT(18)
On Wed, Nov 16, 2022 at 02:17:31PM +0200, Abel Vesa wrote: > On SM8550, depending on the Qunipro, we can run with G5 or G4. > For now, when the major version is 5 or above, we go with G5. > Therefore, we need to specifically tell UFS HC that. > > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > --- > drivers/ufs/host/ufs-qcom.c | 4 ++++ > drivers/ufs/host/ufs-qcom.h | 2 ++ > 2 files changed, 6 insertions(+) > > diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c > index ca60a5b0292b..72334aefe81c 100644 > --- a/drivers/ufs/host/ufs-qcom.c > +++ b/drivers/ufs/host/ufs-qcom.c > @@ -227,6 +227,10 @@ static void ufs_qcom_select_unipro_mode(struct ufs_qcom_host *host) > ufshcd_rmwl(host->hba, QUNIPRO_SEL, > ufs_qcom_cap_qunipro(host) ? QUNIPRO_SEL : 0, > REG_UFS_CFG1); > + > + if (host->hw_ver.major == 0x05) > + ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 0, REG_UFS_CFG0); So this means, G5 will be used all the time even if the UFS device doesn't support it (ie., G4 device), which is not ideal. Since you have already based this series on my UFS gear 4 series, you should resend this on top of my next version that I'm about to submit. There I have proposed reinitializing the UFS device after switching to max gear supported by both controller and device. Based on that information, you could do: ``` if (host->hw_ver.major == 0x05) { if (host->hs_hear == UFS_HS_G5) ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 0, REG_UFS_CFG0); else ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 1, REG_UFS_CFG0); } ``` By this way, if the device doesn't support G5, G4 will be used. Btw, please use a valid definition instead of 0/1 above. > + > /* make sure above configuration is applied before we return */ > mb(); > } > diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h > index 751ded3e3531..10621055bf7f 100644 > --- a/drivers/ufs/host/ufs-qcom.h > +++ b/drivers/ufs/host/ufs-qcom.h > @@ -36,6 +36,7 @@ enum { > /* On older UFS revisions, this register is called "RETRY_TIMER_REG" */ > REG_UFS_PARAM0 = 0xD0, > REG_UFS_PA_LINK_STARTUP_TIMER = 0xD8, > + REG_UFS_CFG0 = 0xD8, Hmm, so what is the offset of REG_UFS_PA_LINK_STARTUP_TIMER? > REG_UFS_CFG1 = 0xDC, > REG_UFS_CFG2 = 0xE0, > REG_UFS_HW_VERSION = 0xE4, > @@ -75,6 +76,7 @@ enum { > > /* bit definitions for REG_UFS_CFG1 register */ > #define QUNIPRO_SEL BIT(0) > +#define QUNIPRO_G4_SEL BIT(5) Since this bit belongs to CFG0 register, it should be added separately and not with CFG1 definitions. Thanks, Mani > #define UFS_PHY_SOFT_RESET BIT(1) > #define UTP_DBG_RAMS_EN BIT(17) > #define TEST_BUS_EN BIT(18) > -- > 2.34.1 >
diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c index ca60a5b0292b..72334aefe81c 100644 --- a/drivers/ufs/host/ufs-qcom.c +++ b/drivers/ufs/host/ufs-qcom.c @@ -227,6 +227,10 @@ static void ufs_qcom_select_unipro_mode(struct ufs_qcom_host *host) ufshcd_rmwl(host->hba, QUNIPRO_SEL, ufs_qcom_cap_qunipro(host) ? QUNIPRO_SEL : 0, REG_UFS_CFG1); + + if (host->hw_ver.major == 0x05) + ufshcd_rmwl(host->hba, QUNIPRO_G4_SEL, 0, REG_UFS_CFG0); + /* make sure above configuration is applied before we return */ mb(); } diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h index 751ded3e3531..10621055bf7f 100644 --- a/drivers/ufs/host/ufs-qcom.h +++ b/drivers/ufs/host/ufs-qcom.h @@ -36,6 +36,7 @@ enum { /* On older UFS revisions, this register is called "RETRY_TIMER_REG" */ REG_UFS_PARAM0 = 0xD0, REG_UFS_PA_LINK_STARTUP_TIMER = 0xD8, + REG_UFS_CFG0 = 0xD8, REG_UFS_CFG1 = 0xDC, REG_UFS_CFG2 = 0xE0, REG_UFS_HW_VERSION = 0xE4, @@ -75,6 +76,7 @@ enum { /* bit definitions for REG_UFS_CFG1 register */ #define QUNIPRO_SEL BIT(0) +#define QUNIPRO_G4_SEL BIT(5) #define UFS_PHY_SOFT_RESET BIT(1) #define UTP_DBG_RAMS_EN BIT(17) #define TEST_BUS_EN BIT(18)
On SM8550, depending on the Qunipro, we can run with G5 or G4. For now, when the major version is 5 or above, we go with G5. Therefore, we need to specifically tell UFS HC that. Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- drivers/ufs/host/ufs-qcom.c | 4 ++++ drivers/ufs/host/ufs-qcom.h | 2 ++ 2 files changed, 6 insertions(+)