diff mbox series

[v3,1/3] arm64: dts: qcom: sm8550: add display hardware devices

Message ID 20230104-topic-sm8550-upstream-dts-display-v3-1-46f0d4e57752@linaro.org
State Accepted
Commit d7da51db5b81a04f3d6f36293010ded8bef9e297
Headers show
Series arm64: dts: qcom: sm8550-mtp: enable DSI panel | expand

Commit Message

Neil Armstrong Jan. 18, 2023, 8:55 a.m. UTC
Add devices tree nodes describing display hardware on SM8550:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs

This does not provide support for DP controllers present on the SM8550.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 299 +++++++++++++++++++++++++++++++++++
 1 file changed, 299 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 3d47281a276b..a76ee4e50854 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -6,6 +6,7 @@ 
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/clock/qcom,sm8550-gcc.h>
 #include <dt-bindings/clock/qcom,sm8550-tcsr.h>
+#include <dt-bindings/clock/qcom,sm8550-dispcc.h>
 #include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -1727,6 +1728,304 @@  opp-202000000 {
 			};
 		};
 
+		mdss: display-subsystem@ae00000 {
+			compatible = "qcom,sm8550-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			interconnects = <&mmss_noc MASTER_MDP 0 &gem_noc SLAVE_LLCC 0>,
+				        <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "mdp0-mem", "mdp1-mem";
+
+			iommus = <&apps_smmu 0x1c00 0x2>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,sm8550-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&gcc GCC_DISP_AHB_CLK>,
+					<&gcc GCC_DISP_HF_AXI_CLK>,
+					<&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_CLK>,
+					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				power-domains = <&rpmhpd SM8550_MMCX>;
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dpu_intf2_out: endpoint {
+							remote-endpoint = <&mdss_dsi1_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-325000000 {
+						opp-hz = /bits/ 64 <325000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-375000000 {
+						opp-hz = /bits/ 64 <375000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-514000000 {
+						opp-hz = /bits/ 64 <514000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				power-domains = <&rpmhpd SM8550_MMCX>;
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+				operating-points-v2 = <&mdss_dsi_opp_table>;
+
+				phys = <&mdss_dsi0_phy>;
+				phy-names = "dsi";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dsi_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@ae95000 {
+				compatible = "qcom,sm8550-dsi-phy-4nm";
+				reg = <0 0x0ae95000 0 0x200>,
+				      <0 0x0ae95200 0 0x280>,
+				      <0 0x0ae95500 0 0x400>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				status = "disabled";
+			};
+
+			mdss_dsi1: dsi@ae96000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <5>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				power-domains = <&rpmhpd SM8550_MMCX>;
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+				operating-points-v2 = <&mdss_dsi_opp_table>;
+
+				phys = <&mdss_dsi1_phy>;
+				phy-names = "dsi";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi1_in: endpoint {
+							remote-endpoint = <&dpu_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi1_phy: phy@ae97000 {
+				compatible = "qcom,sm8550-dsi-phy-4nm";
+				reg = <0 0x0ae97000 0 0x200>,
+				      <0 0x0ae97200 0 0x280>,
+				      <0 0x0ae97500 0 0x400>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		dispcc: clock-controller@af00000 {
+			compatible = "qcom,sm8550-dispcc";
+			reg = <0 0x0af00000 0 0x20000>;
+			clocks = <&bi_tcxo_div2>,
+				 <&bi_tcxo_ao_div2>,
+				 <&gcc GCC_DISP_AHB_CLK>,
+				 <&sleep_clk>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi1_phy 0>,
+				 <&mdss_dsi1_phy 1>,
+				 <0>, /* dp0 */
+				 <0>,
+				 <0>, /* dp1 */
+				 <0>,
+				 <0>, /* dp2 */
+				 <0>,
+				 <0>, /* dp3 */
+				 <0>;
+			power-domains = <&rpmhpd SM8550_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			status = "disabled";
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sm8550-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;