diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 4eebd5161419..4bdd5bb5b3fc 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -997,6 +997,31 @@ config QCOM_SPMI_ADC5
 	  To compile this driver as a module, choose M here: the module will
 	  be called qcom-spmi-adc5.
 
+config QCOM_SPMI_ADC5_GEN3
+	tristate "Qualcomm Technologies Inc. SPMI PMIC5 GEN3 ADC"
+	depends on SPMI && THERMAL
+	select REGMAP_SPMI
+	select QCOM_VADC_COMMON
+	help
+	  This is the IIO Voltage PMIC5 Gen3 ADC driver for Qualcomm Technologies Inc. PMICs.
+
+	  The driver supports reading multiple channels. The ADC is a 16-bit
+	  sigma-delta ADC. The hardware supports calibrated results for
+	  conversion requests and clients include reading phone power supply
+	  voltage, on board system thermistors connected to the PMIC ADC,
+	  PMIC die temperature, charger temperature, battery current, USB voltage
+	  input and voltage signals connected to supported PMIC GPIO pins. The
+	  hardware supports internal pull-up for thermistors and can choose between
+	  a 30k, 100k or 400k ohm pull up using the ADC channels.
+
+	  In addition, the same driver supports ADC thermal monitoring devices too.
+	  They appear as thermal zones with multiple trip points. A thermal client sets
+	  threshold temperature for both warm and cool trips and gets updated when a
+	  threshold is reached.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called qcom-spmi-adc5-gen3.
+
 config RCAR_GYRO_ADC
 	tristate "Renesas R-Car GyroADC driver"
 	depends on ARCH_RCAR_GEN2 || COMPILE_TEST
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index c0803383a7cc..539af17a668f 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -86,6 +86,7 @@ obj-$(CONFIG_NAU7802) += nau7802.o
 obj-$(CONFIG_NPCM_ADC) += npcm_adc.o
 obj-$(CONFIG_PALMAS_GPADC) += palmas_gpadc.o
 obj-$(CONFIG_QCOM_SPMI_ADC5) += qcom-spmi-adc5.o
+obj-$(CONFIG_QCOM_SPMI_ADC5_GEN3) += qcom-spmi-adc5-gen3.o
 obj-$(CONFIG_QCOM_SPMI_IADC) += qcom-spmi-iadc.o
 obj-$(CONFIG_QCOM_SPMI_RRADC) += qcom-spmi-rradc.o
 obj-$(CONFIG_QCOM_VADC_COMMON) += qcom-vadc-common.o
diff --git a/drivers/iio/adc/qcom-spmi-adc5-gen3.c b/drivers/iio/adc/qcom-spmi-adc5-gen3.c
new file mode 100644
index 000000000000..5b5848492245
--- /dev/null
+++ b/drivers/iio/adc/qcom-spmi-adc5-gen3.c
@@ -0,0 +1,1198 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <asm/unaligned.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/adc/qcom-vadc-common.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/log2.h>
+#include <linux/math64.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+
+#include <dt-bindings/iio/adc/qcom,spmi-vadc.h>
+
+#define ADC5_GEN3_HS				0x45
+#define ADC5_GEN3_HS_BUSY			BIT(7)
+#define ADC5_GEN3_HS_READY			BIT(0)
+
+#define ADC5_GEN3_STATUS1			0x46
+#define ADC5_GEN3_STATUS1_CONV_FAULT		BIT(7)
+#define ADC5_GEN3_STATUS1_THR_CROSS		BIT(6)
+#define ADC5_GEN3_STATUS1_EOC			BIT(0)
+
+#define ADC5_GEN3_TM_EN_STS			0x47
+#define ADC5_GEN3_TM_HIGH_STS			0x48
+#define ADC5_GEN3_TM_LOW_STS			0x49
+
+#define ADC5_GEN3_EOC_STS			0x4a
+#define ADC5_GEN3_EOC_CHAN_0			BIT(0)
+
+#define ADC5_GEN3_EOC_CLR			0x4b
+#define ADC5_GEN3_TM_HIGH_STS_CLR		0x4c
+#define ADC5_GEN3_TM_LOW_STS_CLR		0x4d
+#define ADC5_GEN3_CONV_ERR_CLR			0x4e
+#define ADC5_GEN3_CONV_ERR_CLR_REQ		BIT(0)
+
+#define ADC5_GEN3_SID				0x4f
+#define ADC5_GEN3_SID_MASK			GENMASK(3, 0)
+
+#define ADC5_GEN3_PERPH_CH			0x50
+#define ADC5_GEN3_CHAN_CONV_REQ			BIT(7)
+
+#define ADC5_GEN3_TIMER_SEL			0x51
+#define ADC5_GEN3_TIME_IMMEDIATE		0x1
+
+#define ADC5_GEN3_DIG_PARAM			0x52
+#define ADC5_GEN3_DIG_PARAM_CAL_SEL_MASK	GENMASK(5, 4)
+#define ADC5_GEN3_DIG_PARAM_DEC_RATIO_SEL_MASK	GENMASK(3, 2)
+
+#define ADC5_GEN3_FAST_AVG			0x53
+#define ADC5_GEN3_FAST_AVG_CTL_EN		BIT(7)
+#define ADC5_GEN3_FAST_AVG_CTL_SAMPLES_MASK	GENMASK(2, 0)
+
+#define ADC5_GEN3_ADC_CH_SEL_CTL		0x54
+#define ADC5_GEN3_DELAY_CTL			0x55
+#define ADC5_GEN3_HW_SETTLE_DELAY_MASK		GENMASK(3, 0)
+
+#define ADC5_GEN3_CH_EN				0x56
+#define ADC5_GEN3_HIGH_THR_INT_EN		BIT(1)
+#define ADC5_GEN3_LOW_THR_INT_EN		BIT(0)
+
+#define ADC5_GEN3_LOW_THR0			0x57
+#define ADC5_GEN3_LOW_THR1			0x58
+#define ADC5_GEN3_HIGH_THR0			0x59
+#define ADC5_GEN3_HIGH_THR1			0x5a
+
+#define ADC5_GEN3_CH_DATA0(channel)	(0x5c + (channel) * 2)
+#define ADC5_GEN3_CH_DATA1(channel)	(0x5d + (channel) * 2)
+
+#define ADC5_GEN3_CONV_REQ			0xe5
+#define ADC5_GEN3_CONV_REQ_REQ			BIT(0)
+
+#define ADC5_GEN3_VIRTUAL_SID_MASK			GENMASK(15, 8)
+#define ADC5_GEN3_CHANNEL_MASK			GENMASK(7, 0)
+#define V_CHAN(x)		\
+	(FIELD_PREP(ADC5_GEN3_VIRTUAL_SID_MASK, (x).sid) | (x).channel)	\
+
+enum adc5_cal_method {
+	ADC5_NO_CAL = 0,
+	ADC5_RATIOMETRIC_CAL,
+	ADC5_ABSOLUTE_CAL
+};
+
+enum adc5_time_select {
+	MEAS_INT_DISABLE = 0,
+	MEAS_INT_IMMEDIATE,
+	MEAS_INT_50MS,
+	MEAS_INT_100MS,
+	MEAS_INT_1S,
+	MEAS_INT_NONE,
+};
+
+struct adc5_sdam_data {
+	u16			base_addr;
+	const char		*irq_name;
+	int			irq;
+};
+
+/**
+ * struct adc5_channel_prop - ADC channel property.
+ * @channel: channel number, refer to the channel list.
+ * @cal_method: calibration method.
+ * @decimation: sampling rate supported for the channel.
+ * @sid: slave id of PMIC owning the channel.
+ * @prescale: channel scaling performed on the input signal.
+ * @hw_settle_time: the time between AMUX being configured and the
+ *	start of conversion.
+ * @avg_samples: ability to provide single result from the ADC
+ *	that is an average of multiple measurements.
+ * @sdam_index: Index for which SDAM this channel is on.
+ * @scale_fn_type: Represents the scaling function to convert voltage
+ *	physical units desired by the client for the channel.
+ * @label: Channel name used in device tree.
+ * @chip: pointer to top-level ADC device structure.
+ * @adc_tm: indicates if the channel is used for TM measurements.
+ * @tm_chan_index: TM channel number used (ranging from 1-7).
+ * @timer: time period of recurring TM measurement.
+ * @tzd: pointer to thermal device corresponding to TM channel.
+ * @high_thr_en: TM high threshold crossing detection enabled.
+ * @low_thr_en: TM low threshold crossing detection enabled.
+ * @last_temp: last temperature that caused threshold violation,
+ *	or a thermal TM channel.
+ * @last_temp_set: indicates if last_temp is stored.
+ */
+struct adc5_channel_prop {
+	unsigned int			channel;
+	enum adc5_cal_method		cal_method;
+	unsigned int			decimation;
+	unsigned int			sid;
+	unsigned int			prescale;
+	unsigned int			hw_settle_time;
+	unsigned int			avg_samples;
+	unsigned int			sdam_index;
+
+	enum vadc_scale_fn_type		scale_fn_type;
+	const char			*label;
+
+	struct adc5_chip		*chip;
+	/* TM(thermal monitoring related) properties */
+	bool				adc_tm;
+	unsigned int			tm_chan_index;
+	unsigned int			timer;
+	struct thermal_zone_device	*tzd;
+	bool				high_thr_en;
+	bool				low_thr_en;
+	int				last_temp;
+	bool				last_temp_set;
+};
+
+/**
+ * struct adc5_chip - ADC private structure.
+ * @regmap: SPMI ADC5 Gen3 peripheral register map field.
+ * @dev: SPMI ADC5 Gen3 device.
+ * @base: pointer to array of ADC peripheral base and interrupt.
+ * @num_sdams: number of SDAMs (Shared Direct Access Memory Module) being used.
+ * @nchannels: number of ADC channels.
+ * @chan_props: array of ADC channel properties.
+ * @iio_chans: array of IIO channels specification.
+ * @complete: ADC result notification after interrupt is received.
+ * @lock: ADC lock for access to the peripheral, to prevent concurrent
+ * requests from multiple clients.
+ * @data: software configuration data.
+ * @n_tm_channels: number of ADC channels used for TM measurements.
+ * @tm_handler_work: scheduled work for handling TM threshold violation.
+ */
+struct adc5_chip {
+	struct regmap			*regmap;
+	struct device			*dev;
+	struct adc5_sdam_data		*base;
+	unsigned int			num_sdams;
+	unsigned int			nchannels;
+	struct adc5_channel_prop	*chan_props;
+	struct iio_chan_spec		*iio_chans;
+	struct completion		complete;
+	struct mutex			lock;
+	const struct adc5_data		*data;
+	/* TM properties */
+	unsigned int			n_tm_channels;
+	struct work_struct		tm_handler_work;
+};
+
+static int adc5_gen3_read(struct adc5_chip *adc, unsigned int sdam_index,
+				u16 offset, u8 *data, int len)
+{
+	return regmap_bulk_read(adc->regmap, adc->base[sdam_index].base_addr + offset, data, len);
+}
+
+static int adc5_gen3_write(struct adc5_chip *adc, unsigned int sdam_index,
+				u16 offset, u8 *data, int len)
+{
+	return regmap_bulk_write(adc->regmap, adc->base[sdam_index].base_addr + offset, data, len);
+}
+
+static int adc5_gen3_read_voltage_data(struct adc5_chip *adc, u16 *data, u8 sdam_index)
+{
+	int ret;
+	u8 rslt[2];
+
+	ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_CH_DATA0(0), rslt, 2);
+	if (ret)
+		return ret;
+
+	*data = get_unaligned_le16(rslt);
+
+	if (*data == ADC5_USR_DATA_CHECK) {
+		dev_err(adc->dev, "Invalid data:%#x\n", *data);
+		return -EINVAL;
+	}
+
+	dev_dbg(adc->dev, "voltage raw code:%#x\n", *data);
+
+	return 0;
+}
+
+static void adc5_gen3_update_dig_param(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop, u8 *data)
+{
+	/* Update calibration select and decimation ratio select*/
+	*data &= ~(ADC5_GEN3_DIG_PARAM_CAL_SEL_MASK | ADC5_GEN3_DIG_PARAM_DEC_RATIO_SEL_MASK);
+	*data |= FIELD_PREP(ADC5_GEN3_DIG_PARAM_CAL_SEL_MASK, prop->cal_method);
+	*data |= FIELD_PREP(ADC5_GEN3_DIG_PARAM_DEC_RATIO_SEL_MASK, prop->decimation);
+}
+
+# define ADC5_GEN3_READ_CONFIG_REGS 7
+
+static int adc5_gen3_configure(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop)
+{
+	u8 sdam_index = prop->sdam_index;
+	u8 conv_req = 0;
+	u8 buf[ADC5_GEN3_READ_CONFIG_REGS];
+	int ret;
+
+	/* Reserve channel 0 of first SDAM for immediate conversions */
+	if (prop->adc_tm)
+		sdam_index = 0;
+
+	ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret)
+		return ret;
+
+	/* Write SID */
+	buf[0] = FIELD_PREP(ADC5_GEN3_SID_MASK, prop->sid);
+
+	/*
+	 * Use channel 0 by default for immediate conversion and
+	 * to indicate there is an actual conversion request
+	 */
+	buf[1] = ADC5_GEN3_CHAN_CONV_REQ | 0;
+
+	buf[2] = ADC5_GEN3_TIME_IMMEDIATE;
+
+	/* Digital param selection */
+	adc5_gen3_update_dig_param(adc, prop, &buf[3]);
+
+	/* Update fast average sample value */
+	buf[4] &= ~ADC5_GEN3_FAST_AVG_CTL_SAMPLES_MASK;
+	buf[4] |= prop->avg_samples | ADC5_GEN3_FAST_AVG_CTL_EN;
+
+	/* Select ADC channel */
+	buf[5] = prop->channel;
+
+	/* Select HW settle delay for channel */
+	buf[6] = FIELD_PREP(ADC5_GEN3_HW_SETTLE_DELAY_MASK, prop->hw_settle_time);
+
+	reinit_completion(&adc->complete);
+
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret)
+		return ret;
+
+	conv_req = ADC5_GEN3_CONV_REQ_REQ;
+	return adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &conv_req, 1);
+}
+
+/**
+ * Worst case delay from PBS in readying handshake bit
+ * can be up to 15ms, when PBS is busy running other
+ * simultaneous transactions, while in the best case, it is
+ * already ready at this point. Assigning polling delay and
+ * retry count accordingly.
+ */
+
+#define ADC5_GEN3_HS_DELAY_MIN_US		100
+#define ADC5_GEN3_HS_DELAY_MAX_US		110
+#define ADC5_GEN3_HS_RETRY_COUNT		150
+
+static int adc5_gen3_poll_wait_hs(struct adc5_chip *adc,
+				unsigned int sdam_index)
+{
+	u8 conv_req = ADC5_GEN3_CONV_REQ_REQ;
+	u8 status = 0;
+	int ret, count;
+
+	for (count = 0; count < ADC5_GEN3_HS_RETRY_COUNT; count++) {
+		ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_HS, &status, 1);
+		if (ret)
+			return ret;
+
+		if (status == ADC5_GEN3_HS_READY) {
+			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_CONV_REQ,
+					&conv_req, 1);
+			if (ret)
+				return ret;
+
+			if (!conv_req)
+				return 0;
+		}
+
+		usleep_range(ADC5_GEN3_HS_DELAY_MIN_US,
+			ADC5_GEN3_HS_DELAY_MAX_US);
+	}
+
+	dev_err(adc->dev, "Setting HS ready bit timed out, status:%#x\n", status);
+	return -ETIMEDOUT;
+}
+
+/**
+ * Worst case delay from PBS for conversion time can be
+ * up to 500ms, when PBS has timed out twice, once for
+ * the initial attempt and once for a retry of the same
+ * transaction.
+ */
+
+#define ADC5_GEN3_CONV_TIMEOUT_MS	501
+
+static int adc5_gen3_do_conversion(struct adc5_chip *adc,
+			struct adc5_channel_prop *prop,
+			u16 *data_volt)
+{
+	u8 val, sdam_index = prop->sdam_index;
+	unsigned long rc;
+	int ret;
+
+	/* Reserve channel 0 of first SDAM for immediate conversions */
+	if (prop->adc_tm)
+		sdam_index = 0;
+
+	mutex_lock(&adc->lock);
+	ret = adc5_gen3_poll_wait_hs(adc, 0);
+	if (ret)
+		goto unlock;
+
+	ret = adc5_gen3_configure(adc, prop);
+	if (ret) {
+		dev_err(adc->dev, "ADC configure failed with %d\n", ret);
+		goto unlock;
+	}
+
+	/* No support for polling mode at present*/
+	rc = wait_for_completion_timeout(&adc->complete,
+					msecs_to_jiffies(ADC5_GEN3_CONV_TIMEOUT_MS));
+	if (!rc) {
+		dev_err(adc->dev, "Reading ADC channel %s timed out\n",
+			prop->label);
+		ret = -ETIMEDOUT;
+		goto unlock;
+	}
+
+	ret = adc5_gen3_read_voltage_data(adc, data_volt, sdam_index);
+	if (ret)
+		goto unlock;
+
+	val = BIT(0);
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_EOC_CLR, &val, 1);
+	if (ret)
+		goto unlock;
+
+	/* To indicate conversion request is only to clear a status */
+	val = 0;
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
+	if (ret)
+		goto unlock;
+
+	val = ADC5_GEN3_CONV_REQ_REQ;
+	ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
+
+unlock:
+	mutex_unlock(&adc->lock);
+
+	return ret;
+}
+
+static int get_sdam_from_irq(struct adc5_chip *adc, int irq)
+{
+	int i;
+
+	for (i = 0; i < adc->num_sdams; i++) {
+		if (adc->base[i].irq == irq)
+			return i;
+	}
+	return -ENOENT;
+}
+
+static irqreturn_t adc5_gen3_isr(int irq, void *dev_id)
+{
+	struct adc5_chip *adc = dev_id;
+	u8 status, tm_status[2], eoc_status, val;
+	int ret, sdam_num;
+
+	sdam_num = get_sdam_from_irq(adc, irq);
+	if (sdam_num < 0) {
+		dev_err(adc->dev, "adc irq %d not associated with an sdam\n", irq);
+		return IRQ_HANDLED;
+	}
+
+	ret = adc5_gen3_read(adc, sdam_num, ADC5_GEN3_STATUS1, &status, 1);
+	if (ret) {
+		dev_err(adc->dev, "adc read status1 failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	ret = adc5_gen3_read(adc, sdam_num, ADC5_GEN3_EOC_STS, &eoc_status, 1);
+	if (ret) {
+		dev_err(adc->dev, "adc read eoc status failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	if (status & ADC5_GEN3_STATUS1_CONV_FAULT) {
+		dev_err_ratelimited(adc->dev, "Unexpected conversion fault, status:%#x, eoc_status:%#x\n",
+				status, eoc_status);
+		val = ADC5_GEN3_CONV_ERR_CLR_REQ;
+		ret = adc5_gen3_write(adc, sdam_num, ADC5_GEN3_CONV_ERR_CLR, &val, 1);
+		if (ret < 0)
+			return IRQ_HANDLED;
+
+		/* To indicate conversion request is only to clear a status */
+		val = 0;
+		ret = adc5_gen3_write(adc, sdam_num, ADC5_GEN3_PERPH_CH, &val, 1);
+		if (ret < 0)
+			return IRQ_HANDLED;
+
+		val = ADC5_GEN3_CONV_REQ_REQ;
+		ret = adc5_gen3_write(adc, sdam_num, ADC5_GEN3_CONV_REQ, &val, 1);
+
+		return IRQ_HANDLED;
+	}
+
+	/* CHAN0 is the preconfigured channel for immediate conversion */
+	if (eoc_status & ADC5_GEN3_EOC_CHAN_0)
+		complete(&adc->complete);
+
+	ret = adc5_gen3_read(adc, sdam_num, ADC5_GEN3_TM_HIGH_STS, tm_status, 2);
+	if (ret) {
+		dev_err(adc->dev, "adc read TM status failed with %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	if (tm_status[0] || tm_status[1])
+		schedule_work(&adc->tm_handler_work);
+
+	dev_dbg(adc->dev, "Interrupt status:%#x, EOC status:%#x, high:%#x, low:%#x\n",
+			status, eoc_status, tm_status[0], tm_status[1]);
+
+	return IRQ_HANDLED;
+}
+
+static void tm_handler_work(struct work_struct *work)
+{
+	struct adc5_chip *adc = container_of(work, struct adc5_chip, tm_handler_work);
+	struct adc5_channel_prop *chan_prop;
+	u8 tm_status[2] = {0};
+	u8 buf[16] = {0};
+	u8 val;
+	int ret, i, sdam_index = -1;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		bool upper_set = false, lower_set = false;
+		int temp, offset;
+		u16 code = 0;
+
+		chan_prop = &adc->chan_props[i];
+		offset = chan_prop->tm_chan_index;
+
+		if (!chan_prop->adc_tm)
+			continue;
+
+		mutex_lock(&adc->lock);
+		if (chan_prop->sdam_index != sdam_index) {
+			sdam_index = chan_prop->sdam_index;
+			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS,
+					tm_status, 2);
+			if (ret) {
+				dev_err(adc->dev, "adc read TM status failed with %d\n", ret);
+				goto out;
+			}
+
+			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_TM_HIGH_STS_CLR,
+					tm_status, 2);
+			if (ret) {
+				dev_err(adc->dev, "adc write TM status failed with %d\n", ret);
+				goto out;
+			}
+
+			/* To indicate conversion request is only to clear a status */
+			val = 0;
+			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
+			if (ret) {
+				dev_err(adc->dev, "adc write status clear conv_req failed with %d\n",
+						ret);
+				goto out;
+			}
+
+			val = ADC5_GEN3_CONV_REQ_REQ;
+			ret = adc5_gen3_write(adc, sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
+			if (ret) {
+				dev_err(adc->dev, "adc write conv_req failed with %d\n", ret);
+				goto out;
+			}
+
+			ret = adc5_gen3_read(adc, sdam_index, ADC5_GEN3_CH_DATA0(0), buf,
+					sizeof(buf));
+			if (ret < 0) {
+				dev_err(adc->dev, "adc read data failed with %d\n", ret);
+				goto out;
+			}
+		}
+
+		if ((tm_status[0] & BIT(offset)) && (chan_prop->high_thr_en))
+			upper_set = true;
+
+		if ((tm_status[1] & BIT(offset)) && (chan_prop->low_thr_en))
+			lower_set = true;
+
+		mutex_unlock(&adc->lock);
+
+		if (!(upper_set || lower_set))
+			continue;
+
+		code = get_unaligned_le16(&buf[2 * offset]);
+		pr_debug("ADC_TM threshold code:%#x\n", code);
+
+		ret = qcom_adc5_hw_scale(chan_prop->scale_fn_type,
+			chan_prop->prescale, adc->data, code, &temp);
+		if (ret) {
+			dev_err(adc->dev, "Invalid temperature reading, ret = %d, code=%#x\n",
+					ret, code);
+			continue;
+		}
+
+		chan_prop->last_temp = temp;
+		chan_prop->last_temp_set = true;
+		thermal_zone_device_update(chan_prop->tzd, THERMAL_TRIP_VIOLATED);
+	}
+
+	return;
+
+out:
+	mutex_unlock(&adc->lock);
+}
+
+static int adc5_gen3_fwnode_xlate(struct iio_dev *indio_dev,
+				const struct fwnode_reference_args *iiospec)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	int i, v_channel;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		v_channel = V_CHAN(adc->chan_props[i]);
+		if (v_channel == iiospec->args[0])
+			return i;
+	}
+
+	return -ENOENT;
+}
+
+static int adc5_gen3_read_raw(struct iio_dev *indio_dev,
+			 struct iio_chan_spec const *chan, int *val, int *val2,
+			 long mask)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	struct adc5_channel_prop *prop;
+	u16 adc_code_volt;
+	int ret;
+
+	prop = &adc->chan_props[chan->address];
+
+	switch (mask) {
+	case IIO_CHAN_INFO_PROCESSED:
+		ret = adc5_gen3_do_conversion(adc, prop,
+					&adc_code_volt);
+		if (ret)
+			return ret;
+
+		ret = qcom_adc5_hw_scale(prop->scale_fn_type,
+			prop->prescale, adc->data,
+			adc_code_volt, val);
+		if (ret)
+			return ret;
+
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_RAW:
+		ret = adc5_gen3_do_conversion(adc, prop,
+					&adc_code_volt);
+		if (ret)
+			return ret;
+		*val = (int)adc_code_volt;
+		return IIO_VAL_INT;
+	default:
+		return -EINVAL;
+	}
+}
+
+static int adc5_gen3_read_label(struct iio_dev *indio_dev,
+			const struct iio_chan_spec *chan, char *label)
+{
+	struct adc5_chip *adc = iio_priv(indio_dev);
+	struct adc5_channel_prop *prop;
+
+	prop = &adc->chan_props[chan->address];
+	return sprintf(label, "%s\n", prop->label);
+}
+
+static const struct iio_info adc5_gen3_info = {
+	.read_raw = adc5_gen3_read_raw,
+	.read_label = adc5_gen3_read_label,
+	.fwnode_xlate = adc5_gen3_fwnode_xlate,
+};
+
+static int adc_tm_gen3_get_temp(struct thermal_zone_device *tz, int *temp)
+{
+	struct adc5_channel_prop *prop = tz->devdata;
+	struct adc5_chip *adc;
+	u16 adc_code_volt;
+	int ret;
+
+	if (!prop || !prop->chip)
+		return -EINVAL;
+
+	adc = prop->chip;
+
+	if (prop->last_temp_set) {
+		pr_debug("last_temp: %d\n", prop->last_temp);
+		prop->last_temp_set = false;
+		*temp = prop->last_temp;
+		return 0;
+	}
+
+	ret = adc5_gen3_do_conversion(adc, prop, &adc_code_volt);
+	if (ret < 0)
+		return ret;
+
+	return qcom_adc5_hw_scale(prop->scale_fn_type,
+		prop->prescale, adc->data,
+		adc_code_volt, temp);
+}
+
+static int _adc_tm5_gen3_disable_channel(struct adc5_channel_prop *prop)
+{
+	struct adc5_chip *adc = prop->chip;
+	int ret;
+	u8 val;
+
+	prop->high_thr_en = false;
+	prop->low_thr_en = false;
+
+	val = MEAS_INT_DISABLE;
+	ret = adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_TIMER_SEL, &val, 1);
+	if (ret)
+		return ret;
+
+	/* To indicate there is an actual conversion request */
+	val = ADC5_GEN3_CHAN_CONV_REQ | prop->tm_chan_index;
+	ret = adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_PERPH_CH, &val, 1);
+	if (ret)
+		return ret;
+
+	val = ADC5_GEN3_CONV_REQ_REQ;
+	return adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_CONV_REQ, &val, 1);
+}
+
+static int adc_tm5_gen3_disable_channel(struct adc5_channel_prop *prop)
+{
+	return _adc_tm5_gen3_disable_channel(prop);
+}
+
+# define ADC_TM5_GEN3_CONFIG_REGS 12
+
+static int adc_tm5_gen3_configure(struct adc5_channel_prop *prop,
+					int low_temp, int high_temp)
+{
+	struct adc5_chip *adc = prop->chip;
+	u8 conv_req = 0, buf[ADC_TM5_GEN3_CONFIG_REGS];
+	u16 adc_code;
+	int ret;
+
+	ret = adc5_gen3_poll_wait_hs(adc, prop->sdam_index);
+	if (ret < 0)
+		return ret;
+
+	ret = adc5_gen3_read(adc, prop->sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	/* Write SID */
+	buf[0] = FIELD_PREP(ADC5_GEN3_SID_MASK, prop->sid);
+
+	/*
+	 * Select TM channel and indicate there is an actual
+	 * conversion request
+	 */
+	buf[1] = ADC5_GEN3_CHAN_CONV_REQ | prop->tm_chan_index;
+
+	buf[2] = prop->timer;
+
+	/* Digital param selection */
+	adc5_gen3_update_dig_param(adc, prop, &buf[3]);
+
+	/* Update fast average sample value */
+	buf[4] &= ~ADC5_GEN3_FAST_AVG_CTL_SAMPLES_MASK;
+	buf[4] |= prop->avg_samples | ADC5_GEN3_FAST_AVG_CTL_EN;
+
+	/* Select ADC channel */
+	buf[5] = prop->channel;
+
+	/* Select HW settle delay for channel */
+	buf[6] = FIELD_PREP(ADC5_GEN3_HW_SETTLE_DELAY_MASK, prop->hw_settle_time);
+
+	/* High temperature corresponds to low voltage threshold */
+	if (high_temp != INT_MAX) {
+		prop->low_thr_en = true;
+		adc_code = qcom_adc_tm5_gen2_temp_res_scale(high_temp);
+		put_unaligned_le16(adc_code, &buf[8]);
+	} else {
+		prop->low_thr_en = false;
+	}
+
+	/* Low temperature corresponds to high voltage threshold */
+	if (low_temp != -INT_MAX) {
+		prop->high_thr_en = true;
+		adc_code = qcom_adc_tm5_gen2_temp_res_scale(low_temp);
+		put_unaligned_le16(adc_code, &buf[10]);
+	} else {
+		prop->high_thr_en = false;
+	}
+
+	buf[7] = 0;
+	if (prop->high_thr_en)
+		buf[7] |= ADC5_GEN3_HIGH_THR_INT_EN;
+	if (prop->low_thr_en)
+		buf[7] |= ADC5_GEN3_LOW_THR_INT_EN;
+
+	ret = adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_SID, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	conv_req = ADC5_GEN3_CONV_REQ_REQ;
+	return adc5_gen3_write(adc, prop->sdam_index, ADC5_GEN3_CONV_REQ, &conv_req, 1);
+}
+
+static int adc_tm5_gen3_set_trip_temp(struct thermal_zone_device *tz,
+					int low_temp, int high_temp)
+{
+	struct adc5_channel_prop *prop = tz->devdata;
+	struct adc5_chip *adc;
+	int ret;
+
+	if (!prop || !prop->chip)
+		return -EINVAL;
+
+	adc = prop->chip;
+
+	dev_dbg(adc->dev, "channel:%s, low_temp(mdegC):%d, high_temp(mdegC):%d\n",
+		prop->label, low_temp, high_temp);
+
+	mutex_lock(&adc->lock);
+	if (high_temp == INT_MAX && low_temp <= -INT_MAX)
+		ret = adc_tm5_gen3_disable_channel(prop);
+	else
+		ret = adc_tm5_gen3_configure(prop, low_temp, high_temp);
+	mutex_unlock(&adc->lock);
+
+	return ret;
+}
+
+static const struct thermal_zone_device_ops adc_tm_ops = {
+	.get_temp = adc_tm_gen3_get_temp,
+	.set_trips = adc_tm5_gen3_set_trip_temp,
+};
+
+static int adc_tm_register_tzd(struct adc5_chip *adc)
+{
+	unsigned int i, channel;
+	struct thermal_zone_device *tzd;
+
+	for (i = 0; i < adc->nchannels; i++) {
+		channel = V_CHAN(adc->chan_props[i]);
+
+		if (!adc->chan_props[i].adc_tm)
+			continue;
+		tzd = devm_thermal_of_zone_register(adc->dev, channel,
+			&adc->chan_props[i], &adc_tm_ops);
+
+		if (IS_ERR(tzd)) {
+			if (PTR_ERR(tzd) == -ENODEV) {
+				dev_warn(adc->dev, "thermal sensor on channel %d is not used\n",
+					 channel);
+				continue;
+			}
+
+			dev_err(adc->dev, "Error registering TZ zone:%ld for channel:%d\n",
+				PTR_ERR(tzd), adc->chan_props[i].channel);
+			return PTR_ERR(tzd);
+		}
+		adc->chan_props[i].tzd = tzd;
+	}
+
+	return 0;
+}
+
+static void adc5_gen3_disable(void *data)
+{
+	struct adc5_chip *adc = data;
+	int i;
+
+	if (adc->n_tm_channels)
+		cancel_work_sync(&adc->tm_handler_work);
+
+	for (i = 0; i < adc->num_sdams; i++)
+		free_irq(adc->base[i].irq, adc);
+
+	mutex_lock(&adc->lock);
+	/* Disable all available TM channels */
+	for (i = 0; i < adc->nchannels; i++) {
+		if (!adc->chan_props[i].adc_tm)
+			continue;
+		adc5_gen3_poll_wait_hs(adc, adc->chan_props[i].sdam_index);
+		_adc_tm5_gen3_disable_channel(&adc->chan_props[i]);
+	}
+
+	mutex_unlock(&adc->lock);
+}
+
+struct adc5_channels {
+	unsigned int prescale_index;
+	enum iio_chan_type type;
+	long info_mask;
+	enum vadc_scale_fn_type scale_fn_type;
+};
+
+/* In these definitions, _pre refers to an index into adc5_prescale_ratios. */
+#define ADC5_CHAN(_type, _mask, _pre, _scale)	\
+	{						\
+		.prescale_index = _pre,			\
+		.type = _type,				\
+		.info_mask = _mask,			\
+		.scale_fn_type = _scale,		\
+	},						\
+
+#define ADC5_CHAN_TEMP(_pre, _scale)		\
+	ADC5_CHAN(IIO_TEMP, BIT(IIO_CHAN_INFO_PROCESSED), _pre, _scale)	\
+
+#define ADC5_CHAN_VOLT(_pre, _scale)		\
+	ADC5_CHAN(IIO_VOLTAGE, BIT(IIO_CHAN_INFO_PROCESSED), _pre, _scale)	\
+
+#define ADC5_CHAN_CUR(_pre, _scale)		\
+	ADC5_CHAN(IIO_CURRENT, BIT(IIO_CHAN_INFO_PROCESSED), _pre, _scale)	\
+
+static const struct adc5_channels adc5_gen3_chans_pmic[ADC5_MAX_CHANNEL] = {
+	[ADC5_GEN3_REF_GND]		= ADC5_CHAN_VOLT(0, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_1P25VREF]		= ADC5_CHAN_VOLT(0, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_VPH_PWR]		= ADC5_CHAN_VOLT(1, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_VBAT_SNS_QBG]	= ADC5_CHAN_VOLT(1, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_USB_SNS_V_16]	= ADC5_CHAN_TEMP(8, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_VIN_DIV16_MUX]	= ADC5_CHAN_TEMP(8, SCALE_HW_CALIB_DEFAULT)
+	[ADC5_GEN3_DIE_TEMP]		= ADC5_CHAN_TEMP(0,
+						SCALE_HW_CALIB_PMIC_THERM_PM7)
+	[ADC5_GEN3_TEMP_ALARM_LITE]	= ADC5_CHAN_TEMP(0,
+						SCALE_HW_CALIB_PMIC_THERM_PM7)
+	[ADC5_GEN3_AMUX1_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX2_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX3_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX4_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX5_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX6_THM_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX1_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX2_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX3_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+	[ADC5_GEN3_AMUX4_GPIO_100K_PU]	= ADC5_CHAN_TEMP(0,
+					SCALE_HW_CALIB_THERM_100K_PU_PM7)
+};
+
+static int adc5_gen3_get_fw_channel_data(struct adc5_chip *adc,
+				    struct adc5_channel_prop *prop,
+				    struct fwnode_handle *fwnode,
+				    const struct adc5_data *data)
+{
+	const char *name = fwnode_get_name(fwnode);
+	const char *channel_name;
+	struct device *dev = adc->dev;
+	u32 chan, value, varr[2], sid = 0;
+	int ret, val;
+
+	ret = fwnode_property_read_u32(fwnode, "reg", &chan);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "invalid channel number %s\n", name);
+
+	/*
+	 * Value read from "reg" is virtual channel number
+	 * virtual channel number = sid << 8 | channel number
+	 */
+
+	sid = FIELD_GET(ADC5_GEN3_VIRTUAL_SID_MASK, chan);
+	chan = FIELD_GET(ADC5_GEN3_CHANNEL_MASK, chan);
+
+	if (chan > ADC5_GEN3_OFFSET_EXT2)
+		return dev_err_probe(dev, -EINVAL, "%s invalid channel number %d\n", name, chan);
+
+	prop->channel = chan;
+	prop->sid = sid;
+
+	ret = fwnode_property_read_string(fwnode, "label", &channel_name);
+	if (ret)
+		channel_name = name;
+	prop->label = channel_name;
+
+	prop->decimation = ADC5_DECIMATION_DEFAULT;
+	ret = fwnode_property_read_u32(fwnode, "qcom,decimation", &value);
+	if (!ret) {
+		ret = qcom_adc5_decimation_from_dt(value, data->decimation);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid decimation %d\n",
+				chan, value);
+		prop->decimation = ret;
+	}
+
+	prop->prescale = adc->data->adc_chans[prop->channel].prescale_index;
+	ret = fwnode_property_read_u32_array(fwnode, "qcom,pre-scaling", varr, 2);
+	if (!ret) {
+		ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid pre-scaling <%d %d>\n",
+				chan, varr[0], varr[1]);
+		prop->prescale = ret;
+	}
+
+	prop->hw_settle_time = VADC_DEF_HW_SETTLE_TIME;
+	ret = fwnode_property_read_u32(fwnode, "qcom,hw-settle-time", &value);
+	if (!ret) {
+		ret = qcom_adc5_hw_settle_time_from_dt(value,
+						data->hw_settle_1);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid hw-settle-time %d us\n",
+				chan, value);
+		prop->hw_settle_time = ret;
+	}
+
+	prop->avg_samples = VADC_DEF_AVG_SAMPLES;
+	ret = fwnode_property_read_u32(fwnode, "qcom,avg-samples", &value);
+	if (!ret) {
+		ret = qcom_adc5_avg_samples_from_dt(value);
+		if (ret < 0)
+			return dev_err_probe(dev, ret, "%#x invalid avg-samples %d\n",
+				chan, value);
+		prop->avg_samples = ret;
+	}
+
+	if (fwnode_property_read_bool(fwnode, "qcom,ratiometric"))
+		prop->cal_method = ADC5_RATIOMETRIC_CAL;
+	else
+		prop->cal_method = ADC5_ABSOLUTE_CAL;
+
+	prop->timer = MEAS_INT_IMMEDIATE;
+
+	prop->adc_tm = fwnode_property_read_bool(fwnode, "qcom,adc-tm");
+
+	if (prop->adc_tm) {
+		adc->n_tm_channels++;
+		if (adc->n_tm_channels > ((adc->num_sdams * 8) - 1))
+			return dev_err_probe(adc->dev, -EINVAL,
+				"Number of TM nodes %u greater than channels supported:%u\n",
+				adc->n_tm_channels, (adc->num_sdams * 8) - 1);
+
+		val = adc->n_tm_channels / 8;
+		prop->sdam_index = val;
+		prop->tm_chan_index = adc->n_tm_channels - (8*val);
+
+		prop->timer = MEAS_INT_1S;
+	}
+
+	return 0;
+}
+
+static const struct adc5_data adc5_gen3_data_pmic = {
+	.full_scale_code_volt = 0x70e4,
+	.adc_chans = adc5_gen3_chans_pmic,
+	.info = &adc5_gen3_info,
+	.decimation = (unsigned int [ADC5_DECIMATION_SAMPLES_MAX])
+				{85, 340, 1360},
+	.hw_settle_1 = (unsigned int [VADC_HW_SETTLE_SAMPLES_MAX])
+				{15, 100, 200, 300, 400, 500, 600, 700,
+				1000, 2000, 4000, 8000, 16000, 32000,
+				64000, 128000},
+};
+
+static const struct of_device_id adc5_match_table[] = {
+	{
+		.compatible = "qcom,spmi-adc5-gen3",
+		.data = &adc5_gen3_data_pmic,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, adc5_match_table);
+
+static int adc5_get_fw_data(struct adc5_chip *adc)
+{
+	const struct adc5_channels *adc_chan;
+	struct iio_chan_spec *iio_chan;
+	struct adc5_channel_prop *chan_props;
+	struct fwnode_handle *child;
+	unsigned int index = 0;
+	int ret;
+
+	adc->nchannels = device_get_child_node_count(adc->dev);
+	if (!adc->nchannels)
+		return -EINVAL;
+
+	adc->iio_chans = devm_kcalloc(adc->dev, adc->nchannels,
+				       sizeof(*adc->iio_chans), GFP_KERNEL);
+	if (!adc->iio_chans)
+		return -ENOMEM;
+
+	adc->chan_props = devm_kcalloc(adc->dev, adc->nchannels,
+					sizeof(*adc->chan_props), GFP_KERNEL);
+	if (!adc->chan_props)
+		return -ENOMEM;
+
+	chan_props = adc->chan_props;
+	adc->n_tm_channels = 0;
+	iio_chan = adc->iio_chans;
+	adc->data = device_get_match_data(adc->dev);
+	if (!adc->data)
+		adc->data = &adc5_gen3_data_pmic;
+
+	device_for_each_child_node(adc->dev, child) {
+		ret = adc5_gen3_get_fw_channel_data(adc, chan_props, child, adc->data);
+		if (ret < 0) {
+			fwnode_handle_put(child);
+			return ret;
+		}
+
+		chan_props->chip = adc;
+		chan_props->scale_fn_type =
+			adc->data->adc_chans[chan_props->channel].scale_fn_type;
+		adc_chan = &adc->data->adc_chans[chan_props->channel];
+		iio_chan->channel = V_CHAN(*chan_props);
+		iio_chan->info_mask_separate = adc_chan->info_mask;
+		iio_chan->type = adc_chan->type;
+		iio_chan->address = index;
+		iio_chan->indexed = 1;
+		iio_chan++;
+		chan_props++;
+		index++;
+	}
+
+	return 0;
+}
+
+static int adc5_gen3_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct iio_dev *indio_dev;
+	struct adc5_chip *adc;
+	struct regmap *regmap;
+	int ret, i;
+	u32 *reg;
+
+	regmap = dev_get_regmap(dev->parent, NULL);
+	if (!regmap)
+		return -ENODEV;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	adc = iio_priv(indio_dev);
+	adc->regmap = regmap;
+	adc->dev = dev;
+
+	ret = device_property_count_u32(dev, "reg");
+	if (ret < 0)
+		return ret;
+
+	adc->num_sdams = ret;
+
+	reg = kcalloc(adc->num_sdams, sizeof(u32), GFP_KERNEL);
+	if (!reg)
+		return -ENOMEM;
+
+	ret = device_property_read_u32_array(dev, "reg", reg, adc->num_sdams);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to read reg property, ret = %d\n", ret);
+
+	adc->base = devm_kcalloc(dev, adc->num_sdams, sizeof(*adc->base), GFP_KERNEL);
+	if (!adc->base)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, indio_dev);
+	init_completion(&adc->complete);
+	mutex_init(&adc->lock);
+
+	for (i = 0; i < adc->num_sdams; i++) {
+		adc->base[i].base_addr = reg[i];
+
+		adc->base[i].irq_name = devm_kasprintf(dev, GFP_KERNEL, "adc-sdam%d", i);
+		if (!adc->base[i].irq_name) {
+			kfree(reg);
+			ret = -ENOMEM;
+			goto err_irq;
+		}
+
+		ret = platform_get_irq_byname(pdev, adc->base[i].irq_name);
+		if (ret < 0) {
+			kfree(reg);
+			dev_err(dev, "Getting IRQ %d by name failed, ret = %d\n",
+					adc->base[i].irq, ret);
+			goto err_irq;
+		}
+		adc->base[i].irq = ret;
+
+		ret = request_irq(adc->base[i].irq, adc5_gen3_isr, 0, adc->base[i].irq_name, adc);
+		if (ret < 0) {
+			kfree(reg);
+			dev_err(dev, "Failed to request SDAM%d irq, ret = %d\n", i, ret);
+			goto err_irq;
+		}
+	}
+	kfree(reg);
+
+	ret = devm_add_action(dev, adc5_gen3_disable, adc);
+	if (ret < 0) {
+		dev_err(dev, "failed to register adc disablement devm action, %d\n", ret);
+		goto err_irq;
+	}
+
+	ret = adc5_get_fw_data(adc);
+	if (ret < 0) {
+		dev_err(dev, "adc get dt data failed, ret = %d\n", ret);
+		goto err_irq;
+	}
+
+	ret = adc_tm_register_tzd(adc);
+	if (ret < 0)
+		goto err_irq;
+
+	if (adc->n_tm_channels)
+		INIT_WORK(&adc->tm_handler_work, tm_handler_work);
+
+	indio_dev->name = pdev->name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &adc5_gen3_info;
+	indio_dev->channels = adc->iio_chans;
+	indio_dev->num_channels = adc->nchannels;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (!ret)
+		return 0;
+
+err_irq:
+	for (i = 0; i < adc->num_sdams; i++)
+		free_irq(adc->base[i].irq, adc);
+
+	return ret;
+}
+
+static struct platform_driver adc5_gen3_driver = {
+	.driver = {
+		.name = "qcom-spmi-adc5-gen3",
+		.of_match_table = adc5_match_table,
+	},
+	.probe = adc5_gen3_probe,
+};
+module_platform_driver(adc5_gen3_driver);
+
+MODULE_DESCRIPTION("Qualcomm Technologies Inc. PMIC5 Gen3 ADC driver");
+MODULE_LICENSE("GPL");
