diff mbox series

[v3,2/2] arm64: dts: qcom: ipq6018: enable sdhci node

Message ID 20240118133022.553339-3-amadeus@jmu.edu.cn
State Superseded
Headers show
Series arm64: dts: qcom: ipq6018: enable sdhci node | expand

Commit Message

Chukun Pan Jan. 18, 2024, 1:30 p.m. UTC
Enable mmc device found on ipq6018 devices.
This node supports both eMMC and SD cards.

Tested with:
  eMMC (HS200)
  SD Card (SDR50/SDR104)

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
---
 arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

Comments

Bjorn Andersson Jan. 27, 2024, 11:19 p.m. UTC | #1
On Thu, Jan 18, 2024 at 09:30:22PM +0800, Chukun Pan wrote:
> Enable mmc device found on ipq6018 devices.
> This node supports both eMMC and SD cards.
> 
> Tested with:
>   eMMC (HS200)
>   SD Card (SDR50/SDR104)
> 
> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
> ---
>  arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++
>  1 file changed, 19 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> index 322eced0b876..420c192bccd9 100644
> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
> @@ -441,6 +441,25 @@ dwc_1: usb@7000000 {
>  			};
>  		};
>  
> +		sdhc: mmc@7804000 {
> +			compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5";
> +			reg = <0x0 0x7804000 0x0 0x1000>,
> +			      <0x0 0x7805000 0x0 0x1000>;
> +			reg-names = "hc", "cqhci";
> +
> +			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +
> +			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
> +				 <&gcc GCC_SDCC1_APPS_CLK>,
> +				 <&xo>;
> +			clock-names = "iface", "core", "xo";
> +			resets = <&gcc GCC_SDCC1_BCR>;
> +			max-frequency = <192000000>;
> +			status = "disabled";

Subject and commit message says "enable", but this says disable. Could
you change this to "Add" instead?

Do you have a patch for any board where this is actually enabled?
Perhaps you missed a 3rd patch that enables this and uses the ipq6018_l2
regulator you add in patch 1?

Regards,
Bjorn

> +		};
> +
>  		blsp_dma: dma-controller@7884000 {
>  			compatible = "qcom,bam-v1.7.0";
>  			reg = <0x0 0x07884000 0x0 0x2b000>;
> -- 
> 2.25.1
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 322eced0b876..420c192bccd9 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -441,6 +441,25 @@  dwc_1: usb@7000000 {
 			};
 		};
 
+		sdhc: mmc@7804000 {
+			compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x0 0x7804000 0x0 0x1000>,
+			      <0x0 0x7805000 0x0 0x1000>;
+			reg-names = "hc", "cqhci";
+
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo>;
+			clock-names = "iface", "core", "xo";
+			resets = <&gcc GCC_SDCC1_BCR>;
+			max-frequency = <192000000>;
+			status = "disabled";
+		};
+
 		blsp_dma: dma-controller@7884000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x0 0x07884000 0x0 0x2b000>;