diff mbox series

[v4,2/6] arm64: dts: qcom: sdm845-db845c-navigation-mezzanine: remove disabled ov7251 camera

Message ID 20241230-topic-misc-dt-fixes-v4-2-1e6880e9dda3@linaro.org
State New
Headers show
Series arm64: dts: qcom: misc DT bindings check fixes | expand

Commit Message

Neil Armstrong Dec. 30, 2024, 12:44 p.m. UTC 
The ov7251node has bindings check errors in the endpoint, and the
camera node was disabled since the beginning. Even when switching the
node to okay, the endpoint description to the csiphy is missing along
with the csiphy parameters.

Drop the ov7251 camera entirely until it's properly described.

This obviously fixes:
sdm845-db845c-navigation-mezzanine.dtso: camera@60: port:endpoint:data-lanes: [0, 1] is too long
	from schema $id: http://devicetree.org/schemas/media/i2c/ovti,ov7251.yaml#

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 .../qcom/sdm845-db845c-navigation-mezzanine.dtso   | 42 ----------------------
 1 file changed, 42 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dtso b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dtso
index 0a87df806cafc8e726aacc07a772ca478d0ee3df..59970082da45203311146cc5249298f6188bf67a 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dtso
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c-navigation-mezzanine.dtso
@@ -79,45 +79,3 @@  ov8856_ep: endpoint {
 		};
 	};
 };
-
-&cci_i2c1 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	camera@60 {
-		compatible = "ovti,ov7251";
-
-		/* I2C address as per ov7251.txt linux documentation */
-		reg = <0x60>;
-
-		/* CAM3_RST_N */
-		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&cam3_default>;
-
-		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
-		clock-names = "xclk";
-		clock-frequency = <24000000>;
-
-		/*
-		 * The &vreg_s4a_1p8 trace always powered on.
-		 *
-		 * The 2.8V vdda-supply regulator is enabled when the
-		 * vreg_s4a_1p8 trace is pulled high.
-		 * It too is represented by a fixed regulator.
-		 *
-		 * No 1.2V vddd-supply regulator is used.
-		 */
-		vdddo-supply = <&vreg_lvs1a_1p8>;
-		vdda-supply = <&cam3_avdd_2v8>;
-
-		status = "disabled";
-
-		port {
-			ov7251_ep: endpoint {
-				data-lanes = <0 1>;
-/*				remote-endpoint = <&csiphy3_ep>; */
-			};
-		};
-	};
-};