diff mbox series

[RFC,2/9] arm64: dts: qcom: qrb5165-rb5: model the PMU of the QCA6391

Message ID 20240201155532.49707-3-brgl@bgdev.pl
State Superseded
Headers show
Series power: sequencing: implement the subsystem and add first users | expand

Commit Message

Bartosz Golaszewski Feb. 1, 2024, 3:55 p.m. UTC
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add a node for the PMU module of the QCA6391 present on the RB5 board.
Assign its LDO power outputs to the existing Bluetooth module. Add a
node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
the board's .dts and also make it consume the power outputs of the PMU.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 128 +++++++++++++++++++++--
 arch/arm64/boot/dts/qcom/sm8250.dtsi     |  10 ++
 2 files changed, 127 insertions(+), 11 deletions(-)

Comments

Bjorn Andersson Feb. 2, 2024, 4:34 a.m. UTC | #1
On Thu, Feb 01, 2024 at 04:55:25PM +0100, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add a node for the PMU module of the QCA6391 present on the RB5 board.
> Assign its LDO power outputs to the existing Bluetooth module. Add a
> node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
> the board's .dts and also make it consume the power outputs of the PMU.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 128 +++++++++++++++++++++--
>  arch/arm64/boot/dts/qcom/sm8250.dtsi     |  10 ++
>  2 files changed, 127 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> index cd0db4f31d4a..fab5bebafbad 100644
> --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> @@ -108,6 +108,87 @@ lt9611_3v3: lt9611-3v3 {
>  		regulator-always-on;
>  	};
>  
> +	qca6390_pmu: pmu@0 {
> +		compatible = "qcom,qca6390-pmu";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
> +
> +		vddaon-supply = <&vreg_s6a_0p95>;
> +		vddpmu-supply = <&vreg_s2f_0p95>;
> +		vddrfa1-supply = <&vreg_s2f_0p95>;
> +		vddrfa2-supply = <&vreg_s8c_1p3>;
> +		vddrfa3-supply = <&vreg_s5a_1p9>;
> +		vddpcie1-supply = <&vreg_s8c_1p3>;
> +		vddpcie2-supply = <&vreg_s5a_1p9>;
> +		vddio-supply = <&vreg_s4a_1p8>;
> +
> +		wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
> +		bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> +
> +		regulators {
> +			vreg_pmu_rfa_cmn: ldo0 {
> +				regulator-name = "vreg_pmu_rfa_cmn";
> +				regulator-min-microvolt = <760000>;
> +				regulator-max-microvolt = <840000>;

I'm still not convinced that the PMU has a set of LDOs, and looking at
your implementation you neither register these with the regulator
framework, nor provide any means of controlling the state or voltage of
these "regulators".

[..]
>  
>  &uart6 {
> @@ -1311,17 +1418,16 @@ &uart6 {
>  	bluetooth {
>  		compatible = "qcom,qca6390-bt";
>  
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&bt_en_state>;
> -
> -		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> -
> -		vddio-supply = <&vreg_s4a_1p8>;
> -		vddpmu-supply = <&vreg_s2f_0p95>;
> -		vddaon-supply = <&vreg_s6a_0p95>;
> -		vddrfa0p9-supply = <&vreg_s2f_0p95>;
> -		vddrfa1p3-supply = <&vreg_s8c_1p3>;
> -		vddrfa1p9-supply = <&vreg_s5a_1p9>;
> +		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> +		vddaon-supply = <&vreg_pmu_aon_0p59>;
> +		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> +		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> +		vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
> +		vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
> +		vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
> +		vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
> +		vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
> +		vddpcie1-supply = <&vreg_pmu_pcie_1p8>;

As I asked before, why does bluetooth suddenly care about PCIe supplies?

Regards,
Bjorn

>  	};
>  };
>  
> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> index 4d849e98bf9b..7cd21d4e7278 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> @@ -2203,6 +2203,16 @@ pcie0: pcie@1c00000 {
>  			dma-coherent;
>  
>  			status = "disabled";
> +
> +			pcieport0: pcie@0 {
> +				device_type = "pci";
> +				reg = <0x0 0x0 0x0 0x0 0x0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				ranges;
> +
> +				bus-range = <0x01 0xff>;
> +			};
>  		};
>  
>  		pcie0_phy: phy@1c06000 {
> -- 
> 2.40.1
>
Dmitry Baryshkov Feb. 2, 2024, 4:59 a.m. UTC | #2
On Fri, 2 Feb 2024 at 06:34, Bjorn Andersson <andersson@kernel.org> wrote:
>
> On Thu, Feb 01, 2024 at 04:55:25PM +0100, Bartosz Golaszewski wrote:
> > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >
> > Add a node for the PMU module of the QCA6391 present on the RB5 board.
> > Assign its LDO power outputs to the existing Bluetooth module. Add a
> > node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
> > the board's .dts and also make it consume the power outputs of the PMU.
> >
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > ---
> >  arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 128 +++++++++++++++++++++--
> >  arch/arm64/boot/dts/qcom/sm8250.dtsi     |  10 ++
> >  2 files changed, 127 insertions(+), 11 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> > index cd0db4f31d4a..fab5bebafbad 100644
> > --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> > +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> > @@ -108,6 +108,87 @@ lt9611_3v3: lt9611-3v3 {
> >               regulator-always-on;
> >       };
> >
> > +     qca6390_pmu: pmu@0 {
> > +             compatible = "qcom,qca6390-pmu";
> > +
> > +             pinctrl-names = "default";
> > +             pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
> > +
> > +             vddaon-supply = <&vreg_s6a_0p95>;
> > +             vddpmu-supply = <&vreg_s2f_0p95>;
> > +             vddrfa1-supply = <&vreg_s2f_0p95>;
> > +             vddrfa2-supply = <&vreg_s8c_1p3>;
> > +             vddrfa3-supply = <&vreg_s5a_1p9>;
> > +             vddpcie1-supply = <&vreg_s8c_1p3>;
> > +             vddpcie2-supply = <&vreg_s5a_1p9>;
> > +             vddio-supply = <&vreg_s4a_1p8>;
> > +
> > +             wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
> > +             bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > +
> > +             regulators {
> > +                     vreg_pmu_rfa_cmn: ldo0 {
> > +                             regulator-name = "vreg_pmu_rfa_cmn";
> > +                             regulator-min-microvolt = <760000>;
> > +                             regulator-max-microvolt = <840000>;
>
> I'm still not convinced that the PMU has a set of LDOs, and looking at
> your implementation you neither register these with the regulator
> framework, nor provide any means of controlling the state or voltage of
> these "regulators".

Please take a look at the description of VDD08_PMU_RFA_CMN and
VDD_PMU_AON_I pins in the spec (80-WL522-1, page 25). I'm not sure if
I'm allowed to quote it, so I won't. But the spec clearly describes
VDD_PMU_AON_I as 0.95V LDO input and VDD08_PMU_RFA_CMN as 0.8 LDO
output generated using that input. I think this proves that the
on-chip PMU has actual LDOs.

I must admit, I find this representation very verbose, but on the
other hand Bartosz is right, it represents actual hardware. Maybe we
can drop some of the properties of corresponding regulator blocks, as
we don't actually need them and they are internal properties of the
hardware.

>
> [..]
> >
> >  &uart6 {
> > @@ -1311,17 +1418,16 @@ &uart6 {
> >       bluetooth {
> >               compatible = "qcom,qca6390-bt";
> >
> > -             pinctrl-names = "default";
> > -             pinctrl-0 = <&bt_en_state>;
> > -
> > -             enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > -
> > -             vddio-supply = <&vreg_s4a_1p8>;
> > -             vddpmu-supply = <&vreg_s2f_0p95>;
> > -             vddaon-supply = <&vreg_s6a_0p95>;
> > -             vddrfa0p9-supply = <&vreg_s2f_0p95>;
> > -             vddrfa1p3-supply = <&vreg_s8c_1p3>;
> > -             vddrfa1p9-supply = <&vreg_s5a_1p9>;
> > +             vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> > +             vddaon-supply = <&vreg_pmu_aon_0p59>;
> > +             vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> > +             vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> > +             vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
> > +             vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
> > +             vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
> > +             vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
> > +             vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
> > +             vddpcie1-supply = <&vreg_pmu_pcie_1p8>;
>
> As I asked before, why does bluetooth suddenly care about PCIe supplies?

Power sequencing in the same spec describes that PCIe voltages should
be up even if only BT is being brought up. PMU itself handles
distributing voltages according to the actual load needs.

>
> Regards,
> Bjorn
>
> >       };
> >  };
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> > index 4d849e98bf9b..7cd21d4e7278 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> > @@ -2203,6 +2203,16 @@ pcie0: pcie@1c00000 {
> >                       dma-coherent;
> >
> >                       status = "disabled";
> > +
> > +                     pcieport0: pcie@0 {
> > +                             device_type = "pci";
> > +                             reg = <0x0 0x0 0x0 0x0 0x0>;
> > +                             #address-cells = <3>;
> > +                             #size-cells = <2>;
> > +                             ranges;
> > +
> > +                             bus-range = <0x01 0xff>;
> > +                     };
> >               };
> >
> >               pcie0_phy: phy@1c06000 {
> > --
> > 2.40.1
> >
>
Bartosz Golaszewski Feb. 2, 2024, 1:23 p.m. UTC | #3
On Fri, Feb 2, 2024 at 5:34 AM Bjorn Andersson <andersson@kernel.org> wrote:
>

[snip]

> > +
> > +             wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
> > +             bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > +
> > +             regulators {
> > +                     vreg_pmu_rfa_cmn: ldo0 {
> > +                             regulator-name = "vreg_pmu_rfa_cmn";
> > +                             regulator-min-microvolt = <760000>;
> > +                             regulator-max-microvolt = <840000>;
>
> I'm still not convinced that the PMU has a set of LDOs, and looking at
> your implementation you neither register these with the regulator
> framework, nor provide any means of controlling the state or voltage of
> these "regulators".
>

Why are you so fixated on the driver implementation matching the
device-tree 1:1? I asked that question before - what does it matter if
we use the regulator subsystem or not? This is just what HW there is.
What we do with that knowledge in C is irrelevant. Yes, I don't use
the regulator subsystem because it's unnecessary and would actually
get in the way of the power sequencing. But it doesn't change the fact
that the regulators *are* there so let's show them.

What isn't there is a "power sequencer device". This was the main
concern about Dmitry's implementation before. We must not have
"bt-pwrseq = <&...>;" -like properties in device-tree because there is
no device that this would represent. But there *are* LDO outputs of
the PMU which can be modelled and then used in C to retrieve the power
sequencer and this is what I'm proposing.

Bartosz

> [..]
> >
> >  &uart6 {
> > @@ -1311,17 +1418,16 @@ &uart6 {
> >       bluetooth {
> >               compatible = "qcom,qca6390-bt";
> >
> > -             pinctrl-names = "default";
> > -             pinctrl-0 = <&bt_en_state>;
> > -
> > -             enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > -
> > -             vddio-supply = <&vreg_s4a_1p8>;
> > -             vddpmu-supply = <&vreg_s2f_0p95>;
> > -             vddaon-supply = <&vreg_s6a_0p95>;
> > -             vddrfa0p9-supply = <&vreg_s2f_0p95>;
> > -             vddrfa1p3-supply = <&vreg_s8c_1p3>;
> > -             vddrfa1p9-supply = <&vreg_s5a_1p9>;
> > +             vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> > +             vddaon-supply = <&vreg_pmu_aon_0p59>;
> > +             vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> > +             vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> > +             vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
> > +             vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
> > +             vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
> > +             vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
> > +             vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
> > +             vddpcie1-supply = <&vreg_pmu_pcie_1p8>;
>
> As I asked before, why does bluetooth suddenly care about PCIe supplies?
>

Yes, I forgot to remove it, I'll do it next time.

Bartosz

[snip]
Bjorn Andersson Feb. 2, 2024, 4:09 p.m. UTC | #4
On Fri, Feb 02, 2024 at 06:59:48AM +0200, Dmitry Baryshkov wrote:
> On Fri, 2 Feb 2024 at 06:34, Bjorn Andersson <andersson@kernel.org> wrote:
> >
> > On Thu, Feb 01, 2024 at 04:55:25PM +0100, Bartosz Golaszewski wrote:
> > > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > >
> > > Add a node for the PMU module of the QCA6391 present on the RB5 board.
> > > Assign its LDO power outputs to the existing Bluetooth module. Add a
> > > node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
> > > the board's .dts and also make it consume the power outputs of the PMU.
> > >
> > > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > > ---
> > >  arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 128 +++++++++++++++++++++--
> > >  arch/arm64/boot/dts/qcom/sm8250.dtsi     |  10 ++
> > >  2 files changed, 127 insertions(+), 11 deletions(-)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> > > index cd0db4f31d4a..fab5bebafbad 100644
> > > --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> > > +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> > > @@ -108,6 +108,87 @@ lt9611_3v3: lt9611-3v3 {
> > >               regulator-always-on;
> > >       };
> > >
> > > +     qca6390_pmu: pmu@0 {
> > > +             compatible = "qcom,qca6390-pmu";
> > > +
> > > +             pinctrl-names = "default";
> > > +             pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
> > > +
> > > +             vddaon-supply = <&vreg_s6a_0p95>;
> > > +             vddpmu-supply = <&vreg_s2f_0p95>;
> > > +             vddrfa1-supply = <&vreg_s2f_0p95>;
> > > +             vddrfa2-supply = <&vreg_s8c_1p3>;
> > > +             vddrfa3-supply = <&vreg_s5a_1p9>;
> > > +             vddpcie1-supply = <&vreg_s8c_1p3>;
> > > +             vddpcie2-supply = <&vreg_s5a_1p9>;
> > > +             vddio-supply = <&vreg_s4a_1p8>;
> > > +
> > > +             wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
> > > +             bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > > +
> > > +             regulators {
> > > +                     vreg_pmu_rfa_cmn: ldo0 {
> > > +                             regulator-name = "vreg_pmu_rfa_cmn";
> > > +                             regulator-min-microvolt = <760000>;
> > > +                             regulator-max-microvolt = <840000>;
> >
> > I'm still not convinced that the PMU has a set of LDOs, and looking at
> > your implementation you neither register these with the regulator
> > framework, nor provide any means of controlling the state or voltage of
> > these "regulators".
> 
> Please take a look at the description of VDD08_PMU_RFA_CMN and
> VDD_PMU_AON_I pins in the spec (80-WL522-1, page 25). I'm not sure if
> I'm allowed to quote it, so I won't. But the spec clearly describes
> VDD_PMU_AON_I as 0.95V LDO input and VDD08_PMU_RFA_CMN as 0.8 LDO
> output generated using that input. I think this proves that the
> on-chip PMU has actual LDOs.
> 

You're correct, thank you for the pointer and clarification. I now agree
with you, the PMU consumes what I saw as the chip input supplies, and
based on WL_EN and BT_EN will provide power on pads, which are then
externally routed to respective block.

> I must admit, I find this representation very verbose, but on the
> other hand Bartosz is right, it represents actual hardware.

I agree, this is actual hardware.

> Maybe we
> can drop some of the properties of corresponding regulator blocks, as
> we don't actually need them and they are internal properties of the
> hardware.
> 

To me this really looks like a fancy "regulator-fixed" with multiple
inputs, two gpios and multiple outputs.

This would also imply that we don't need to invent the power sequence
framework to tie WiFi and BT to the PMU's state.

The PMU is a thing, so we can represent that in DeviceTree, it consumes
M input power rails, and two gpios, it provides N WiFi supplies and O BT
supplies (with some overlap between N and O). The WiFi node consumes its
N supplies, the BT node consumes its O supplies.

If any of the N regulators are requested enabled the qca6390-pmu driver
enables all M input rails, then enables WL_EN. If any of the O BT
regulators are requested enabled, the driver enables all M input rails,
then enables BT_EN.

> >
> > [..]
> > >
> > >  &uart6 {
> > > @@ -1311,17 +1418,16 @@ &uart6 {
> > >       bluetooth {
> > >               compatible = "qcom,qca6390-bt";
> > >
> > > -             pinctrl-names = "default";
> > > -             pinctrl-0 = <&bt_en_state>;
> > > -
> > > -             enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > > -
> > > -             vddio-supply = <&vreg_s4a_1p8>;
> > > -             vddpmu-supply = <&vreg_s2f_0p95>;
> > > -             vddaon-supply = <&vreg_s6a_0p95>;
> > > -             vddrfa0p9-supply = <&vreg_s2f_0p95>;
> > > -             vddrfa1p3-supply = <&vreg_s8c_1p3>;
> > > -             vddrfa1p9-supply = <&vreg_s5a_1p9>;
> > > +             vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> > > +             vddaon-supply = <&vreg_pmu_aon_0p59>;
> > > +             vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> > > +             vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> > > +             vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
> > > +             vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
> > > +             vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
> > > +             vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
> > > +             vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
> > > +             vddpcie1-supply = <&vreg_pmu_pcie_1p8>;
> >
> > As I asked before, why does bluetooth suddenly care about PCIe supplies?
> 
> Power sequencing in the same spec describes that PCIe voltages should
> be up even if only BT is being brought up. PMU itself handles
> distributing voltages according to the actual load needs.
> 

You're right, the power sequence diagram in the docs do indicate that
VDD13_PMU_PCIE_I and VDD19_PMU_PCIE_I should be enabled before either
WL_EN or BT_EN are driven high.

But I don't see anything stating that the output from the PMU
(VDD09_PMU_PCIE) in turn is fed to the bluetooth block.

Regards,
Bjorn

> >
> > Regards,
> > Bjorn
> >
> > >       };
> > >  };
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> > > index 4d849e98bf9b..7cd21d4e7278 100644
> > > --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> > > @@ -2203,6 +2203,16 @@ pcie0: pcie@1c00000 {
> > >                       dma-coherent;
> > >
> > >                       status = "disabled";
> > > +
> > > +                     pcieport0: pcie@0 {
> > > +                             device_type = "pci";
> > > +                             reg = <0x0 0x0 0x0 0x0 0x0>;
> > > +                             #address-cells = <3>;
> > > +                             #size-cells = <2>;
> > > +                             ranges;
> > > +
> > > +                             bus-range = <0x01 0xff>;
> > > +                     };
> > >               };
> > >
> > >               pcie0_phy: phy@1c06000 {
> > > --
> > > 2.40.1
> > >
> >
> 
> 
> -- 
> With best wishes
> Dmitry
Bjorn Andersson Feb. 2, 2024, 4:41 p.m. UTC | #5
On Fri, Feb 02, 2024 at 02:23:49PM +0100, Bartosz Golaszewski wrote:
> On Fri, Feb 2, 2024 at 5:34 AM Bjorn Andersson <andersson@kernel.org> wrote:
> >
> 
> [snip]
> 
> > > +
> > > +             wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
> > > +             bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > > +
> > > +             regulators {
> > > +                     vreg_pmu_rfa_cmn: ldo0 {
> > > +                             regulator-name = "vreg_pmu_rfa_cmn";
> > > +                             regulator-min-microvolt = <760000>;
> > > +                             regulator-max-microvolt = <840000>;
> >
> > I'm still not convinced that the PMU has a set of LDOs, and looking at
> > your implementation you neither register these with the regulator
> > framework, nor provide any means of controlling the state or voltage of
> > these "regulators".
> >
> 
> Why are you so fixated on the driver implementation matching the
> device-tree 1:1? I asked that question before - what does it matter if
> we use the regulator subsystem or not?

I'm sorry, I must have missed this question. I'm not questioning why the
DT needs to match the Linux implementation, I was really questioning if
the hardware you describe here existed.

> This is just what HW there is.
> What we do with that knowledge in C is irrelevant. Yes, I don't use
> the regulator subsystem because it's unnecessary and would actually
> get in the way of the power sequencing.

Then describe that in your commit messages.

> But it doesn't change the fact
> that the regulators *are* there so let's show them.
> 
> What isn't there is a "power sequencer device". This was the main
> concern about Dmitry's implementation before.

I don't agree. The concerns that I saw being raised with Dmitry's
proposed design was that he used connected the WiFi controller to the
QCA6391 using power-domains, etc.

> We must not have
> "bt-pwrseq = <&...>;" -like properties in device-tree because there is
> no device that this would represent. But there *are* LDO outputs of
> the PMU which can be modelled and then used in C to retrieve the power
> sequencer and this is what I'm proposing.
> 

Performing device-specific power sequences is extremely common, but we
so far don't have a separate abstraction of this because it's generally
not an matter external to any given device.

If we're going to introduce a power sequence framework, it needs to be
made very clear that it is there to solve the problem that you have
devices on separate busses that need to share that sequence.

This also implies that for most examples out there where we have a need
for doing "PCI power sequencing", I don't think we would use the
power-sequence framework.

Regards,
Bjorn

> Bartosz
> 
> > [..]
> > >
> > >  &uart6 {
> > > @@ -1311,17 +1418,16 @@ &uart6 {
> > >       bluetooth {
> > >               compatible = "qcom,qca6390-bt";
> > >
> > > -             pinctrl-names = "default";
> > > -             pinctrl-0 = <&bt_en_state>;
> > > -
> > > -             enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> > > -
> > > -             vddio-supply = <&vreg_s4a_1p8>;
> > > -             vddpmu-supply = <&vreg_s2f_0p95>;
> > > -             vddaon-supply = <&vreg_s6a_0p95>;
> > > -             vddrfa0p9-supply = <&vreg_s2f_0p95>;
> > > -             vddrfa1p3-supply = <&vreg_s8c_1p3>;
> > > -             vddrfa1p9-supply = <&vreg_s5a_1p9>;
> > > +             vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> > > +             vddaon-supply = <&vreg_pmu_aon_0p59>;
> > > +             vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> > > +             vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> > > +             vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
> > > +             vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
> > > +             vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
> > > +             vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
> > > +             vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
> > > +             vddpcie1-supply = <&vreg_pmu_pcie_1p8>;
> >
> > As I asked before, why does bluetooth suddenly care about PCIe supplies?
> >
> 
> Yes, I forgot to remove it, I'll do it next time.
> 
> Bartosz
> 
> [snip]
Bjorn Andersson Feb. 2, 2024, 4:47 p.m. UTC | #6
On Thu, Feb 01, 2024 at 04:55:25PM +0100, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add a node for the PMU module of the QCA6391 present on the RB5 board.
> Assign its LDO power outputs to the existing Bluetooth module. Add a
> node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
> the board's .dts and also make it consume the power outputs of the PMU.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 128 +++++++++++++++++++++--
>  arch/arm64/boot/dts/qcom/sm8250.dtsi     |  10 ++
>  2 files changed, 127 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> index cd0db4f31d4a..fab5bebafbad 100644
> --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> @@ -108,6 +108,87 @@ lt9611_3v3: lt9611-3v3 {
>  		regulator-always-on;
>  	};
>  
> +	qca6390_pmu: pmu@0 {

The node doesn't have an address, so why does it have a unit address?
Also, the node isn't referenced, so please skip the label.

> +		compatible = "qcom,qca6390-pmu";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
> +
> +		vddaon-supply = <&vreg_s6a_0p95>;
> +		vddpmu-supply = <&vreg_s2f_0p95>;
> +		vddrfa1-supply = <&vreg_s2f_0p95>;
> +		vddrfa2-supply = <&vreg_s8c_1p3>;
> +		vddrfa3-supply = <&vreg_s5a_1p9>;
> +		vddpcie1-supply = <&vreg_s8c_1p3>;
> +		vddpcie2-supply = <&vreg_s5a_1p9>;
> +		vddio-supply = <&vreg_s4a_1p8>;

So, after studying the datasheet for this. The names of the pins seems
to come from the existing binding(s). As you're introducing a new
binding (and driver) for qcom,qca6390-pmu, please use the pad names from
qca6390.

> +
> +		wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
> +		bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> +
> +		regulators {
> +			vreg_pmu_rfa_cmn: ldo0 {
> +				regulator-name = "vreg_pmu_rfa_cmn";
> +				regulator-min-microvolt = <760000>;
> +				regulator-max-microvolt = <840000>;

The min/max operating range of the regulator is something we provide in
the implementation, in DeviceTree you should specify the expected
operating voltage. Based on the TYP value this should be
regulator-min-microvolt = regulator-max-microvolt = 0.8V.

> +			};
> +
> +			vreg_pmu_aon_0p59: ldo1 {
> +				regulator-name = "vreg_pmu_aon_0p59";
> +				regulator-min-microvolt = <540000>;
> +				regulator-max-microvolt = <840000>;
> +			};
[..]
> @@ -1303,6 +1402,14 @@ sdc2_card_det_n: sd-card-det-n-state {
>  		function = "gpio";
>  		bias-pull-up;
>  	};
> +
> +	wlan_en_state: wlan-default-state {
> +		pins = "gpio20";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		output-low;

Please omit output-low here.

> +		bias-pull-up;

Why do you drive it low and pull it high? bias-disable sounds more
appropriate.

Regards,
Bjorn

> +	};
>  };
>  
>  &uart6 {
> @@ -1311,17 +1418,16 @@ &uart6 {
>  	bluetooth {
>  		compatible = "qcom,qca6390-bt";
>  
> -		pinctrl-names = "default";
> -		pinctrl-0 = <&bt_en_state>;
> -
> -		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
> -
> -		vddio-supply = <&vreg_s4a_1p8>;
> -		vddpmu-supply = <&vreg_s2f_0p95>;
> -		vddaon-supply = <&vreg_s6a_0p95>;
> -		vddrfa0p9-supply = <&vreg_s2f_0p95>;
> -		vddrfa1p3-supply = <&vreg_s8c_1p3>;
> -		vddrfa1p9-supply = <&vreg_s5a_1p9>;
> +		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> +		vddaon-supply = <&vreg_pmu_aon_0p59>;
> +		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> +		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> +		vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
> +		vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
> +		vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
> +		vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
> +		vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
> +		vddpcie1-supply = <&vreg_pmu_pcie_1p8>;
>  	};
>  };
>  
> diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> index 4d849e98bf9b..7cd21d4e7278 100644
> --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
> @@ -2203,6 +2203,16 @@ pcie0: pcie@1c00000 {
>  			dma-coherent;
>  
>  			status = "disabled";
> +
> +			pcieport0: pcie@0 {
> +				device_type = "pci";
> +				reg = <0x0 0x0 0x0 0x0 0x0>;
> +				#address-cells = <3>;
> +				#size-cells = <2>;
> +				ranges;
> +
> +				bus-range = <0x01 0xff>;
> +			};
>  		};
>  
>  		pcie0_phy: phy@1c06000 {
> -- 
> 2.40.1
>
Krzysztof Kozlowski Feb. 5, 2024, 7:51 a.m. UTC | #7
On 01/02/2024 16:55, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> Add a node for the PMU module of the QCA6391 present on the RB5 board.
> Assign its LDO power outputs to the existing Bluetooth module. Add a
> node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
> the board's .dts and also make it consume the power outputs of the PMU.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 128 +++++++++++++++++++++--
>  arch/arm64/boot/dts/qcom/sm8250.dtsi     |  10 ++
>  2 files changed, 127 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> index cd0db4f31d4a..fab5bebafbad 100644
> --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
> @@ -108,6 +108,87 @@ lt9611_3v3: lt9611-3v3 {
>  		regulator-always-on;
>  	};
>  
> +	qca6390_pmu: pmu@0 {

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index cd0db4f31d4a..fab5bebafbad 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -108,6 +108,87 @@  lt9611_3v3: lt9611-3v3 {
 		regulator-always-on;
 	};
 
+	qca6390_pmu: pmu@0 {
+		compatible = "qcom,qca6390-pmu";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
+
+		vddaon-supply = <&vreg_s6a_0p95>;
+		vddpmu-supply = <&vreg_s2f_0p95>;
+		vddrfa1-supply = <&vreg_s2f_0p95>;
+		vddrfa2-supply = <&vreg_s8c_1p3>;
+		vddrfa3-supply = <&vreg_s5a_1p9>;
+		vddpcie1-supply = <&vreg_s8c_1p3>;
+		vddpcie2-supply = <&vreg_s5a_1p9>;
+		vddio-supply = <&vreg_s4a_1p8>;
+
+		wlan-enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+				regulator-min-microvolt = <760000>;
+				regulator-max-microvolt = <840000>;
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+				regulator-min-microvolt = <540000>;
+				regulator-max-microvolt = <840000>;
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator_name = "vreg_pmu_wlcx_0p8";
+				regulator-min-microvolt = <760000>;
+				regulator-max-microvolt = <840000>;
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <890000>;
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <890000>;
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+				regulator-min-microvolt = <760000>;
+				regulator-max-microvolt = <840000>;
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+				regulator-min-microvolt = <1187000>;
+				regulator-max-microvolt = <1313000>;
+			};
+
+			vreg_pmu_rfa_1p7: ldo7 {
+				regulator_name = "vreg_pmu_rfa_1p7";
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <1890000>;
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator_name = "vreg_pmu_pcie_0p9";
+				regulator-min-microvolt = <870000>;
+				regulator-max-microvolt = <970000>;
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator_name = "vreg_pmu_pcie_1p8";
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <1890000>;
+			};
+		};
+	};
+
 	thermal-zones {
 		conn-thermal {
 			polling-delay-passive = <0>;
@@ -734,6 +815,24 @@  &pcie0_phy {
 	vdda-pll-supply = <&vreg_l9a_1p2>;
 };
 
+&pcieport0 {
+	wifi@0 {
+		compatible = "pci17cb,1101";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+		vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
+		vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
 &pcie1 {
 	status = "okay";
 };
@@ -1303,6 +1402,14 @@  sdc2_card_det_n: sd-card-det-n-state {
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	wlan_en_state: wlan-default-state {
+		pins = "gpio20";
+		function = "gpio";
+		drive-strength = <16>;
+		output-low;
+		bias-pull-up;
+	};
 };
 
 &uart6 {
@@ -1311,17 +1418,16 @@  &uart6 {
 	bluetooth {
 		compatible = "qcom,qca6390-bt";
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&bt_en_state>;
-
-		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
-
-		vddio-supply = <&vreg_s4a_1p8>;
-		vddpmu-supply = <&vreg_s2f_0p95>;
-		vddaon-supply = <&vreg_s6a_0p95>;
-		vddrfa0p9-supply = <&vreg_s2f_0p95>;
-		vddrfa1p3-supply = <&vreg_s8c_1p3>;
-		vddrfa1p9-supply = <&vreg_s5a_1p9>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+		vddrfa0-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa2-supply = <&vreg_pmu_rfa_1p7>;
+		vddpcie0-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1-supply = <&vreg_pmu_pcie_1p8>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 4d849e98bf9b..7cd21d4e7278 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -2203,6 +2203,16 @@  pcie0: pcie@1c00000 {
 			dma-coherent;
 
 			status = "disabled";
+
+			pcieport0: pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+
+				bus-range = <0x01 0xff>;
+			};
 		};
 
 		pcie0_phy: phy@1c06000 {