| Message ID | 20210727004118.2583774-1-mka@chromium.org |
|---|---|
| Headers | show |
| Series | usb: misc: Add onboard_usb_hub driver | expand |
Hi Matthias, On 09/08/2021 18:49, Matthias Kaehlcke wrote: > Hi Greg, > > Just wanted to check if this series is still on your radar. Is > there anything that blocks it from landing (further ACKs, ...)? > > Thanks > > Matthias > > On Mon, Jul 26, 2021 at 05:41:12PM -0700, Matthias Kaehlcke wrote: >> This series adds: >> - the onboard_usb_hub_driver >> - glue in the xhci-plat driver to create and destroy the >> onboard_usb_hub platform devices if needed >> - a device tree binding for the Realtek RTS5411 USB hub controller >> - device tree changes that add RTS5411 entries for the QCA SC7180 >> based boards trogdor and lazor >> - a couple of stubs for platform device functions to avoid >> unresolved symbols with certain kernel configs >> >> The main issue the driver addresses is that a USB hub needs to be >> powered before it can be discovered. For discrete onboard hubs (an >> example for such a hub is the Realtek RTS5411) this is often solved >> by supplying the hub with an 'always-on' regulator, which is kind >> of a hack. Some onboard hubs may require further initialization >> steps, like changing the state of a GPIO or enabling a clock, which >> requires even more hacks. This driver creates a platform device >> representing the hub which performs the necessary initialization. >> Currently it only supports switching on a single regulator, support >> for multiple regulators or other actions can be added as needed. >> Different initialization sequences can be supported based on the >> compatible string. >> >> Besides performing the initialization the driver can be configured >> to power the hub off during system suspend. This can help to extend >> battery life on battery powered devices which have no requirements >> to keep the hub powered during suspend. The driver can also be >> configured to leave the hub powered when a wakeup capable USB device >> is connected when suspending, and power it off otherwise. >> >> Changes in v15: >> - adjusted dependencies of USB_DWC3_CORE to make sure it can only >> be enabled when at least one of USB_DWC3_HOST, USB_DWC3_GADGET >> or USB_DWC3_DUAL_ROLE is selectable >> >> Changes in v14: >> - rebased on top of v5.14-rc1 >> - dropped DT binding patch which landed in v5.13 >> >> Changes in v13: >> - added patch "usb: Specify dependency on USB_XHCI_PLATFORM with >> 'depends on'" to the series to avoid Kconfig conflicts >> - added patch "arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM" >> to the series to keep effective defconfig unchanged >> >> Changes in v12: >> - onboard_hub driver: use IS_ENABLED(CONFIG_USB_ONBOARD_HUB_MODULE) >> in onboard_hub.h to also check for the driver built as module >> - onboard_hub_driver: include onboard_hub.h again to make sure there >> are prototype declarations for the public functions >> >> Changes in v11: >> - support multiple onboard hubs connected to the same parent >> - don't include ‘onboard_hub.h’ from the onboard hub driver >> >> Changes in v10: >> - always use of_is_onboard_usb_hub() stub unless ONBOARD_USB_HUB=y/m >> - keep 'regulator-boot-on' property for pp3300_hub >> >> Changes in v9: >> - added dependency on ONBOARD_USB_HUB (or !!ONBOARD_USB_HUB) to >> USB_PLATFORM_XHCI >> >> Changes in v7: >> - updated DT binding >> - series rebased on qcom/arm64-for-5.13 >> >> Changes in v6: >> - updated summary >> >> Changes in v5: >> - cover letter added >> >> Matthias Kaehlcke (6): >> usb: misc: Add onboard_usb_hub driver >> of/platform: Add stubs for of_platform_device_create/destroy() >> arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM >> usb: Specify dependencies on USB_XHCI_PLATFORM with 'depends on' >> usb: host: xhci-plat: Create platform device for onboard hubs in >> probe() >> arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub >> >> .../sysfs-bus-platform-onboard-usb-hub | 8 + >> MAINTAINERS | 7 + >> .../boot/dts/qcom/sc7180-trogdor-lazor-r0.dts | 19 +- >> .../boot/dts/qcom/sc7180-trogdor-lazor-r1.dts | 12 +- >> .../arm64/boot/dts/qcom/sc7180-trogdor-r1.dts | 19 +- >> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 19 +- >> arch/arm64/configs/defconfig | 1 + >> drivers/usb/cdns3/Kconfig | 2 +- >> drivers/usb/dwc3/Kconfig | 5 +- >> drivers/usb/host/Kconfig | 5 +- These Kconfig changes are causing the resulting .config to be different. For example, if I start with omap2plus_defconfig, the resulting .config before and after your series is different as shown below :/work/linux$ diff /tmp/.config .config 1902d1901 < # CONFIG_HISI_HIKEY_USB is not set 4992c4991 < CONFIG_USB_XHCI_PLATFORM=m --- > # CONFIG_USB_XHCI_PLATFORM is not set 5073,5075c5072 < # CONFIG_USB_DWC3_HOST is not set < # CONFIG_USB_DWC3_GADGET is not set < CONFIG_USB_DWC3_DUAL_ROLE=y --- > CONFIG_USB_DWC3_GADGET=y 5173a5171 > # CONFIG_USB_ONBOARD_HUB is not set 5285c5283 < CONFIG_USB_ROLE_SWITCH=m --- > # CONFIG_USB_ROLE_SWITCH is not set I would expect the same issues for multi_v7_defconfig and multi_v8_defconfig as well. I'm ok to update the relevant defconfigs files so that the resulting .config is identical to before your series. Thanks! -- cheers, -roger
On 11/08/2021 15:38, Roger Quadros wrote: > Hi Matthias, > > On 09/08/2021 18:49, Matthias Kaehlcke wrote: >> Hi Greg, >> >> Just wanted to check if this series is still on your radar. Is >> there anything that blocks it from landing (further ACKs, ...)? >> >> Thanks >> >> Matthias >> >> On Mon, Jul 26, 2021 at 05:41:12PM -0700, Matthias Kaehlcke wrote: >>> This series adds: >>> - the onboard_usb_hub_driver >>> - glue in the xhci-plat driver to create and destroy the >>> onboard_usb_hub platform devices if needed >>> - a device tree binding for the Realtek RTS5411 USB hub controller >>> - device tree changes that add RTS5411 entries for the QCA SC7180 >>> based boards trogdor and lazor >>> - a couple of stubs for platform device functions to avoid >>> unresolved symbols with certain kernel configs >>> >>> The main issue the driver addresses is that a USB hub needs to be >>> powered before it can be discovered. For discrete onboard hubs (an >>> example for such a hub is the Realtek RTS5411) this is often solved >>> by supplying the hub with an 'always-on' regulator, which is kind >>> of a hack. Some onboard hubs may require further initialization >>> steps, like changing the state of a GPIO or enabling a clock, which >>> requires even more hacks. This driver creates a platform device >>> representing the hub which performs the necessary initialization. >>> Currently it only supports switching on a single regulator, support >>> for multiple regulators or other actions can be added as needed. >>> Different initialization sequences can be supported based on the >>> compatible string. >>> >>> Besides performing the initialization the driver can be configured >>> to power the hub off during system suspend. This can help to extend >>> battery life on battery powered devices which have no requirements >>> to keep the hub powered during suspend. The driver can also be >>> configured to leave the hub powered when a wakeup capable USB device >>> is connected when suspending, and power it off otherwise. >>> >>> Changes in v15: >>> - adjusted dependencies of USB_DWC3_CORE to make sure it can only >>> be enabled when at least one of USB_DWC3_HOST, USB_DWC3_GADGET >>> or USB_DWC3_DUAL_ROLE is selectable >>> >>> Changes in v14: >>> - rebased on top of v5.14-rc1 >>> - dropped DT binding patch which landed in v5.13 >>> >>> Changes in v13: >>> - added patch "usb: Specify dependency on USB_XHCI_PLATFORM with >>> 'depends on'" to the series to avoid Kconfig conflicts >>> - added patch "arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM" >>> to the series to keep effective defconfig unchanged >>> >>> Changes in v12: >>> - onboard_hub driver: use IS_ENABLED(CONFIG_USB_ONBOARD_HUB_MODULE) >>> in onboard_hub.h to also check for the driver built as module >>> - onboard_hub_driver: include onboard_hub.h again to make sure there >>> are prototype declarations for the public functions >>> >>> Changes in v11: >>> - support multiple onboard hubs connected to the same parent >>> - don't include ‘onboard_hub.h’ from the onboard hub driver >>> >>> Changes in v10: >>> - always use of_is_onboard_usb_hub() stub unless ONBOARD_USB_HUB=y/m >>> - keep 'regulator-boot-on' property for pp3300_hub >>> >>> Changes in v9: >>> - added dependency on ONBOARD_USB_HUB (or !!ONBOARD_USB_HUB) to >>> USB_PLATFORM_XHCI >>> >>> Changes in v7: >>> - updated DT binding >>> - series rebased on qcom/arm64-for-5.13 >>> >>> Changes in v6: >>> - updated summary >>> >>> Changes in v5: >>> - cover letter added >>> >>> Matthias Kaehlcke (6): >>> usb: misc: Add onboard_usb_hub driver >>> of/platform: Add stubs for of_platform_device_create/destroy() >>> arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM >>> usb: Specify dependencies on USB_XHCI_PLATFORM with 'depends on' >>> usb: host: xhci-plat: Create platform device for onboard hubs in >>> probe() >>> arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub >>> >>> .../sysfs-bus-platform-onboard-usb-hub | 8 + >>> MAINTAINERS | 7 + >>> .../boot/dts/qcom/sc7180-trogdor-lazor-r0.dts | 19 +- >>> .../boot/dts/qcom/sc7180-trogdor-lazor-r1.dts | 12 +- >>> .../arm64/boot/dts/qcom/sc7180-trogdor-r1.dts | 19 +- >>> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 19 +- >>> arch/arm64/configs/defconfig | 1 + >>> drivers/usb/cdns3/Kconfig | 2 +- >>> drivers/usb/dwc3/Kconfig | 5 +- >>> drivers/usb/host/Kconfig | 5 +- > > These Kconfig changes are causing the resulting .config to be different. > For example, if I start with omap2plus_defconfig, the resulting .config > before and after your series is different as shown below > > :/work/linux$ diff /tmp/.config .config > 1902d1901 > < # CONFIG_HISI_HIKEY_USB is not set > 4992c4991 > < CONFIG_USB_XHCI_PLATFORM=m > --- >> # CONFIG_USB_XHCI_PLATFORM is not set > 5073,5075c5072 > < # CONFIG_USB_DWC3_HOST is not set > < # CONFIG_USB_DWC3_GADGET is not set > < CONFIG_USB_DWC3_DUAL_ROLE=y > --- >> CONFIG_USB_DWC3_GADGET=y > 5173a5171 >> # CONFIG_USB_ONBOARD_HUB is not set > 5285c5283 > < CONFIG_USB_ROLE_SWITCH=m > --- >> # CONFIG_USB_ROLE_SWITCH is not set > > I would expect the same issues for multi_v7_defconfig and multi_v8_defconfig as well. Sorry I meant defconfig for arm64, not multi_v8_defconfig. I checked that for arm64 defconfig it is ok. > I'm ok to update the relevant defconfigs files so that the resulting .config is identical to > before your series. Thanks! With the below patch you can fix it for omap2plus_defconfig and multi_v7_defconfig. diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index d9abaae118dd..8c175ab37377 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -787,6 +787,7 @@ CONFIG_SND_AUDIO_GRAPH_CARD=m CONFIG_USB=y CONFIG_USB_OTG=y CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PLATFORM=y CONFIG_USB_XHCI_MVEBU=y CONFIG_USB_XHCI_TEGRA=m CONFIG_USB_EHCI_HCD=y diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 2ac2418084ab..a015fb04fa25 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -562,6 +562,7 @@ CONFIG_USB=m CONFIG_USB_ANNOUNCE_NEW_DEVICES=y CONFIG_USB_MON=m CONFIG_USB_XHCI_HCD=m +CONFIG_USB_XHCI_PLATFORM=m CONFIG_USB_EHCI_HCD=m CONFIG_USB_OHCI_HCD=m CONFIG_USB_ACM=m -- cheers, -roger
Hi Roger, On Wed, Aug 11, 2021 at 03:56:15PM +0300, Roger Quadros wrote: > > > On 11/08/2021 15:38, Roger Quadros wrote: > > Hi Matthias, > > > > On 09/08/2021 18:49, Matthias Kaehlcke wrote: > >> Hi Greg, > >> > >> Just wanted to check if this series is still on your radar. Is > >> there anything that blocks it from landing (further ACKs, ...)? > >> > >> Thanks > >> > >> Matthias > >> > >> On Mon, Jul 26, 2021 at 05:41:12PM -0700, Matthias Kaehlcke wrote: > >>> This series adds: > >>> - the onboard_usb_hub_driver > >>> - glue in the xhci-plat driver to create and destroy the > >>> onboard_usb_hub platform devices if needed > >>> - a device tree binding for the Realtek RTS5411 USB hub controller > >>> - device tree changes that add RTS5411 entries for the QCA SC7180 > >>> based boards trogdor and lazor > >>> - a couple of stubs for platform device functions to avoid > >>> unresolved symbols with certain kernel configs > >>> > >>> The main issue the driver addresses is that a USB hub needs to be > >>> powered before it can be discovered. For discrete onboard hubs (an > >>> example for such a hub is the Realtek RTS5411) this is often solved > >>> by supplying the hub with an 'always-on' regulator, which is kind > >>> of a hack. Some onboard hubs may require further initialization > >>> steps, like changing the state of a GPIO or enabling a clock, which > >>> requires even more hacks. This driver creates a platform device > >>> representing the hub which performs the necessary initialization. > >>> Currently it only supports switching on a single regulator, support > >>> for multiple regulators or other actions can be added as needed. > >>> Different initialization sequences can be supported based on the > >>> compatible string. > >>> > >>> Besides performing the initialization the driver can be configured > >>> to power the hub off during system suspend. This can help to extend > >>> battery life on battery powered devices which have no requirements > >>> to keep the hub powered during suspend. The driver can also be > >>> configured to leave the hub powered when a wakeup capable USB device > >>> is connected when suspending, and power it off otherwise. > >>> > >>> Changes in v15: > >>> - adjusted dependencies of USB_DWC3_CORE to make sure it can only > >>> be enabled when at least one of USB_DWC3_HOST, USB_DWC3_GADGET > >>> or USB_DWC3_DUAL_ROLE is selectable > >>> > >>> Changes in v14: > >>> - rebased on top of v5.14-rc1 > >>> - dropped DT binding patch which landed in v5.13 > >>> > >>> Changes in v13: > >>> - added patch "usb: Specify dependency on USB_XHCI_PLATFORM with > >>> 'depends on'" to the series to avoid Kconfig conflicts > >>> - added patch "arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM" > >>> to the series to keep effective defconfig unchanged > >>> > >>> Changes in v12: > >>> - onboard_hub driver: use IS_ENABLED(CONFIG_USB_ONBOARD_HUB_MODULE) > >>> in onboard_hub.h to also check for the driver built as module > >>> - onboard_hub_driver: include onboard_hub.h again to make sure there > >>> are prototype declarations for the public functions > >>> > >>> Changes in v11: > >>> - support multiple onboard hubs connected to the same parent > >>> - don't include ‘onboard_hub.h’ from the onboard hub driver > >>> > >>> Changes in v10: > >>> - always use of_is_onboard_usb_hub() stub unless ONBOARD_USB_HUB=y/m > >>> - keep 'regulator-boot-on' property for pp3300_hub > >>> > >>> Changes in v9: > >>> - added dependency on ONBOARD_USB_HUB (or !!ONBOARD_USB_HUB) to > >>> USB_PLATFORM_XHCI > >>> > >>> Changes in v7: > >>> - updated DT binding > >>> - series rebased on qcom/arm64-for-5.13 > >>> > >>> Changes in v6: > >>> - updated summary > >>> > >>> Changes in v5: > >>> - cover letter added > >>> > >>> Matthias Kaehlcke (6): > >>> usb: misc: Add onboard_usb_hub driver > >>> of/platform: Add stubs for of_platform_device_create/destroy() > >>> arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM > >>> usb: Specify dependencies on USB_XHCI_PLATFORM with 'depends on' > >>> usb: host: xhci-plat: Create platform device for onboard hubs in > >>> probe() > >>> arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub > >>> > >>> .../sysfs-bus-platform-onboard-usb-hub | 8 + > >>> MAINTAINERS | 7 + > >>> .../boot/dts/qcom/sc7180-trogdor-lazor-r0.dts | 19 +- > >>> .../boot/dts/qcom/sc7180-trogdor-lazor-r1.dts | 12 +- > >>> .../arm64/boot/dts/qcom/sc7180-trogdor-r1.dts | 19 +- > >>> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 19 +- > >>> arch/arm64/configs/defconfig | 1 + > >>> drivers/usb/cdns3/Kconfig | 2 +- > >>> drivers/usb/dwc3/Kconfig | 5 +- > >>> drivers/usb/host/Kconfig | 5 +- > > > > These Kconfig changes are causing the resulting .config to be different. > > For example, if I start with omap2plus_defconfig, the resulting .config > > before and after your series is different as shown below > > > > :/work/linux$ diff /tmp/.config .config > > 1902d1901 > > < # CONFIG_HISI_HIKEY_USB is not set > > 4992c4991 > > < CONFIG_USB_XHCI_PLATFORM=m > > --- > >> # CONFIG_USB_XHCI_PLATFORM is not set > > 5073,5075c5072 > > < # CONFIG_USB_DWC3_HOST is not set > > < # CONFIG_USB_DWC3_GADGET is not set > > < CONFIG_USB_DWC3_DUAL_ROLE=y > > --- > >> CONFIG_USB_DWC3_GADGET=y > > 5173a5171 > >> # CONFIG_USB_ONBOARD_HUB is not set > > 5285c5283 > > < CONFIG_USB_ROLE_SWITCH=m > > --- > >> # CONFIG_USB_ROLE_SWITCH is not set > > > > I would expect the same issues for multi_v7_defconfig and multi_v8_defconfig as well. > > Sorry I meant defconfig for arm64, not multi_v8_defconfig. > > I checked that for arm64 defconfig it is ok. > > > I'm ok to update the relevant defconfigs files so that the resulting .config is identical to > > before your series. Thanks! > > With the below patch you can fix it for omap2plus_defconfig and multi_v7_defconfig. > > diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig > index d9abaae118dd..8c175ab37377 100644 > --- a/arch/arm/configs/multi_v7_defconfig > +++ b/arch/arm/configs/multi_v7_defconfig > @@ -787,6 +787,7 @@ CONFIG_SND_AUDIO_GRAPH_CARD=m > CONFIG_USB=y > CONFIG_USB_OTG=y > CONFIG_USB_XHCI_HCD=y > +CONFIG_USB_XHCI_PLATFORM=y > CONFIG_USB_XHCI_MVEBU=y > CONFIG_USB_XHCI_TEGRA=m > CONFIG_USB_EHCI_HCD=y > diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig > index 2ac2418084ab..a015fb04fa25 100644 > --- a/arch/arm/configs/omap2plus_defconfig > +++ b/arch/arm/configs/omap2plus_defconfig > @@ -562,6 +562,7 @@ CONFIG_USB=m > CONFIG_USB_ANNOUNCE_NEW_DEVICES=y > CONFIG_USB_MON=m > CONFIG_USB_XHCI_HCD=m > +CONFIG_USB_XHCI_PLATFORM=m > CONFIG_USB_EHCI_HCD=m > CONFIG_USB_OHCI_HCD=m > CONFIG_USB_ACM=m Thanks for testing! I completely forgot that arm32 has all these different defconfigs. While trying to adjust qcom_defconfig I came across something that confuses me. The original defconfig results in: # CONFIG_USB_XHCI_HCD is not set CONFIG_USB_DWC3_DUAL_ROLE=y My assumption was that xHCI support is need for dwc3 dual mode (which is made explicit by https://lore.kernel.org/patchwork/patch/1468240/), is that incorrect? Maybe without xHCI support the controller can still operate in USB 2.0 dual role mode?
Hi Matthias, On 12/08/2021 20:08, Matthias Kaehlcke wrote: > Hi Roger, > > On Wed, Aug 11, 2021 at 03:56:15PM +0300, Roger Quadros wrote: >> >> >> On 11/08/2021 15:38, Roger Quadros wrote: >>> Hi Matthias, >>> >>> On 09/08/2021 18:49, Matthias Kaehlcke wrote: >>>> Hi Greg, >>>> >>>> Just wanted to check if this series is still on your radar. Is >>>> there anything that blocks it from landing (further ACKs, ...)? >>>> >>>> Thanks >>>> >>>> Matthias >>>> >>>> On Mon, Jul 26, 2021 at 05:41:12PM -0700, Matthias Kaehlcke wrote: >>>>> This series adds: >>>>> - the onboard_usb_hub_driver >>>>> - glue in the xhci-plat driver to create and destroy the >>>>> onboard_usb_hub platform devices if needed >>>>> - a device tree binding for the Realtek RTS5411 USB hub controller >>>>> - device tree changes that add RTS5411 entries for the QCA SC7180 >>>>> based boards trogdor and lazor >>>>> - a couple of stubs for platform device functions to avoid >>>>> unresolved symbols with certain kernel configs >>>>> >>>>> The main issue the driver addresses is that a USB hub needs to be >>>>> powered before it can be discovered. For discrete onboard hubs (an >>>>> example for such a hub is the Realtek RTS5411) this is often solved >>>>> by supplying the hub with an 'always-on' regulator, which is kind >>>>> of a hack. Some onboard hubs may require further initialization >>>>> steps, like changing the state of a GPIO or enabling a clock, which >>>>> requires even more hacks. This driver creates a platform device >>>>> representing the hub which performs the necessary initialization. >>>>> Currently it only supports switching on a single regulator, support >>>>> for multiple regulators or other actions can be added as needed. >>>>> Different initialization sequences can be supported based on the >>>>> compatible string. >>>>> >>>>> Besides performing the initialization the driver can be configured >>>>> to power the hub off during system suspend. This can help to extend >>>>> battery life on battery powered devices which have no requirements >>>>> to keep the hub powered during suspend. The driver can also be >>>>> configured to leave the hub powered when a wakeup capable USB device >>>>> is connected when suspending, and power it off otherwise. >>>>> >>>>> Changes in v15: >>>>> - adjusted dependencies of USB_DWC3_CORE to make sure it can only >>>>> be enabled when at least one of USB_DWC3_HOST, USB_DWC3_GADGET >>>>> or USB_DWC3_DUAL_ROLE is selectable >>>>> >>>>> Changes in v14: >>>>> - rebased on top of v5.14-rc1 >>>>> - dropped DT binding patch which landed in v5.13 >>>>> >>>>> Changes in v13: >>>>> - added patch "usb: Specify dependency on USB_XHCI_PLATFORM with >>>>> 'depends on'" to the series to avoid Kconfig conflicts >>>>> - added patch "arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM" >>>>> to the series to keep effective defconfig unchanged >>>>> >>>>> Changes in v12: >>>>> - onboard_hub driver: use IS_ENABLED(CONFIG_USB_ONBOARD_HUB_MODULE) >>>>> in onboard_hub.h to also check for the driver built as module >>>>> - onboard_hub_driver: include onboard_hub.h again to make sure there >>>>> are prototype declarations for the public functions >>>>> >>>>> Changes in v11: >>>>> - support multiple onboard hubs connected to the same parent >>>>> - don't include ‘onboard_hub.h’ from the onboard hub driver >>>>> >>>>> Changes in v10: >>>>> - always use of_is_onboard_usb_hub() stub unless ONBOARD_USB_HUB=y/m >>>>> - keep 'regulator-boot-on' property for pp3300_hub >>>>> >>>>> Changes in v9: >>>>> - added dependency on ONBOARD_USB_HUB (or !!ONBOARD_USB_HUB) to >>>>> USB_PLATFORM_XHCI >>>>> >>>>> Changes in v7: >>>>> - updated DT binding >>>>> - series rebased on qcom/arm64-for-5.13 >>>>> >>>>> Changes in v6: >>>>> - updated summary >>>>> >>>>> Changes in v5: >>>>> - cover letter added >>>>> >>>>> Matthias Kaehlcke (6): >>>>> usb: misc: Add onboard_usb_hub driver >>>>> of/platform: Add stubs for of_platform_device_create/destroy() >>>>> arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM >>>>> usb: Specify dependencies on USB_XHCI_PLATFORM with 'depends on' >>>>> usb: host: xhci-plat: Create platform device for onboard hubs in >>>>> probe() >>>>> arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub >>>>> >>>>> .../sysfs-bus-platform-onboard-usb-hub | 8 + >>>>> MAINTAINERS | 7 + >>>>> .../boot/dts/qcom/sc7180-trogdor-lazor-r0.dts | 19 +- >>>>> .../boot/dts/qcom/sc7180-trogdor-lazor-r1.dts | 12 +- >>>>> .../arm64/boot/dts/qcom/sc7180-trogdor-r1.dts | 19 +- >>>>> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 19 +- >>>>> arch/arm64/configs/defconfig | 1 + >>>>> drivers/usb/cdns3/Kconfig | 2 +- >>>>> drivers/usb/dwc3/Kconfig | 5 +- >>>>> drivers/usb/host/Kconfig | 5 +- >>> >>> These Kconfig changes are causing the resulting .config to be different. >>> For example, if I start with omap2plus_defconfig, the resulting .config >>> before and after your series is different as shown below >>> >>> :/work/linux$ diff /tmp/.config .config >>> 1902d1901 >>> < # CONFIG_HISI_HIKEY_USB is not set >>> 4992c4991 >>> < CONFIG_USB_XHCI_PLATFORM=m >>> --- >>>> # CONFIG_USB_XHCI_PLATFORM is not set >>> 5073,5075c5072 >>> < # CONFIG_USB_DWC3_HOST is not set >>> < # CONFIG_USB_DWC3_GADGET is not set >>> < CONFIG_USB_DWC3_DUAL_ROLE=y >>> --- >>>> CONFIG_USB_DWC3_GADGET=y >>> 5173a5171 >>>> # CONFIG_USB_ONBOARD_HUB is not set >>> 5285c5283 >>> < CONFIG_USB_ROLE_SWITCH=m >>> --- >>>> # CONFIG_USB_ROLE_SWITCH is not set >>> >>> I would expect the same issues for multi_v7_defconfig and multi_v8_defconfig as well. >> >> Sorry I meant defconfig for arm64, not multi_v8_defconfig. >> >> I checked that for arm64 defconfig it is ok. >> >>> I'm ok to update the relevant defconfigs files so that the resulting .config is identical to >>> before your series. Thanks! >> >> With the below patch you can fix it for omap2plus_defconfig and multi_v7_defconfig. >> >> diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig >> index d9abaae118dd..8c175ab37377 100644 >> --- a/arch/arm/configs/multi_v7_defconfig >> +++ b/arch/arm/configs/multi_v7_defconfig >> @@ -787,6 +787,7 @@ CONFIG_SND_AUDIO_GRAPH_CARD=m >> CONFIG_USB=y >> CONFIG_USB_OTG=y >> CONFIG_USB_XHCI_HCD=y >> +CONFIG_USB_XHCI_PLATFORM=y >> CONFIG_USB_XHCI_MVEBU=y >> CONFIG_USB_XHCI_TEGRA=m >> CONFIG_USB_EHCI_HCD=y >> diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig >> index 2ac2418084ab..a015fb04fa25 100644 >> --- a/arch/arm/configs/omap2plus_defconfig >> +++ b/arch/arm/configs/omap2plus_defconfig >> @@ -562,6 +562,7 @@ CONFIG_USB=m >> CONFIG_USB_ANNOUNCE_NEW_DEVICES=y >> CONFIG_USB_MON=m >> CONFIG_USB_XHCI_HCD=m >> +CONFIG_USB_XHCI_PLATFORM=m >> CONFIG_USB_EHCI_HCD=m >> CONFIG_USB_OHCI_HCD=m >> CONFIG_USB_ACM=m > > Thanks for testing! > > I completely forgot that arm32 has all these different defconfigs. > > While trying to adjust qcom_defconfig I came across something that confuses > me. The original defconfig results in: > > # CONFIG_USB_XHCI_HCD is not set > CONFIG_USB_DWC3_DUAL_ROLE=y The original Kconfig was: > config USB_DWC3_DUAL_ROLE > bool "Dual Role mode" > depends on ((USB=y || USB=USB_DWC3) && (USB_GADGET=y || USB_GADGET=USB_DWC3)) > depends on (EXTCON=y || EXTCON=USB_DWC3) Which means USB_DWC3_DUAL_ROLE can be enabled even without CONFIG_USB_XHCI_HCD. All the dual role code does is add/remove the host/gadget controller platform devices. It doesn't care whether there is a driver for it or not. i.e. there is no build dependency on CONFIG_USB_XHCI_HCD. > > My assumption was that xHCI support is need for dwc3 dual mode (which is > made explicit by https://lore.kernel.org/patchwork/patch/1468240/), is > that incorrect? Maybe without xHCI support the controller can still > operate in USB 2.0 dual role mode? > Without xHCI support the host functionality will not work at all on dwc3 dual role. So I think your Kconfig changes for USB_DWC3_DUAL_ROLE to depend on USB_XHCI_PLATFORM are correct. cheers, -roger
On Fri, Aug 13, 2021 at 09:35:53AM +0300, Roger Quadros wrote: > Hi Matthias, > > On 12/08/2021 20:08, Matthias Kaehlcke wrote: > > Hi Roger, > > > > On Wed, Aug 11, 2021 at 03:56:15PM +0300, Roger Quadros wrote: > >> > >> > >> On 11/08/2021 15:38, Roger Quadros wrote: > >>> Hi Matthias, > >>> > >>> On 09/08/2021 18:49, Matthias Kaehlcke wrote: > >>>> Hi Greg, > >>>> > >>>> Just wanted to check if this series is still on your radar. Is > >>>> there anything that blocks it from landing (further ACKs, ...)? > >>>> > >>>> Thanks > >>>> > >>>> Matthias > >>>> > >>>> On Mon, Jul 26, 2021 at 05:41:12PM -0700, Matthias Kaehlcke wrote: > >>>>> This series adds: > >>>>> - the onboard_usb_hub_driver > >>>>> - glue in the xhci-plat driver to create and destroy the > >>>>> onboard_usb_hub platform devices if needed > >>>>> - a device tree binding for the Realtek RTS5411 USB hub controller > >>>>> - device tree changes that add RTS5411 entries for the QCA SC7180 > >>>>> based boards trogdor and lazor > >>>>> - a couple of stubs for platform device functions to avoid > >>>>> unresolved symbols with certain kernel configs > >>>>> > >>>>> The main issue the driver addresses is that a USB hub needs to be > >>>>> powered before it can be discovered. For discrete onboard hubs (an > >>>>> example for such a hub is the Realtek RTS5411) this is often solved > >>>>> by supplying the hub with an 'always-on' regulator, which is kind > >>>>> of a hack. Some onboard hubs may require further initialization > >>>>> steps, like changing the state of a GPIO or enabling a clock, which > >>>>> requires even more hacks. This driver creates a platform device > >>>>> representing the hub which performs the necessary initialization. > >>>>> Currently it only supports switching on a single regulator, support > >>>>> for multiple regulators or other actions can be added as needed. > >>>>> Different initialization sequences can be supported based on the > >>>>> compatible string. > >>>>> > >>>>> Besides performing the initialization the driver can be configured > >>>>> to power the hub off during system suspend. This can help to extend > >>>>> battery life on battery powered devices which have no requirements > >>>>> to keep the hub powered during suspend. The driver can also be > >>>>> configured to leave the hub powered when a wakeup capable USB device > >>>>> is connected when suspending, and power it off otherwise. > >>>>> > >>>>> Changes in v15: > >>>>> - adjusted dependencies of USB_DWC3_CORE to make sure it can only > >>>>> be enabled when at least one of USB_DWC3_HOST, USB_DWC3_GADGET > >>>>> or USB_DWC3_DUAL_ROLE is selectable > >>>>> > >>>>> Changes in v14: > >>>>> - rebased on top of v5.14-rc1 > >>>>> - dropped DT binding patch which landed in v5.13 > >>>>> > >>>>> Changes in v13: > >>>>> - added patch "usb: Specify dependency on USB_XHCI_PLATFORM with > >>>>> 'depends on'" to the series to avoid Kconfig conflicts > >>>>> - added patch "arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM" > >>>>> to the series to keep effective defconfig unchanged > >>>>> > >>>>> Changes in v12: > >>>>> - onboard_hub driver: use IS_ENABLED(CONFIG_USB_ONBOARD_HUB_MODULE) > >>>>> in onboard_hub.h to also check for the driver built as module > >>>>> - onboard_hub_driver: include onboard_hub.h again to make sure there > >>>>> are prototype declarations for the public functions > >>>>> > >>>>> Changes in v11: > >>>>> - support multiple onboard hubs connected to the same parent > >>>>> - don't include ‘onboard_hub.h’ from the onboard hub driver > >>>>> > >>>>> Changes in v10: > >>>>> - always use of_is_onboard_usb_hub() stub unless ONBOARD_USB_HUB=y/m > >>>>> - keep 'regulator-boot-on' property for pp3300_hub > >>>>> > >>>>> Changes in v9: > >>>>> - added dependency on ONBOARD_USB_HUB (or !!ONBOARD_USB_HUB) to > >>>>> USB_PLATFORM_XHCI > >>>>> > >>>>> Changes in v7: > >>>>> - updated DT binding > >>>>> - series rebased on qcom/arm64-for-5.13 > >>>>> > >>>>> Changes in v6: > >>>>> - updated summary > >>>>> > >>>>> Changes in v5: > >>>>> - cover letter added > >>>>> > >>>>> Matthias Kaehlcke (6): > >>>>> usb: misc: Add onboard_usb_hub driver > >>>>> of/platform: Add stubs for of_platform_device_create/destroy() > >>>>> arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM > >>>>> usb: Specify dependencies on USB_XHCI_PLATFORM with 'depends on' > >>>>> usb: host: xhci-plat: Create platform device for onboard hubs in > >>>>> probe() > >>>>> arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub > >>>>> > >>>>> .../sysfs-bus-platform-onboard-usb-hub | 8 + > >>>>> MAINTAINERS | 7 + > >>>>> .../boot/dts/qcom/sc7180-trogdor-lazor-r0.dts | 19 +- > >>>>> .../boot/dts/qcom/sc7180-trogdor-lazor-r1.dts | 12 +- > >>>>> .../arm64/boot/dts/qcom/sc7180-trogdor-r1.dts | 19 +- > >>>>> arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 19 +- > >>>>> arch/arm64/configs/defconfig | 1 + > >>>>> drivers/usb/cdns3/Kconfig | 2 +- > >>>>> drivers/usb/dwc3/Kconfig | 5 +- > >>>>> drivers/usb/host/Kconfig | 5 +- > >>> > >>> These Kconfig changes are causing the resulting .config to be different. > >>> For example, if I start with omap2plus_defconfig, the resulting .config > >>> before and after your series is different as shown below > >>> > >>> :/work/linux$ diff /tmp/.config .config > >>> 1902d1901 > >>> < # CONFIG_HISI_HIKEY_USB is not set > >>> 4992c4991 > >>> < CONFIG_USB_XHCI_PLATFORM=m > >>> --- > >>>> # CONFIG_USB_XHCI_PLATFORM is not set > >>> 5073,5075c5072 > >>> < # CONFIG_USB_DWC3_HOST is not set > >>> < # CONFIG_USB_DWC3_GADGET is not set > >>> < CONFIG_USB_DWC3_DUAL_ROLE=y > >>> --- > >>>> CONFIG_USB_DWC3_GADGET=y > >>> 5173a5171 > >>>> # CONFIG_USB_ONBOARD_HUB is not set > >>> 5285c5283 > >>> < CONFIG_USB_ROLE_SWITCH=m > >>> --- > >>>> # CONFIG_USB_ROLE_SWITCH is not set > >>> > >>> I would expect the same issues for multi_v7_defconfig and multi_v8_defconfig as well. > >> > >> Sorry I meant defconfig for arm64, not multi_v8_defconfig. > >> > >> I checked that for arm64 defconfig it is ok. > >> > >>> I'm ok to update the relevant defconfigs files so that the resulting .config is identical to > >>> before your series. Thanks! > >> > >> With the below patch you can fix it for omap2plus_defconfig and multi_v7_defconfig. > >> > >> diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig > >> index d9abaae118dd..8c175ab37377 100644 > >> --- a/arch/arm/configs/multi_v7_defconfig > >> +++ b/arch/arm/configs/multi_v7_defconfig > >> @@ -787,6 +787,7 @@ CONFIG_SND_AUDIO_GRAPH_CARD=m > >> CONFIG_USB=y > >> CONFIG_USB_OTG=y > >> CONFIG_USB_XHCI_HCD=y > >> +CONFIG_USB_XHCI_PLATFORM=y > >> CONFIG_USB_XHCI_MVEBU=y > >> CONFIG_USB_XHCI_TEGRA=m > >> CONFIG_USB_EHCI_HCD=y > >> diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig > >> index 2ac2418084ab..a015fb04fa25 100644 > >> --- a/arch/arm/configs/omap2plus_defconfig > >> +++ b/arch/arm/configs/omap2plus_defconfig > >> @@ -562,6 +562,7 @@ CONFIG_USB=m > >> CONFIG_USB_ANNOUNCE_NEW_DEVICES=y > >> CONFIG_USB_MON=m > >> CONFIG_USB_XHCI_HCD=m > >> +CONFIG_USB_XHCI_PLATFORM=m > >> CONFIG_USB_EHCI_HCD=m > >> CONFIG_USB_OHCI_HCD=m > >> CONFIG_USB_ACM=m > > > > Thanks for testing! > > > > I completely forgot that arm32 has all these different defconfigs. > > > > While trying to adjust qcom_defconfig I came across something that confuses > > me. The original defconfig results in: > > > > # CONFIG_USB_XHCI_HCD is not set > > CONFIG_USB_DWC3_DUAL_ROLE=y > > The original Kconfig was: > > > config USB_DWC3_DUAL_ROLE > > bool "Dual Role mode" > > depends on ((USB=y || USB=USB_DWC3) && (USB_GADGET=y || USB_GADGET=USB_DWC3)) > > depends on (EXTCON=y || EXTCON=USB_DWC3) > > Which means USB_DWC3_DUAL_ROLE can be enabled even without CONFIG_USB_XHCI_HCD. > > All the dual role code does is add/remove the host/gadget controller platform devices. > It doesn't care whether there is a driver for it or not. > i.e. there is no build dependency on CONFIG_USB_XHCI_HCD. > > > > > My assumption was that xHCI support is need for dwc3 dual mode (which is > > made explicit by https://lore.kernel.org/patchwork/patch/1468240/), is > > that incorrect? Maybe without xHCI support the controller can still > > operate in USB 2.0 dual role mode? > > > > Without xHCI support the host functionality will not work at all on dwc3 dual role. > So I think your Kconfig changes for USB_DWC3_DUAL_ROLE to depend on USB_XHCI_PLATFORM > are correct. Thanks for the clarification!
This series adds: - the onboard_usb_hub_driver - glue in the xhci-plat driver to create and destroy the onboard_usb_hub platform devices if needed - a device tree binding for the Realtek RTS5411 USB hub controller - device tree changes that add RTS5411 entries for the QCA SC7180 based boards trogdor and lazor - a couple of stubs for platform device functions to avoid unresolved symbols with certain kernel configs The main issue the driver addresses is that a USB hub needs to be powered before it can be discovered. For discrete onboard hubs (an example for such a hub is the Realtek RTS5411) this is often solved by supplying the hub with an 'always-on' regulator, which is kind of a hack. Some onboard hubs may require further initialization steps, like changing the state of a GPIO or enabling a clock, which requires even more hacks. This driver creates a platform device representing the hub which performs the necessary initialization. Currently it only supports switching on a single regulator, support for multiple regulators or other actions can be added as needed. Different initialization sequences can be supported based on the compatible string. Besides performing the initialization the driver can be configured to power the hub off during system suspend. This can help to extend battery life on battery powered devices which have no requirements to keep the hub powered during suspend. The driver can also be configured to leave the hub powered when a wakeup capable USB device is connected when suspending, and power it off otherwise. Changes in v15: - adjusted dependencies of USB_DWC3_CORE to make sure it can only be enabled when at least one of USB_DWC3_HOST, USB_DWC3_GADGET or USB_DWC3_DUAL_ROLE is selectable Changes in v14: - rebased on top of v5.14-rc1 - dropped DT binding patch which landed in v5.13 Changes in v13: - added patch "usb: Specify dependency on USB_XHCI_PLATFORM with 'depends on'" to the series to avoid Kconfig conflicts - added patch "arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM" to the series to keep effective defconfig unchanged Changes in v12: - onboard_hub driver: use IS_ENABLED(CONFIG_USB_ONBOARD_HUB_MODULE) in onboard_hub.h to also check for the driver built as module - onboard_hub_driver: include onboard_hub.h again to make sure there are prototype declarations for the public functions Changes in v11: - support multiple onboard hubs connected to the same parent - don't include ‘onboard_hub.h’ from the onboard hub driver Changes in v10: - always use of_is_onboard_usb_hub() stub unless ONBOARD_USB_HUB=y/m - keep 'regulator-boot-on' property for pp3300_hub Changes in v9: - added dependency on ONBOARD_USB_HUB (or !!ONBOARD_USB_HUB) to USB_PLATFORM_XHCI Changes in v7: - updated DT binding - series rebased on qcom/arm64-for-5.13 Changes in v6: - updated summary Changes in v5: - cover letter added Matthias Kaehlcke (6): usb: misc: Add onboard_usb_hub driver of/platform: Add stubs for of_platform_device_create/destroy() arm64: defconfig: Explicitly enable USB_XHCI_PLATFORM usb: Specify dependencies on USB_XHCI_PLATFORM with 'depends on' usb: host: xhci-plat: Create platform device for onboard hubs in probe() arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub .../sysfs-bus-platform-onboard-usb-hub | 8 + MAINTAINERS | 7 + .../boot/dts/qcom/sc7180-trogdor-lazor-r0.dts | 19 +- .../boot/dts/qcom/sc7180-trogdor-lazor-r1.dts | 12 +- .../arm64/boot/dts/qcom/sc7180-trogdor-r1.dts | 19 +- arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 19 +- arch/arm64/configs/defconfig | 1 + drivers/usb/cdns3/Kconfig | 2 +- drivers/usb/dwc3/Kconfig | 5 +- drivers/usb/host/Kconfig | 5 +- drivers/usb/host/xhci-plat.c | 6 + drivers/usb/host/xhci.h | 2 + drivers/usb/misc/Kconfig | 17 + drivers/usb/misc/Makefile | 1 + drivers/usb/misc/onboard_usb_hub.c | 497 ++++++++++++++++++ include/linux/of_platform.h | 22 +- include/linux/usb/onboard_hub.h | 18 + 17 files changed, 621 insertions(+), 39 deletions(-) create mode 100644 Documentation/ABI/testing/sysfs-bus-platform-onboard-usb-hub create mode 100644 drivers/usb/misc/onboard_usb_hub.c create mode 100644 include/linux/usb/onboard_hub.h