diff mbox series

[2/6] mmc: sdhci-eadhc-imx: select the correct mode for auto tuning

Message ID 1629117508-4886-2-git-send-email-haibo.chen@nxp.com
State Superseded
Headers show
Series [1/6] mmc: sdhci-esdhc-imx: remove redundant code for manual tuning | expand

Commit Message

Bough Chen Aug. 16, 2021, 12:38 p.m. UTC 
From: Haibo Chen <haibo.chen@nxp.com>

USDHC hardware auto tuning circuit support check 1/4/8 data lines
and cmd line. Out of reset uSDHC, it default select check 4 data
lines and do not check cmd line. This is incorrect if we use 8 data
lines. So need to config the auto tuning mode according to current
bus width.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
---
 drivers/mmc/host/sdhci-esdhc-imx.c | 33 ++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)
diff mbox series

Patch

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index a49fac719fca..f18d169bc8ff 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -94,6 +94,11 @@ 
 
 #define ESDHC_VEND_SPEC2		0xc8
 #define ESDHC_VEND_SPEC2_EN_BUSY_IRQ	(1 << 8)
+#define ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN	(1 << 4)
+#define ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN	(0 << 4)
+#define ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN	(2 << 4)
+#define ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN	(1 << 6)
+#define ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK	(7 << 4)
 
 #define ESDHC_TUNING_CTRL		0xcc
 #define ESDHC_STD_TUNING_EN		(1 << 24)
@@ -114,6 +119,7 @@ 
 #define ESDHC_CTRL_4BITBUS		(0x1 << 1)
 #define ESDHC_CTRL_8BITBUS		(0x2 << 1)
 #define ESDHC_CTRL_BUSWIDTH_MASK	(0x3 << 1)
+#define USDHC_GET_BUSWIDTH(c) (c & ESDHC_CTRL_BUSWIDTH_MASK)
 
 /*
  * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC:
@@ -407,6 +413,30 @@  static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host)
 		dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__);
 }
 
+/* Enable the auto tuning circuit to check the CMD line and BUS line */
+static inline void usdhc_auto_tuning_mode_sel(struct sdhci_host *host)
+{
+	u32 buswidth, auto_tune_buswidth;
+
+	buswidth = USDHC_GET_BUSWIDTH(readl(host->ioaddr + SDHCI_HOST_CONTROL));
+
+	switch (buswidth) {
+	case ESDHC_CTRL_8BITBUS:
+		auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN;
+		break;
+	case ESDHC_CTRL_4BITBUS:
+		auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN;
+		break;
+	default:	/* 1BITBUS */
+		auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN;
+		break;
+	}
+
+	esdhc_clrset_le(host, ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK,
+			auto_tune_buswidth | ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN,
+			ESDHC_VEND_SPEC2);
+}
+
 static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
 {
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
@@ -643,6 +673,7 @@  static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 				v |= ESDHC_MIX_CTRL_EXE_TUNE;
 				m |= ESDHC_MIX_CTRL_FBCLK_SEL;
 				m |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;
+				usdhc_auto_tuning_mode_sel(host);
 			} else {
 				v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
 			}
@@ -1012,6 +1043,8 @@  static void esdhc_post_tuning(struct sdhci_host *host)
 {
 	u32 reg;
 
+	usdhc_auto_tuning_mode_sel(host);
+
 	reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
 	reg &= ~ESDHC_MIX_CTRL_EXE_TUNE;
 	reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN;