| Message ID | 20200629114927.17379-1-bruno.thomsen@gmail.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [1/3] dt-bindings: ARM: imx: add kamstrup flex concentrator to schema | expand |
On Mon, Jun 29, 2020 at 01:49:25PM +0200, Bruno Thomsen wrote: > Add Kamstrup flex concentrator compatibles to the schema so we can > make use of them for the validation. > > Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> 'dt-bindings: fsl: ...' should be just fine as subject prefix. Shawn > --- > Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++ > 1 file changed, 2 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml > index 05906e291e38..66627b272e40 100644 > --- a/Documentation/devicetree/bindings/arm/fsl.yaml > +++ b/Documentation/devicetree/bindings/arm/fsl.yaml > @@ -299,6 +299,8 @@ properties: > - enum: > - fsl,imx7d-sdb # i.MX7 SabreSD Board > - fsl,imx7d-sdb-reva # i.MX7 SabreSD Rev-A Board > + - kam,imx7d-flex-concentrator # Kamstrup OMNIA Flex Concentrator > + - kam,imx7d-flex-concentrator-mfg # Kamstrup OMNIA Flex Concentrator in manufacturing mode > - novtech,imx7d-meerkat96 # i.MX7 Meerkat96 Board > - technexion,imx7d-pico-dwarf # TechNexion i.MX7D Pico-Dwarf > - technexion,imx7d-pico-hobbit # TechNexion i.MX7D Pico-Hobbit > > base-commit: 9ebcfadb0610322ac537dd7aa5d9cbc2b2894c68 > -- > 2.26.2 >
On Mon, Jun 29, 2020 at 01:49:26PM +0200, Bruno Thomsen wrote: > This adds support for the OMNIA Flex Concentrator product > from Kamstrup A/S. It's providing radio mesh communication > infrastructure for smart electricity meters. > > Kamstrup OMNIA is a modular and scalable smart grid platform. > > Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> > --- > arch/arm/boot/dts/Makefile | 2 + > .../boot/dts/imx7d-flex-concentrator-mfg.dts | 25 ++ > arch/arm/boot/dts/imx7d-flex-concentrator.dts | 307 ++++++++++++++++++ > 3 files changed, 334 insertions(+) > create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts > create mode 100644 arch/arm/boot/dts/imx7d-flex-concentrator.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index e6a1cac0bfc7..bf5c5d86a2e8 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -628,6 +628,8 @@ dtb-$(CONFIG_SOC_IMX7D) += \ > imx7d-colibri-emmc-aster.dtb \ > imx7d-colibri-emmc-eval-v3.dtb \ > imx7d-colibri-eval-v3.dtb \ > + imx7d-flex-concentrator.dtb \ > + imx7d-flex-concentrator-mfg.dtb \ > imx7d-mba7.dtb \ > imx7d-meerkat96.dtb \ > imx7d-nitrogen7.dtb \ > diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts > new file mode 100644 > index 000000000000..789f0837058f > --- /dev/null > +++ b/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts > @@ -0,0 +1,25 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Device Tree Source for Kamstrup OMNIA Flex Concentrator in > + * manufacturing/debugging mode. > + * > + * Copyright (C) 2020 Kamstrup A/S > + * Author: Bruno Thomsen <bruno.thomsen@gmail.com> > + */ > + > +/dts-v1/; > + > +#include "imx7d-flex-concentrator.dts" > + > +/ { > + model = "Kamstrup OMNIA Flex Concentrator - Manufacturing"; > + compatible = "kam,imx7d-flex-concentrator-mfg", "kam,imx7d-flex-concentrator", "fsl,imx7d"; > + > + chosen { > + stdout-path = &uart4; > + }; > +}; > + > +&uart4 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator.dts b/arch/arm/boot/dts/imx7d-flex-concentrator.dts > new file mode 100644 > index 000000000000..887135cca650 > --- /dev/null > +++ b/arch/arm/boot/dts/imx7d-flex-concentrator.dts > @@ -0,0 +1,307 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Device Tree Source for Kamstrup OMNIA Flex Concentrator. > + * > + * Copyright (C) 2020 Kamstrup A/S > + * Author: Bruno Thomsen <bruno.thomsen@gmail.com> > + */ > + > +/dts-v1/; > + > +#include "imx7d-tqma7.dtsi" > + > +/* Some I2C devices on TQMa7 SoM are not mounted */ > +/delete-node/ &m24c64; > +/delete-node/ &ds1339; > + > +/ { > + model = "Kamstrup OMNIA Flex Concentrator"; > + compatible = "kam,imx7d-flex-concentrator", "fsl,imx7d"; > + > + memory@80000000 { > + device_type = "memory"; > + /* 1024 MB - TQMa7D board configuration */ > + reg = <0x80000000 0x40000000>; > + }; > + > + reg_usb_otg2_vbus: regulator-usb-otg2-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "VBUS_USBOTG2"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_vref_1v8: regulator-vref-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "VCC1V8_REF"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + vin-supply = <&sw2_reg>; > + }; > + > + /* > + * Human Machine Interface consists of 4 dual red/green LEDs. > + * hmi-a-green is controlled directly by the switch-mode power supply. > + * hmi-a-red is not used. > + */ > + gpio-leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_leds>; > + > + hmi-b-red { > + label = "hmi-b:red:provisioning"; > + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-b-green { > + label = "hmi-b:green:operation"; > + gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-c-red { > + label = "hmi-c:red:mesh-error"; > + gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-c-green { > + label = "hmi-c:green:mesh-activity"; > + gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-d-red { > + label = "hmi-d:red:wan-down"; > + gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + > + hmi-d-green { > + label = "hmi-d:green:ipsec-up"; > + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + }; > + > + /* > + * Errata e10574 board restart workaround. > + */ > + gpio-restart { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_restart>; > + compatible = "gpio-restart"; > + gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; > + priority = <200>; > + }; > +}; > + > +/* > + * External watchdog feature provided by pcf2127. > + */ > +&wdog1 { Please keep these labeling nodes sort alphabetically. > + status = "disabled"; > +}; > + > +/* > + * Detection signals for internal USB modules. > + * Used for robust USB plug and play handling such as USB downstream port > + * power-cycle and USB hub reset in case of misbehaving or crashed modules. > + * > + * SMPS - AC input monitor based on zero crossing. > + * Used for last gasp notification. > + */ > +&gpio3 { > + gpio-line-names = "", "", "", "", "", "", "", "", > + "", "", "", "", "smps-ac-monitor", "", "usb-hub-reset", "", > + "", "", "", "", "", "", "", "", > + "", "module-b-detection", "", "module-a-detection", "", "", "", ""; > +}; > + > +/* > + * Tamper IRQ trigger timestamp reading. > + * Used for sealed cover opened notification. > + */ > +&gpio5 { > + gpio-line-names = "", "", "", "", "", "", "", "", > + "", "", "", "", "rtc-tamper-irq", "", "", "", > + "", "", "", "", "", "", "", "", > + "", "", "", "", "", "", "", ""; > +}; > + > +/* > + * Analog signals > + * ADC1_IN0: SMPS - 5V output monitor (voltage divider: 1/0.2806) > + */ > +&adc1 { > + vref-supply = <®_vref_1v8>; > + status = "okay"; > +}; > + > +&ecspi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi2>; > + num-chipselects = <1>; > + cs-gpios = <&gpio4 23 GPIO_ACTIVE_LOW>; > + status = "okay"; > + > + pcf2127: rtc@0 { > + compatible = "nxp,pcf2127"; > + reg = <0>; > + spi-max-frequency = <2000000>; > + }; > +}; > + > +&ecspi4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ecspi4>; > + num-chipselects = <1>; > + cs-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>; > + status = "okay"; > + > + /* > + * ST chip maximum SPI clock frequency is 33 MHz. > + * > + * TCG specification - Section 6.4.1 Clocking: > + * TPM shall support a SPI clock frequency range of 10-24 MHz. > + */ > + st33htph: tpm-tis@0 { > + compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi"; > + reg = <0>; > + spi-max-frequency = <24000000>; > + }; > +}; > + > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet1>; > + phy-mode = "rmii"; > + phy-reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>; > + phy-reset-duration = <100>; > + phy-reset-post-delay = <1000>; These properties are deprecated. > + phy-handle = <ðphy>; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + ethphy: ethernet-phy@1 { > + /* Micrel KSZ8051RNLV */ > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > + }; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_misc>; > + > + pinctrl_ecspi2: ecspi2grp { > + fsl,pins = < > + MX7D_PAD_ECSPI2_MISO__ECSPI2_MISO 0x7c /* X2-15 */ > + MX7D_PAD_ECSPI2_MOSI__ECSPI2_MOSI 0x74 /* X2-18 */ > + MX7D_PAD_ECSPI2_SCLK__ECSPI2_SCLK 0x74 /* X2-13 */ > + MX7D_PAD_ECSPI2_SS0__GPIO4_IO23 0x74 /* X2-20 */ > + /* RTC - Tamper IRQ */ > + MX7D_PAD_SD2_CLK__GPIO5_IO12 0x3c /* X1-92 */ > + >; > + }; > + > + pinctrl_ecspi4: ecspi4grp { > + fsl,pins = < > + MX7D_PAD_LCD_CLK__ECSPI4_MISO 0x7c /* X2-72 */ > + MX7D_PAD_LCD_ENABLE__ECSPI4_MOSI 0x74 /* X2-68 */ > + MX7D_PAD_LCD_HSYNC__ECSPI4_SCLK 0x74 /* X2-76 */ > + MX7D_PAD_LCD_VSYNC__GPIO3_IO3 0x74 /* X2-78 */ > + >; > + }; > + > + pinctrl_leds: ledsgrp { > + fsl,pins = < > + MX7D_PAD_LCD_DATA01__GPIO3_IO6 0x14 /* X2-82 */ > + MX7D_PAD_EPDC_BDR0__GPIO2_IO28 0x14 /* X1-82 */ > + MX7D_PAD_EPDC_BDR1__GPIO2_IO29 0x14 /* X1-84 */ > + MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 0x14 /* X1-86 */ > + MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 0x14 /* X1-88 */ > + MX7D_PAD_UART2_TX_DATA__GPIO4_IO3 0x14 /* X1-90 */ > + >; > + }; > + > + pinctrl_enet1: enet1grp { Please keep these pinctrl entries sort alphabetically. Shawn > + fsl,pins = < > + MX7D_PAD_GPIO1_IO10__ENET1_MDIO 0x03 /* X2-48 */ > + MX7D_PAD_GPIO1_IO11__ENET1_MDC 0x03 /* X2-46 */ > + MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 0x71 /* X2-53 */ > + MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 0x71 /* X2-55 */ > + MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x71 /* X2-61 */ > + MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 0x79 /* X2-56 */ > + MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 0x79 /* X2-58 */ > + MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x79 /* X2-64 */ > + MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER 0x73 /* X2-52 */ > + /* PHY reset: SION, 100kPU, SRE_FAST, DSE_X1 */ > + MX7D_PAD_ENET1_COL__GPIO7_IO15 0x40000070 /* X1-96 */ > + /* Clock from PHY to MAC */ > + MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1 0x40000073 /* X3-4 */ > + >; > + }; > + > + pinctrl_misc: miscgrp { > + fsl,pins = < > + /* Module A detection (low = present) */ > + MX7D_PAD_LCD_DATA22__GPIO3_IO27 0x7c /* X2-105 */ > + /* Module B detection (low = present) */ > + MX7D_PAD_LCD_DATA20__GPIO3_IO25 0x7c /* X2-103 */ > + /* SMPS - AC input monitor (high = failure) */ > + MX7D_PAD_LCD_DATA07__GPIO3_IO12 0x7c /* X2-88 */ > + /* USB - Hub reset */ > + MX7D_PAD_LCD_DATA09__GPIO3_IO14 0x74 /* X2-92 */ > + >; > + }; > + > + pinctrl_uart4: uart4grp { > + fsl,pins = < > + MX7D_PAD_SAI2_TX_SYNC__UART4_DCE_RX 0x7e /* X3-14 */ > + MX7D_PAD_SAI2_TX_BCLK__UART4_DCE_TX 0x76 /* X3-16 */ > + >; > + }; > + > + pinctrl_restart: restartgrp { > + fsl,pins = < > + MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12 0x74 /* X1-94 */ > + >; > + }; > +}; > + > +&iomuxc_lpsr { > + pinctrl_usbotg2: usbotg2grp { > + fsl,pins = < > + MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC 0x5c /* X3-11 */ > + MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x59 /* X3-9 */ > + >; > + }; > + > +}; > + > +&usbotg2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg2>; > + vbus-supply = <®_usb_otg2_vbus>; > + srp-disable; > + hnp-disable; > + adp-disable; > + dr_mode = "host"; > + status = "okay"; > +}; > + > +&uart4 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart4>; > + assigned-clocks = <&clks IMX7D_UART4_ROOT_SRC>; > + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>; > +}; > -- > 2.26.2 >
Den man. 13. jul. 2020 kl. 04.52 skrev Shawn Guo <shawnguo@kernel.org>: > > On Mon, Jun 29, 2020 at 01:49:26PM +0200, Bruno Thomsen wrote: > > +&fec1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_enet1>; > > + phy-mode = "rmii"; > > + phy-reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>; > > + phy-reset-duration = <100>; > > + phy-reset-post-delay = <1000>; > > These properties are deprecated. Thanks for review Shawn. I have not yet been successful in converting the deprecated properties to generic phy properties, so hoping I could get a hit. Kernel error messages: mdio_bus 30be0000.ethernet-1: MDIO device at address 1 is missing. fec 30be0000.ethernet eth0: Unable to connect to phy Updated device tree section: &fec1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet1>; phy-mode = "rmii"; phy-handle = <ðphy>; status = "okay"; mdio { #address-cells = <1>; #size-cells = <0>; ethphy: ethernet-phy@1 { /* Micrel KSZ8051RNLV */ compatible = "ethernet-phy-ieee802.3-c22"; reg = <1>; max-speed = <100>; reset-assert-us = <100000>; reset-deassert-us = <1000000>; reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>; }; }; }; /Bruno > > + phy-handle = <ðphy>; > > + status = "okay"; > > + > > + mdio { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + ethphy: ethernet-phy@1 { > > + /* Micrel KSZ8051RNLV */ > > + compatible = "ethernet-phy-ieee802.3-c22"; > > + reg = <1>; > > + }; > > + }; > > +};
Hi Bruno, On Tue, Jul 14, 2020 at 7:03 AM Bruno Thomsen <bruno.thomsen@gmail.com> wrote: > I have not yet been successful in converting the deprecated properties > to generic phy properties, so hoping I could get a hit. > > Kernel error messages: > mdio_bus 30be0000.ethernet-1: MDIO device at address 1 is missing. Please double-check whether 1 is the correct address for the KSZ8051 Ethernet PHY as per your schematics. Are there external pull-up/pull-down resistors for strapping the various configuration pins for the PHY? Or are the pull-up/pull-down provided by the i.MX7D pins? If there are no external pull-ups, please make sure to configure the pinctrl_enet1 accordingly, so that the Ethernet PHY address can be properly configured and then mdio_bus driver can find it at the correct address. Please check in arch/arm/boot/dts/imx6qdl-sr-som.dtsi for an example on how to configure the Ethernet PHY pin strapping via iMX IOMUX.
Den tir. 14. jul. 2020 kl. 13.54 skrev Fabio Estevam <festevam@gmail.com>: > > Hi Bruno, > > On Tue, Jul 14, 2020 at 7:03 AM Bruno Thomsen <bruno.thomsen@gmail.com> wrote: > > > I have not yet been successful in converting the deprecated properties > > to generic phy properties, so hoping I could get a hit. > > > > Kernel error messages: > > mdio_bus 30be0000.ethernet-1: MDIO device at address 1 is missing. > > Please double-check whether 1 is the correct address for the KSZ8051 > Ethernet PHY as per your schematics. Hi Fabio, Thanks for the hints. Yes, the address is correct and configured with external resistors, but just realised that I wrote the wrong device name in the comment, it's actually KSZ8081RNB. Ethernet has been working with multiple mainline kernel versions (latest being 5.7.8) for the last year or so when using the DTS in patch. So I am pretty sure hardware and setup of mux is correct'ish. Kernel trace from patch version: kernel: Micrel KSZ8081 or KSZ8091 30be0000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL) Error first occurs when switching from fec phy reset to mdio phy reset code path, I understand that the fec phy reset is obsolete as phy properties was wrongly added to the mac and of course should be part of the phy (separate chip). When debugging it I end up with the get_phy_device() call not working inside of_mdiobus_register_phy(). Workaround at the moment seems to be extending compatible with "ethernet-phy-id0022.1560" to disable auto detection of phy type, and then Ethernet works again. At least the same PHY driver trace can be found and full transmission speed can be used without packet errors/loss. > Are there external pull-up/pull-down resistors for strapping the > various configuration pins for the PHY? Or are the pull-up/pull-down > provided by the i.MX7D pins? Config strapping is done with external resistors. > If there are no external pull-ups, please make sure to configure the > pinctrl_enet1 accordingly, so that the Ethernet PHY address can be > properly configured and then mdio_bus driver can find it at the > correct address. > > Please check in arch/arm/boot/dts/imx6qdl-sr-som.dtsi for an example > on how to configure the Ethernet PHY pin strapping via iMX IOMUX. Thanks, good examples can be hard to find. /Bruno
On Mon, 29 Jun 2020 13:49:25 +0200, Bruno Thomsen wrote: > Add Kamstrup flex concentrator compatibles to the schema so we can > make use of them for the validation. > > Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> > --- > Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++ > 1 file changed, 2 insertions(+) > Acked-by: Rob Herring <robh@kernel.org>
Hi Bruno, On Wed, Jul 15, 2020 at 11:22 AM Bruno Thomsen <bruno.thomsen@gmail.com> wrote: > Thanks for the hints. > > Yes, the address is correct and configured with external resistors, > but just realised that I wrote the wrong device name in the comment, > it's actually KSZ8081RNB. > > Ethernet has been working with multiple mainline kernel versions > (latest being 5.7.8) > for the last year or so when using the DTS in patch. So I am pretty sure > hardware and setup of mux is correct'ish. > > Kernel trace from patch version: > kernel: Micrel KSZ8081 or KSZ8091 30be0000.ethernet-1:01: attached PHY driver > [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL) > > Error first occurs when switching from fec phy reset to mdio phy reset > code path, > I understand that the fec phy reset is obsolete as phy properties was wrongly > added to the mac and of course should be part of the phy (separate chip). > > When debugging it I end up with the get_phy_device() call not working > inside of_mdiobus_register_phy(). It would be nice if you could report this to the Ethernet PHY folks at netdev@vger.kernel.org
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 05906e291e38..66627b272e40 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -299,6 +299,8 @@ properties: - enum: - fsl,imx7d-sdb # i.MX7 SabreSD Board - fsl,imx7d-sdb-reva # i.MX7 SabreSD Rev-A Board + - kam,imx7d-flex-concentrator # Kamstrup OMNIA Flex Concentrator + - kam,imx7d-flex-concentrator-mfg # Kamstrup OMNIA Flex Concentrator in manufacturing mode - novtech,imx7d-meerkat96 # i.MX7 Meerkat96 Board - technexion,imx7d-pico-dwarf # TechNexion i.MX7D Pico-Dwarf - technexion,imx7d-pico-hobbit # TechNexion i.MX7D Pico-Hobbit
Add Kamstrup flex concentrator compatibles to the schema so we can make use of them for the validation. Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> --- Documentation/devicetree/bindings/arm/fsl.yaml | 2 ++ 1 file changed, 2 insertions(+) base-commit: 9ebcfadb0610322ac537dd7aa5d9cbc2b2894c68