diff mbox series

[v3,2/4] gpio: visconti: Add Toshiba Visconti GPIO support

Message ID 20201201181406.2371881-3-nobuhiro1.iwamatsu@toshiba.co.jp
State Superseded
Headers show
Series gpio: visconti: Add Toshiba Visconti GPIO support | expand

Commit Message

Nobuhiro Iwamatsu Dec. 1, 2020, 6:14 p.m. UTC
Add the GPIO driver for Toshiba Visconti ARM SoCs.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
---
 drivers/gpio/Kconfig                      |   9 +
 drivers/gpio/Makefile                     |   1 +
 drivers/gpio/gpio-visconti.c              | 232 ++++++++++++++++++++++
 drivers/pinctrl/visconti/pinctrl-common.c |  23 +++
 4 files changed, 265 insertions(+)
 create mode 100644 drivers/gpio/gpio-visconti.c

Comments

Punit Agrawal Dec. 3, 2020, 10:03 a.m. UTC | #1
Hi Iwamatsu-san,

A couple of very minor comments below -

Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> writes:

> Add the GPIO driver for Toshiba Visconti ARM SoCs.

>

> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>

> ---

>  drivers/gpio/Kconfig                      |   9 +

>  drivers/gpio/Makefile                     |   1 +

>  drivers/gpio/gpio-visconti.c              | 232 ++++++++++++++++++++++

>  drivers/pinctrl/visconti/pinctrl-common.c |  23 +++

>  4 files changed, 265 insertions(+)

>  create mode 100644 drivers/gpio/gpio-visconti.c

>


[...]

> diff --git a/drivers/gpio/gpio-visconti.c b/drivers/gpio/gpio-visconti.c

> new file mode 100644

> index 000000000000..17e6da161f48

> --- /dev/null

> +++ b/drivers/gpio/gpio-visconti.c

> @@ -0,0 +1,232 @@

> +// SPDX-License-Identifier: GPL-2.0

> +/*

> + * Toshiba Visconti GPIO Support

> + *

> + * (C) Copyright 2020 Toshiba Electronic Devices & Storage Corporation

> + * (C) Copyright 2020 Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>

> + */

> +

> +#include <linux/init.h>

> +#include <linux/interrupt.h>

> +#include <linux/module.h>

> +#include <linux/io.h>

> +#include <linux/platform_device.h>

> +#include <linux/gpio/driver.h>

> +#include <linux/of.h>

> +#include <linux/bitops.h>

> +

> +/* register offset */

> +#define GPIO_DIR	0x00

> +#define GPIO_IDATA	0x08

> +#define GPIO_ODATA	0x10

> +#define GPIO_OSET	0x18

> +#define GPIO_OCLR	0x20

> +#define GPIO_INTMODE	0x30

> +

> +#define VISCONTI_GPIO_NR	32


The macro doesn't seem to be used. Can we drop this? On the other hand
should there be a macro to indicate the maximum number of GPIO lines
that support interrupt (16)?

> +

> +struct visconti_gpio {

> +	void __iomem *base;

> +	int *irq;

> +	spinlock_t lock; /* protect gpio register */

> +	struct device *dev;

> +	struct gpio_chip gpio_chip;

> +	struct irq_chip irq_chip;

> +};

> +

> +static void visconti_gpio_irq_mask(struct irq_data *d)

> +{

> +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);

> +	struct visconti_gpio *priv = gpiochip_get_data(gc);

> +

> +	disable_irq_nosync(priv->irq[irqd_to_hwirq(d)]);

> +}

> +

> +static void visconti_gpio_irq_unmask(struct irq_data *d)

> +{

> +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);

> +	struct visconti_gpio *priv = gpiochip_get_data(gc);

> +

> +	enable_irq(priv->irq[irqd_to_hwirq(d)]);

> +}

> +

> +static int visconti_gpio_irq_set_type(struct irq_data *d, unsigned int type)

> +{

> +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);

> +	struct visconti_gpio *priv = gpiochip_get_data(gc);

> +	u32 offset = irqd_to_hwirq(d);

> +	u32 bit = BIT(offset);

> +	u32 intc_type = IRQ_TYPE_EDGE_RISING;

> +	u32 intmode, odata;

> +	int ret = 0;

> +	unsigned long flags;

> +

> +	spin_lock_irqsave(&priv->lock, flags);

> +

> +	odata = readl(priv->base + GPIO_ODATA);

> +	intmode = readl(priv->base + GPIO_INTMODE);

> +

> +	switch (type) {

> +	case IRQ_TYPE_EDGE_RISING:

> +		odata &= ~bit;

> +		intmode &= ~bit;

> +		break;

> +	case IRQ_TYPE_EDGE_FALLING:

> +		odata |= bit;

> +		intmode &= ~bit;

> +		break;

> +	case IRQ_TYPE_EDGE_BOTH:

> +		intmode |= bit;

> +		break;

> +	case IRQ_TYPE_LEVEL_HIGH:

> +		intc_type = IRQ_TYPE_LEVEL_HIGH;

> +		odata &= ~bit;

> +		intmode &= ~bit;

> +		break;

> +	case IRQ_TYPE_LEVEL_LOW:

> +		intc_type = IRQ_TYPE_LEVEL_HIGH;

> +		odata |= bit;

> +		intmode &= ~bit;

> +		break;

> +	default:

> +		ret = -EINVAL;

> +		goto err;

> +	}

> +

> +	writel(odata, priv->base + GPIO_ODATA);

> +	writel(intmode, priv->base + GPIO_INTMODE);

> +	irq_set_irq_type(priv->irq[offset], intc_type);

> +err:

> +	spin_unlock_irqrestore(&priv->lock, flags);

> +

> +	return ret;

> +}

> +

> +static irqreturn_t visconti_gpio_irq_handler(int irq, void *dev_id)

> +{

> +	struct visconti_gpio *priv = dev_id;

> +	u32 offset = irq - priv->irq[0];

> +

> +	generic_handle_irq(irq_find_mapping(priv->gpio_chip.irq.domain, offset));

> +

> +	return IRQ_HANDLED;

> +}

> +

> +static void visconti_init_irq_valid_mask(struct gpio_chip *chip, unsigned long *valid_mask,

> +					 unsigned int ngpios)

> +{

> +	int i;

> +

> +	/* Exclude GPIO pins 16-31 from irq */

> +	for (i = 16; i < ngpios; i++)

> +		clear_bit(i, valid_mask);

> +}

> +

> +static int visconti_gpio_probe(struct platform_device *pdev)

> +{

> +	struct device *dev = &pdev->dev;

> +	struct visconti_gpio *priv;

> +	struct irq_chip *irq_chip;

> +	struct irq_desc *desc;

> +	struct gpio_irq_chip *girq;

> +	const char *name = dev_name(dev);

> +	int i, ret, num_irq;

> +

> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);

> +	if (!priv)

> +		return -ENOMEM;

> +

> +	priv->dev = dev;

> +	spin_lock_init(&priv->lock);

> +

> +	priv->base = devm_platform_ioremap_resource(pdev, 0);

> +	if (IS_ERR(priv->base))

> +		return PTR_ERR(priv->base);

> +

> +	ret = platform_irq_count(pdev);

> +	if (!ret) {

> +		dev_err(dev, "Couldn't determine # GPIO banks\n");

> +		return -ENOENT;

> +	}


platform_irq_count() can return -EPROBE_DEFER. Is that something that
should be handled?

With the above two comments addressed, feel free to add 

Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>


Thanks,
Punit


> +	num_irq = ret;

> +

> +	priv->irq = devm_kcalloc(dev, num_irq, sizeof(priv->irq), GFP_KERNEL);

> +	if (!priv->irq)

> +		return -ENOMEM;

> +

> +	for (i = 0; i < num_irq; i++) {

> +		priv->irq[i] = platform_get_irq(pdev, i);

> +		if (priv->irq[i] < 0) {

> +			dev_err(dev, "invalid IRQ[%d]\n", i);

> +			return priv->irq[i];

> +		}

> +	}

> +

> +	ret = bgpio_init(&priv->gpio_chip, dev, 4,

> +			 priv->base + GPIO_IDATA,

> +			 priv->base + GPIO_OSET,

> +			 priv->base + GPIO_OCLR,

> +			 priv->base + GPIO_DIR,

> +			 NULL,

> +			 0);

> +	if (ret) {

> +		dev_err(dev, "unable to init generic GPIO\n");

> +		return ret;

> +	}

> +

> +	priv->gpio_chip.irq.init_valid_mask = visconti_init_irq_valid_mask;

> +

> +	irq_chip = &priv->irq_chip;

> +	irq_chip->name = "gpio-visconti";

> +	irq_chip->irq_mask = visconti_gpio_irq_mask;

> +	irq_chip->irq_unmask = visconti_gpio_irq_unmask;

> +	irq_chip->irq_set_type = visconti_gpio_irq_set_type;

> +	irq_chip->flags = IRQCHIP_SET_TYPE_MASKED | IRQCHIP_MASK_ON_SUSPEND;

> +

> +	girq = &priv->gpio_chip.irq;

> +	girq->chip = irq_chip;

> +	/* This will let us handle the parent IRQ in the driver */

> +	girq->parent_handler = NULL;

> +	girq->num_parents = 0;

> +	girq->parents = NULL;

> +	girq->default_type = IRQ_TYPE_NONE;

> +	girq->handler = handle_level_irq;

> +

> +	ret = devm_gpiochip_add_data(dev, &priv->gpio_chip, priv);

> +	if (ret) {

> +		dev_err(dev, "failed to add GPIO chip\n");

> +		return ret;

> +	}

> +

> +	for (i = 0; i < num_irq; i++) {

> +		desc = irq_to_desc(priv->irq[i]);

> +		desc->status_use_accessors |= IRQ_NOAUTOEN;

> +		if (devm_request_irq(dev, priv->irq[i],

> +				     visconti_gpio_irq_handler, 0, name, priv)) {

> +			dev_err(dev, "failed to request IRQ[%d]\n", i);

> +			return -ENOENT;

> +		}

> +	}

> +

> +	return ret;

> +}

> +

> +static const struct of_device_id visconti_gpio_of_match[] = {

> +	{ .compatible = "toshiba,gpio-tmpv7708", },

> +	{ /* end of table */ }

> +};

> +MODULE_DEVICE_TABLE(of, visconti_gpio_of_match);

> +

> +static struct platform_driver visconti_gpio_driver = {

> +	.probe		= visconti_gpio_probe,

> +	.driver		= {

> +		.name	= "visconti_gpio",

> +		.of_match_table = of_match_ptr(visconti_gpio_of_match),

> +	}

> +};

> +module_platform_driver(visconti_gpio_driver);

> +

> +MODULE_AUTHOR("Toshiba Electronic Devices & Storage Corporation");

> +MODULE_AUTHOR("Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>");

> +MODULE_DESCRIPTION("Toshiba Visconti GPIO Driver");

> +MODULE_LICENSE("GPL v2");


[...]
Nobuhiro Iwamatsu Dec. 11, 2020, 12:13 a.m. UTC | #2
Hi,

Thanks for your review.

On Thu, Dec 03, 2020 at 07:03:27PM +0900, Punit Agrawal wrote:
> Hi Iwamatsu-san,
> 
> A couple of very minor comments below -
> 
> Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> writes:
> 
> > Add the GPIO driver for Toshiba Visconti ARM SoCs.
> >
> > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > ---
> >  drivers/gpio/Kconfig                      |   9 +
> >  drivers/gpio/Makefile                     |   1 +
> >  drivers/gpio/gpio-visconti.c              | 232 ++++++++++++++++++++++
> >  drivers/pinctrl/visconti/pinctrl-common.c |  23 +++
> >  4 files changed, 265 insertions(+)
> >  create mode 100644 drivers/gpio/gpio-visconti.c
> >
> 
> [...]
> 
> > diff --git a/drivers/gpio/gpio-visconti.c b/drivers/gpio/gpio-visconti.c
> > new file mode 100644
> > index 000000000000..17e6da161f48
> > --- /dev/null
> > +++ b/drivers/gpio/gpio-visconti.c
> > @@ -0,0 +1,232 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Toshiba Visconti GPIO Support
> > + *
> > + * (C) Copyright 2020 Toshiba Electronic Devices & Storage Corporation
> > + * (C) Copyright 2020 Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > + */
> > +
> > +#include <linux/init.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/module.h>
> > +#include <linux/io.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/gpio/driver.h>
> > +#include <linux/of.h>
> > +#include <linux/bitops.h>
> > +
> > +/* register offset */
> > +#define GPIO_DIR	0x00
> > +#define GPIO_IDATA	0x08
> > +#define GPIO_ODATA	0x10
> > +#define GPIO_OSET	0x18
> > +#define GPIO_OCLR	0x20
> > +#define GPIO_INTMODE	0x30
> > +
> > +#define VISCONTI_GPIO_NR	32
> 
> The macro doesn't seem to be used. Can we drop this? On the other hand
> should there be a macro to indicate the maximum number of GPIO lines
> that support interrupt (16)?

Thanks, I will drop this macro.
And about interrutp, it supports with this patch.

> 
> > +
> > +struct visconti_gpio {
> > +	void __iomem *base;
> > +	int *irq;
> > +	spinlock_t lock; /* protect gpio register */
> > +	struct device *dev;
> > +	struct gpio_chip gpio_chip;
> > +	struct irq_chip irq_chip;
> > +};
> > +
> > +static void visconti_gpio_irq_mask(struct irq_data *d)
> > +{
> > +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> > +	struct visconti_gpio *priv = gpiochip_get_data(gc);
> > +
> > +	disable_irq_nosync(priv->irq[irqd_to_hwirq(d)]);
> > +}
> > +
> > +static void visconti_gpio_irq_unmask(struct irq_data *d)
> > +{
> > +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> > +	struct visconti_gpio *priv = gpiochip_get_data(gc);
> > +
> > +	enable_irq(priv->irq[irqd_to_hwirq(d)]);
> > +}
> > +
> > +static int visconti_gpio_irq_set_type(struct irq_data *d, unsigned int type)
> > +{
> > +	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> > +	struct visconti_gpio *priv = gpiochip_get_data(gc);
> > +	u32 offset = irqd_to_hwirq(d);
> > +	u32 bit = BIT(offset);
> > +	u32 intc_type = IRQ_TYPE_EDGE_RISING;
> > +	u32 intmode, odata;
> > +	int ret = 0;
> > +	unsigned long flags;
> > +
> > +	spin_lock_irqsave(&priv->lock, flags);
> > +
> > +	odata = readl(priv->base + GPIO_ODATA);
> > +	intmode = readl(priv->base + GPIO_INTMODE);
> > +
> > +	switch (type) {
> > +	case IRQ_TYPE_EDGE_RISING:
> > +		odata &= ~bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	case IRQ_TYPE_EDGE_FALLING:
> > +		odata |= bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	case IRQ_TYPE_EDGE_BOTH:
> > +		intmode |= bit;
> > +		break;
> > +	case IRQ_TYPE_LEVEL_HIGH:
> > +		intc_type = IRQ_TYPE_LEVEL_HIGH;
> > +		odata &= ~bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	case IRQ_TYPE_LEVEL_LOW:
> > +		intc_type = IRQ_TYPE_LEVEL_HIGH;
> > +		odata |= bit;
> > +		intmode &= ~bit;
> > +		break;
> > +	default:
> > +		ret = -EINVAL;
> > +		goto err;
> > +	}
> > +
> > +	writel(odata, priv->base + GPIO_ODATA);
> > +	writel(intmode, priv->base + GPIO_INTMODE);
> > +	irq_set_irq_type(priv->irq[offset], intc_type);
> > +err:
> > +	spin_unlock_irqrestore(&priv->lock, flags);
> > +
> > +	return ret;
> > +}
> > +
> > +static irqreturn_t visconti_gpio_irq_handler(int irq, void *dev_id)
> > +{
> > +	struct visconti_gpio *priv = dev_id;
> > +	u32 offset = irq - priv->irq[0];
> > +
> > +	generic_handle_irq(irq_find_mapping(priv->gpio_chip.irq.domain, offset));
> > +
> > +	return IRQ_HANDLED;
> > +}
> > +
> > +static void visconti_init_irq_valid_mask(struct gpio_chip *chip, unsigned long *valid_mask,
> > +					 unsigned int ngpios)
> > +{
> > +	int i;
> > +
> > +	/* Exclude GPIO pins 16-31 from irq */
> > +	for (i = 16; i < ngpios; i++)
> > +		clear_bit(i, valid_mask);
> > +}
> > +
> > +static int visconti_gpio_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct visconti_gpio *priv;
> > +	struct irq_chip *irq_chip;
> > +	struct irq_desc *desc;
> > +	struct gpio_irq_chip *girq;
> > +	const char *name = dev_name(dev);
> > +	int i, ret, num_irq;
> > +
> > +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > +	if (!priv)
> > +		return -ENOMEM;
> > +
> > +	priv->dev = dev;
> > +	spin_lock_init(&priv->lock);
> > +
> > +	priv->base = devm_platform_ioremap_resource(pdev, 0);
> > +	if (IS_ERR(priv->base))
> > +		return PTR_ERR(priv->base);
> > +
> > +	ret = platform_irq_count(pdev);
> > +	if (!ret) {
> > +		dev_err(dev, "Couldn't determine # GPIO banks\n");
> > +		return -ENOENT;
> > +	}
> 
> platform_irq_count() can return -EPROBE_DEFER. Is that something that
> should be handled?

I see. In case of an error, I will change it to return ret directly.

> 
> With the above two comments addressed, feel free to add 
> 
> Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
> 

Thank you.

> Thanks,
> Punit
> 

Best regards.,
  Nobuhiro

> 
> > +	num_irq = ret;
> > +
> > +	priv->irq = devm_kcalloc(dev, num_irq, sizeof(priv->irq), GFP_KERNEL);
> > +	if (!priv->irq)
> > +		return -ENOMEM;
> > +
> > +	for (i = 0; i < num_irq; i++) {
> > +		priv->irq[i] = platform_get_irq(pdev, i);
> > +		if (priv->irq[i] < 0) {
> > +			dev_err(dev, "invalid IRQ[%d]\n", i);
> > +			return priv->irq[i];
> > +		}
> > +	}
> > +
> > +	ret = bgpio_init(&priv->gpio_chip, dev, 4,
> > +			 priv->base + GPIO_IDATA,
> > +			 priv->base + GPIO_OSET,
> > +			 priv->base + GPIO_OCLR,
> > +			 priv->base + GPIO_DIR,
> > +			 NULL,
> > +			 0);
> > +	if (ret) {
> > +		dev_err(dev, "unable to init generic GPIO\n");
> > +		return ret;
> > +	}
> > +
> > +	priv->gpio_chip.irq.init_valid_mask = visconti_init_irq_valid_mask;
> > +
> > +	irq_chip = &priv->irq_chip;
> > +	irq_chip->name = "gpio-visconti";
> > +	irq_chip->irq_mask = visconti_gpio_irq_mask;
> > +	irq_chip->irq_unmask = visconti_gpio_irq_unmask;
> > +	irq_chip->irq_set_type = visconti_gpio_irq_set_type;
> > +	irq_chip->flags = IRQCHIP_SET_TYPE_MASKED | IRQCHIP_MASK_ON_SUSPEND;
> > +
> > +	girq = &priv->gpio_chip.irq;
> > +	girq->chip = irq_chip;
> > +	/* This will let us handle the parent IRQ in the driver */
> > +	girq->parent_handler = NULL;
> > +	girq->num_parents = 0;
> > +	girq->parents = NULL;
> > +	girq->default_type = IRQ_TYPE_NONE;
> > +	girq->handler = handle_level_irq;
> > +
> > +	ret = devm_gpiochip_add_data(dev, &priv->gpio_chip, priv);
> > +	if (ret) {
> > +		dev_err(dev, "failed to add GPIO chip\n");
> > +		return ret;
> > +	}
> > +
> > +	for (i = 0; i < num_irq; i++) {
> > +		desc = irq_to_desc(priv->irq[i]);
> > +		desc->status_use_accessors |= IRQ_NOAUTOEN;
> > +		if (devm_request_irq(dev, priv->irq[i],
> > +				     visconti_gpio_irq_handler, 0, name, priv)) {
> > +			dev_err(dev, "failed to request IRQ[%d]\n", i);
> > +			return -ENOENT;
> > +		}
> > +	}
> > +
> > +	return ret;
> > +}
> > +
> > +static const struct of_device_id visconti_gpio_of_match[] = {
> > +	{ .compatible = "toshiba,gpio-tmpv7708", },
> > +	{ /* end of table */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, visconti_gpio_of_match);
> > +
> > +static struct platform_driver visconti_gpio_driver = {
> > +	.probe		= visconti_gpio_probe,
> > +	.driver		= {
> > +		.name	= "visconti_gpio",
> > +		.of_match_table = of_match_ptr(visconti_gpio_of_match),
> > +	}
> > +};
> > +module_platform_driver(visconti_gpio_driver);
> > +
> > +MODULE_AUTHOR("Toshiba Electronic Devices & Storage Corporation");
> > +MODULE_AUTHOR("Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>");
> > +MODULE_DESCRIPTION("Toshiba Visconti GPIO Driver");
> > +MODULE_LICENSE("GPL v2");
> 
> [...]
> 
>
diff mbox series

Patch

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 5d4de5cd6759..85d0f4499d63 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -631,6 +631,15 @@  config GPIO_VF610
 	help
 	  Say yes here to support Vybrid vf610 GPIOs.
 
+config GPIO_VISCONTI
+	tristate "Toshiba Visconti GPIO support"
+	depends on ARCH_VISCONTI || COMPILE_TEST
+	depends on OF_GPIO
+	select GPIOLIB_IRQCHIP
+	select GPIO_GENERIC
+	help
+	  Say yes here to support GPIO on Tohisba Visconti.
+
 config GPIO_VR41XX
 	tristate "NEC VR4100 series General-purpose I/O Uint support"
 	depends on CPU_VR41XX
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 09dada80ac34..02c9d8d83a54 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -162,6 +162,7 @@  obj-$(CONFIG_GPIO_UCB1400)		+= gpio-ucb1400.o
 obj-$(CONFIG_GPIO_UNIPHIER)		+= gpio-uniphier.o
 obj-$(CONFIG_GPIO_VF610)		+= gpio-vf610.o
 obj-$(CONFIG_GPIO_VIPERBOARD)		+= gpio-viperboard.o
+obj-$(CONFIG_GPIO_VISCONTI)		+= gpio-visconti.o
 obj-$(CONFIG_GPIO_VR41XX)		+= gpio-vr41xx.o
 obj-$(CONFIG_GPIO_VX855)		+= gpio-vx855.o
 obj-$(CONFIG_GPIO_WCD934X)		+= gpio-wcd934x.o
diff --git a/drivers/gpio/gpio-visconti.c b/drivers/gpio/gpio-visconti.c
new file mode 100644
index 000000000000..17e6da161f48
--- /dev/null
+++ b/drivers/gpio/gpio-visconti.c
@@ -0,0 +1,232 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Toshiba Visconti GPIO Support
+ *
+ * (C) Copyright 2020 Toshiba Electronic Devices & Storage Corporation
+ * (C) Copyright 2020 Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/gpio/driver.h>
+#include <linux/of.h>
+#include <linux/bitops.h>
+
+/* register offset */
+#define GPIO_DIR	0x00
+#define GPIO_IDATA	0x08
+#define GPIO_ODATA	0x10
+#define GPIO_OSET	0x18
+#define GPIO_OCLR	0x20
+#define GPIO_INTMODE	0x30
+
+#define VISCONTI_GPIO_NR	32
+
+struct visconti_gpio {
+	void __iomem *base;
+	int *irq;
+	spinlock_t lock; /* protect gpio register */
+	struct device *dev;
+	struct gpio_chip gpio_chip;
+	struct irq_chip irq_chip;
+};
+
+static void visconti_gpio_irq_mask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct visconti_gpio *priv = gpiochip_get_data(gc);
+
+	disable_irq_nosync(priv->irq[irqd_to_hwirq(d)]);
+}
+
+static void visconti_gpio_irq_unmask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct visconti_gpio *priv = gpiochip_get_data(gc);
+
+	enable_irq(priv->irq[irqd_to_hwirq(d)]);
+}
+
+static int visconti_gpio_irq_set_type(struct irq_data *d, unsigned int type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct visconti_gpio *priv = gpiochip_get_data(gc);
+	u32 offset = irqd_to_hwirq(d);
+	u32 bit = BIT(offset);
+	u32 intc_type = IRQ_TYPE_EDGE_RISING;
+	u32 intmode, odata;
+	int ret = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->lock, flags);
+
+	odata = readl(priv->base + GPIO_ODATA);
+	intmode = readl(priv->base + GPIO_INTMODE);
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		odata &= ~bit;
+		intmode &= ~bit;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		odata |= bit;
+		intmode &= ~bit;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		intmode |= bit;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		intc_type = IRQ_TYPE_LEVEL_HIGH;
+		odata &= ~bit;
+		intmode &= ~bit;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		intc_type = IRQ_TYPE_LEVEL_HIGH;
+		odata |= bit;
+		intmode &= ~bit;
+		break;
+	default:
+		ret = -EINVAL;
+		goto err;
+	}
+
+	writel(odata, priv->base + GPIO_ODATA);
+	writel(intmode, priv->base + GPIO_INTMODE);
+	irq_set_irq_type(priv->irq[offset], intc_type);
+err:
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	return ret;
+}
+
+static irqreturn_t visconti_gpio_irq_handler(int irq, void *dev_id)
+{
+	struct visconti_gpio *priv = dev_id;
+	u32 offset = irq - priv->irq[0];
+
+	generic_handle_irq(irq_find_mapping(priv->gpio_chip.irq.domain, offset));
+
+	return IRQ_HANDLED;
+}
+
+static void visconti_init_irq_valid_mask(struct gpio_chip *chip, unsigned long *valid_mask,
+					 unsigned int ngpios)
+{
+	int i;
+
+	/* Exclude GPIO pins 16-31 from irq */
+	for (i = 16; i < ngpios; i++)
+		clear_bit(i, valid_mask);
+}
+
+static int visconti_gpio_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct visconti_gpio *priv;
+	struct irq_chip *irq_chip;
+	struct irq_desc *desc;
+	struct gpio_irq_chip *girq;
+	const char *name = dev_name(dev);
+	int i, ret, num_irq;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	spin_lock_init(&priv->lock);
+
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	ret = platform_irq_count(pdev);
+	if (!ret) {
+		dev_err(dev, "Couldn't determine # GPIO banks\n");
+		return -ENOENT;
+	}
+	num_irq = ret;
+
+	priv->irq = devm_kcalloc(dev, num_irq, sizeof(priv->irq), GFP_KERNEL);
+	if (!priv->irq)
+		return -ENOMEM;
+
+	for (i = 0; i < num_irq; i++) {
+		priv->irq[i] = platform_get_irq(pdev, i);
+		if (priv->irq[i] < 0) {
+			dev_err(dev, "invalid IRQ[%d]\n", i);
+			return priv->irq[i];
+		}
+	}
+
+	ret = bgpio_init(&priv->gpio_chip, dev, 4,
+			 priv->base + GPIO_IDATA,
+			 priv->base + GPIO_OSET,
+			 priv->base + GPIO_OCLR,
+			 priv->base + GPIO_DIR,
+			 NULL,
+			 0);
+	if (ret) {
+		dev_err(dev, "unable to init generic GPIO\n");
+		return ret;
+	}
+
+	priv->gpio_chip.irq.init_valid_mask = visconti_init_irq_valid_mask;
+
+	irq_chip = &priv->irq_chip;
+	irq_chip->name = "gpio-visconti";
+	irq_chip->irq_mask = visconti_gpio_irq_mask;
+	irq_chip->irq_unmask = visconti_gpio_irq_unmask;
+	irq_chip->irq_set_type = visconti_gpio_irq_set_type;
+	irq_chip->flags = IRQCHIP_SET_TYPE_MASKED | IRQCHIP_MASK_ON_SUSPEND;
+
+	girq = &priv->gpio_chip.irq;
+	girq->chip = irq_chip;
+	/* This will let us handle the parent IRQ in the driver */
+	girq->parent_handler = NULL;
+	girq->num_parents = 0;
+	girq->parents = NULL;
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_level_irq;
+
+	ret = devm_gpiochip_add_data(dev, &priv->gpio_chip, priv);
+	if (ret) {
+		dev_err(dev, "failed to add GPIO chip\n");
+		return ret;
+	}
+
+	for (i = 0; i < num_irq; i++) {
+		desc = irq_to_desc(priv->irq[i]);
+		desc->status_use_accessors |= IRQ_NOAUTOEN;
+		if (devm_request_irq(dev, priv->irq[i],
+				     visconti_gpio_irq_handler, 0, name, priv)) {
+			dev_err(dev, "failed to request IRQ[%d]\n", i);
+			return -ENOENT;
+		}
+	}
+
+	return ret;
+}
+
+static const struct of_device_id visconti_gpio_of_match[] = {
+	{ .compatible = "toshiba,gpio-tmpv7708", },
+	{ /* end of table */ }
+};
+MODULE_DEVICE_TABLE(of, visconti_gpio_of_match);
+
+static struct platform_driver visconti_gpio_driver = {
+	.probe		= visconti_gpio_probe,
+	.driver		= {
+		.name	= "visconti_gpio",
+		.of_match_table = of_match_ptr(visconti_gpio_of_match),
+	}
+};
+module_platform_driver(visconti_gpio_driver);
+
+MODULE_AUTHOR("Toshiba Electronic Devices & Storage Corporation");
+MODULE_AUTHOR("Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>");
+MODULE_DESCRIPTION("Toshiba Visconti GPIO Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pinctrl/visconti/pinctrl-common.c b/drivers/pinctrl/visconti/pinctrl-common.c
index 0cb10b7b4430..21c7e0d18fea 100644
--- a/drivers/pinctrl/visconti/pinctrl-common.c
+++ b/drivers/pinctrl/visconti/pinctrl-common.c
@@ -245,11 +245,34 @@  static int visconti_set_mux(struct pinctrl_dev *pctldev,
 	return 0;
 }
 
+static int visconti_gpio_request_enable(struct pinctrl_dev *pctldev,
+				      struct pinctrl_gpio_range *range,
+				      unsigned int pin)
+{
+	struct visconti_pinctrl *priv = pinctrl_dev_get_drvdata(pctldev);
+	const struct visconti_mux *gpio_mux = &priv->devdata->gpio_mux[pin];
+	unsigned long flags;
+	unsigned int val;
+
+	dev_dbg(priv->dev, "%s: pin = %d\n", __func__, pin);
+
+	/* update mux */
+	spin_lock_irqsave(&priv->lock, flags);
+	val = readl(priv->base + gpio_mux->offset);
+	val &= ~gpio_mux->mask;
+	val |= gpio_mux->val;
+	writel(val, priv->base + gpio_mux->offset);
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	return 0;
+}
+
 static const struct pinmux_ops visconti_pinmux_ops = {
 	.get_functions_count	= visconti_get_functions_count,
 	.get_function_name	= visconti_get_function_name,
 	.get_function_groups	= visconti_get_function_groups,
 	.set_mux		= visconti_set_mux,
+	.gpio_request_enable	= visconti_gpio_request_enable,
 	.strict			= true,
 };